Question about Cars & Trucks

Open Question

Tension bearing sd33t i need tension setting for main and conrod bearing for a sd33t

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 138 Answers

SOURCE: conrod bearings need to be replaced

If the bearings need replacing the crankshaft will need grinding. After the crank has been ground you will have to buy suitable main and conrod bearings EG: 10thou undersize.
After fitting new bearings to the reground crank no adjustment is necessary.

Posted on Jul 01, 2009

  • 27 Answers

SOURCE: i need all torque specs main bearing caps

haynes manual is the best way

Posted on Oct 07, 2009

Autodarwin
  • 54 Answers

SOURCE: I want to know the torque tension settings for a

I would not trust anyone but the manual on this one got to your local parts store and get a Haynes or Chiltons

Posted on May 27, 2010

  • 266 Answers

SOURCE: need torque settings for 6vd1 main and conrod

43 FT LBS MAINS 49 FT LBS RODS

Posted on Oct 18, 2010

Testimonial: "great thank you and so fast on reply thanks "

alicantecoli
  • 22095 Answers

SOURCE: torque settings conrod bearing 2e engine

tighten with a rachet and a decent socket with the shape of the nut in the end ,tighten to about a grunt and a slight arm muscle strain which is about 50lbs ,in two staged in the book it says 22nm +90? which to me is a load of hog wash ,make sure the shell with the hole in it for the oil spray is in the top con rod end and bit of grease in their as well before you fit the bottom one then a pull down first time with a rachet to firm pull then the second pull ,then turn engine over to make sure its not locked up then do the next one ,the lips in the shells that hold the shell inside the caps normally go together on one side and the con rod oil spray hole should spray towards the thrust side of the piston .

Posted on Feb 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a mitsubishi l300 with a 4G64 engine I have just replaced main bearings it ran ok but now it's blowing smoke. Compression is ok but all the plugs are dry black as if it's getting too much fuel


F]ENGINE Workshop Manual 4G6 (EW) - mmc@mitsubishi-motors.kiev.ua

mitsubishi-motors.kiev.ua/Manuals/Engine/pwee9616/11A.pdf

you have to run it in and wait and see
you may burn up a set of plugs

renew main bearings only raise the conrods and pistons
so piston and rings will run in a different position up the cylinder wall

only doing mains and not conrods and re-ring is a strange thing to do

Apr 16, 2017 | Mitsubishi Cars & Trucks

1 Answer

Main bearing torque settings for a 2c toyota


Main Bearings: 103nm
Conrod bearings: 64nm
Cyl Head: 44nm +90? +90? - USE NEW BOLTS

Aug 18, 2015 | Toyota Cars & Trucks

1 Answer

Hi do i need to replace the main bearing and the conrod bearing bolts on the opel corsa 6W engine 2006 model


it is good mechanical practice to replace all bolts that are operating under tension. That includes con rod bolts , big end bolts fly wheel bolts , head studs and crank shaft bolt. Some manuals recommend the replacement of cam shaft sprocket bolts as well. This practice is recommended where the engine is driven at high rpms. It is recommended practice because the tension effect actually twists the bolt and this combined with the tensional stress makes the bolts prone to failure. As it adds considerably to the cost many mechanics do not follow the practice but will charge for the new bolts as well.

Dec 01, 2014 | 2008 Opel Corsa 1.4

1 Answer

Conrod bearings need to be replaced in the engine that is 3y engine model for hilux and i want to know whether any adjustments needs to be done after installing the bearings


If the bearings need replacing the crankshaft will need grinding. After the crank has been ground you will have to buy suitable main and conrod bearings EG: 10thou undersize.
After fitting new bearings to the reground crank no adjustment is necessary.

Jul 01, 2009 | 1987 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...