Question about Chevrolet 1500

Open Question

1981 chevy c10 250 inline 6 vacuum line problem

At the front of my engine there is 4 vacume lines that come together. those line are connected to a 3" wide rubber piece with four holes on the bottom and four 3" hoses coming out of it 2 of those hoses connect to the vacuum delay valve.the 4 hoses permently attached on that piece are cracked and leaking everywear. i cant find that piece any wear and i dnt know what its called. can you help?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: 96 corsica error cod po441 no purge flow

Look, that code means:
P0441 - Evap emission control system Incorrect purge flow

so try to replace the emission control.

Posted on Jun 19, 2008

Ad
  • 2 Answers

SOURCE: vacuum lines from intake dodge dakota sport v-6 magnum

On my 2002 dodge dakota there is a hose that runs off of the front of the intake manifold(facing front end of the engine compartment) This hose was disconnected and there was a cap on the stud at the bottom the intake. The hose was of course a perfect fit. The engine is now running a bit smoother and the all is well with the world.

Posted on Mar 17, 2009

kidspeedy
  • 321 Answers

SOURCE: vacuum line is disconnected on 2002 chevy s10 2.2L

check cruise control unit.

Posted on Jun 12, 2009

  • 1608 Answers

SOURCE: fuel tank vent valve?

If it`s the one on top of the tank then yes it can be replaced without replacing the whole tank.In order to remove it you have to push down and counter clockwise.If you can`t get one at the dealer then go to the salvage yard and take one off a tank there.If it comes off you could get s check engine light.Good luck.

Posted on Dec 05, 2009

  • 128 Answers

SOURCE: I have a 1987 chevy silverado truck 3/4 ton that

it is called a proportioning valve. hope this helps

Posted on Jan 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1981 Laredo. Where can I get a vacuum line routing and connection diagram?


very very old post
ok i figured your old post out.
you posted a 1981 SJ jeep to jeep grand cherokee section.
this is the early Cherokee and is not grand. 1995+
with no engine stated, wow)
ill not try to guess the engine.
here they are...
258 cu in (4.2 L) AMC I6
360 cu in (5.9 L) AMC V8 2-barrel
360 cu in (5.9 L) AMC V8 4-barrel
401 cu in (6.6 L) AMC V8 4-barrel

made in USA or Australia, ill guess USA

the vacuum setups vary by carb used
and if FED usa or Calif USA setups
fed was called 49 state back when...
and there is the high altitude versions.
and std or HD cooling versions (huge list of vacuum setups, if you want look in alldata.com and behold.
omg one more the Canada version.... (ill skip export versions)
calif versions are huge complex....

so ill guess the 360 2 barrel,

e97fc71a-8109-4b75-9002-a238a4147964.jpg

Jul 08, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Vacuum diagram for a 2004 tiburon


There is only 4 vacuum lines on that engine

1- brake booster line

2- purge line to purge solenoid (top center of throttle body)

3- PCV hose. run straight from PCV to side of intake at base of throttle body

4- fuel pressure regulator line (short small diameter hose runs from #6 intake runner to fuel pressure regulator

5- tube that connects front cam cover to rear cam cover to improve vapor venting

http://www.hyundai-forums.com/attachments/gk-tiburon-coupe-s111-2003-2008/38204d1276396353-vacuum-lines-2004-tiberon-pict0001.jpg

Jun 25, 2012 | Hyundai Tiburon Cars & Trucks

2 Answers

Im not sure what wire goes to the distibutor cap to the spark plug on a 1981 6 cylinder Ford Ranger


Here is the firing order for the 4.9 liter in-line six cylinder engine.


74e7a35.gif

Jun 20, 2010 | 1981 Ford F 150

1 Answer

Ned to now wat the firing order for dist cop shood be for a 1987 ford f100 pick-up truck 300sixcylender stick shift model#333


The F100 ended in 1983, so there is some confusion on your 1987 Ford F100. The F150 started in 1983 and was available in 1987, but not the F100. You have this listed under the 1981 Ford F100 category.
The 300 CID = 4.9L In-Line (Straight) 6-Cylinder.
In order to best answer your question I have included both the 1981 F100 4.9L and 1987 F150 4.9L below. The only difference is with the Distributor Cap Configuration and Connections.

For the 1981 F100 300cid=4.9L:
Firing order:
1-5-3-6-2-4
Cylinders:
(back)
...6
...5
...4
...3
...2
...1
(front)
Distributor:
...(back)
.........4..[.]-clip
2
...................1
6
................5
[.]....3

For the 1987 F150 300cid=4.9L:
Firing Order:
1-5-3-6-2-4
Cylinders:
(back)
..6
..5
..4
..3
..2
..1
(front)
Distributor:
.......(back)
.................4
.....2
[.]
.......................1
..6
.........................[.]-clip
....................5
.......3
.........(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

May 07, 2010 | 1981 Ford F 100

2 Answers

I need a vacuum line diagram


Use a industrial vacume tester, check each port coming off of the manifold, run your lines.

Apr 21, 2010 | 1977 Chevrolet Silverado 2500

1 Answer

Firing order need to know what plug is number 1 and what plug on coil pack is number 1


For the 1993 Chevy Lumina:
I do not know if you have the 2.2L In-Line 4 Cylinder, 3.1L V6, or 3.4L DOHC V6 Engine; however I have included all below.

For the 2.2L (4-Cylinder)
Firing Order:
1-3-4-2
Cylinders:
......(back)
1.....2.....3.....4
......(front)
Ignition Coil Connections:
o <---4
...o <---1
.........
......o <----3
.........o <----2

For the 3.1L V6:
Cylinders:
...(back)
5.............6
3.............4
1.............2
....(front)
Ignition Coil Connections:
.|.1..4.|..|.6..3.|..|.2..5.|


For the 3.4L DOHC V6:
Firing Order:
1-2-3-4-5-6
Cylinders:
.......(back)
1........3.........5
2........4.........6
.......(front)
Ignition Coil Connections:
.|.1..4.|..|.3..6.|..|.2..5.|

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


Apr 09, 2010 | 1993 Chevrolet Lumina

2 Answers

1995 dodge 3500 4wd wont engage have shifter on floor light wont come on or 4wd wont engage


Any time your dealing with a 4x4 system the best start is at you front axle. Its primarily a vacuum leak so check to see if the 2 vac lines are hooked up (its good to check the electric connections.). When your 4 wheel drive is engaged and the motors running you should have vacuum at one or both of thee lines depending on if your in 4 hi or low .
If no vacuum at axle check the Vacum switchs(the plug with 4 vac lines) on top of the transfer case it will have 2 feed lines(grey & green) they conect in to the into the vacum harness on back of motor (passanger side). A vacum schematic is normally located on the raditor core support (right under the hood next to hood release)
Hope this helps

Jan 20, 2010 | 1999 Dodge Ram 2500 4WD

1 Answer

I have A MISS AND WAS WONDERING IF IT IS A BENT VALVE


  1. Well it can happen to the best of us check your firing order again it's actualy pretty simple.
1 3 5
2 4 6 This is how the firing order is 1 3 5 being in the back of the engine towards the fire wall and 2 4 6 in the front. Just place the wires on the corresponding numbers.

Mar 18, 2009 | 1998 Chevrolet Malibu

2 Answers

Front drive, 4 Wheel drive won't engage


that vacume line goes back to the transfer case, the end that goes behind the motor hooks to a steel tube so it does not get hot from the exhaust., my guess it should be hooked up so it will feed vacume to the vacume ball so it can lock in the axels. if you start the car and shift into 4 wheel drive and listen under hood you should hear a hissing sound, that is vacume, if you can't hear it there, you may have to craw under the right side to hear it, probably came unhooked underneith the car

Feb 01, 2009 | 1995 GMC Jimmy

3 Answers

4 wheel drive won't work


There is a vacum powered actuator on the front differential housing on the passenger side. It gets it's vacum from two valves mounted on the firewall just behind the battery(to left). The white line feeds manifold vacum to the valves. Check for vacum at white line with engine running. If no vacum there is a break in line from manifold. If vacum check the pink and blue lines by applying vacum to each one. The vacum should hold. If not check lines from valves to vacum actuator. Most likely it will be the actuator. If both lines hold vacum check valves. Remove electrical connectors from both valves. Connect a wire from one of the terminals of the valve to ground. Touch a wire from the battery + to the other terminal of the valve. Listen for a clicking sound. If no sound valve is bad. Replace valves(s). If this doesn't lead you to the trouble it's probably a mechanical problem inside the differential. However most likely there would other noises.

Dec 20, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...