Question about 2002 Volkswagen Jetta TDI

1 Answer

VW Jetta torque setting and hub nut size????

Changing right hand rear wheel bearing on my 2002 vw jetta tdi tomorrow and i can't find anywhere torque setting for tightening bearing(hub nut?) and also would like to know what size a socket i kneed so i have all the tools i need before i start.
any help or advice i could get would be greatly appreciated!!
thank you!

Posted by on

  • 3 more comments 
  • Anonymous Mar 22, 2014

    do i start bearing and drive hub with piece wood and hammer

  • Anonymous Mar 23, 2014

    What size socket for hub bearing nut

  • Anonymous Mar 23, 2014

    2004 ponitac Montana
    What size socket for hub bearing nut

  • Anonymous Mar 23, 2014

    What size socket for hub bearing

  • Anonymous Mar 23, 2014

    What size socket for hub bearing

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Posted on Jun 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace a rear wheel bearing hub?


Remove brake components, remove centre cover to expose securing nut, remove nut and using a 3 jaw puller remove the bearing and hub. The inner race will remain on the spindle and will need to be cut off being carefully not to cut the spindle. I use a cutting torch to achieve this. ER the spindle cool befor installing the new bearing/hub assy. Don't forget to torque the nut to spec. I can't remember offhand what it is but if you over tighten it the braring life will be reduced. Also use a new nut as they are one time use and may loosen over time if reused.
Good luck!

Feb 22, 2015 | 2002 Volkswagen Jetta TDI

1 Answer

Removal of front fender on 2002 VW-Jetta 2.0L


Hi. The only one I know of that will help in this case is ErWin, google it. have your VIN ready.

May 04, 2014 | 2002 Volkswagen Jetta TDI

1 Answer

How to remove right-front fender on a 2002 VW-Jetta 2.0L


This should get you going.

http://forums.vwvortex.com/showthread.php?786590-just-posting-for-the-diy-post

May 04, 2014 | 2002 Volkswagen Jetta TDI

1 Answer

2002 vw jetta service manual


how to replace diff bearing 2002 vw jetta tdi deisel

May 01, 2012 | 2002 Volkswagen Jetta TDI

1 Answer

Dont have a problem yet. want to avoid problems. need to know what to do fro service. have 124000 miles on 2.0 jetta and never had anything but oil changed and oil filter.


Very nice to know that somebody care of his car.I understood that this is 1.9 TDI JETTA in124000 miles.To avoid problems in the future you have to change gearbox oil by recommended from a manufacturer.Second-Check all wheel bearings/rear ones/ for noise.Also make suspension test. any way you have to visit vw workshop for full diagnostic of the JETTA

Jun 09, 2011 | 2000 Volkswagen Jetta TDI

2 Answers

I have a 2002 VW Jetta and the temperature gauge keeps going up and down... Is this something to worry about ?


Replace the Engine Coolant Temperature (ECT) sensor. ECT sensor is placed in the right back side of the cylinder head on 2002 VW Jetta 1.9 TDI. See picture below:

tdisline_212.jpg

Please do rate my response. Thanks!

Feb 04, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

What is the torque for the rear wheel bearing nuts on 1991 vw jetta diesel


Temporarly torque the axle nut to 87 in.lb., while turning the brake drum by hand. Then loosen the nut slightly. Tighten the axle nut again, slowly and in small increments while turning the wheel, until the thrust washer can just barely be moved back and forth with a light push from the tip of a screwdriver.

Oct 30, 2010 | 1991 Volkswagen Jetta

1 Answer

How to replace rear axle bearings 2004 vw jetta


take off rear hub u have a inner and outter bearing ..change bearing dont forget to pack new bearing well with a GAA Bearing Grease...and install wheel and tighten middle nut till wheel is tight...then back it off enough that wheel turn but not too freely about half a turn back....GL

Aug 30, 2009 | 2004 Volkswagen Jetta

1 Answer

I am changing front wheel bearings on 2001 vw jetta. I have the nut off the axle but have not been able to get the hub off in order to get to the bearing. Will I need a gear puller or something similar to...


2 options:  take it to a shop the bearing comes compresed with the hub. you need a machine to do that or buy the hub with the bearing...I say shop its less expensive. GOOD LUCK!

Apr 25, 2009 | 2001 Volkswagen Jetta TDI

Not finding what you are looking for?
2002 Volkswagen Jetta TDI Logo

2,598 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...