Question about Cars & Trucks

Open Question

Gem novopiano dp 30 manual - Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Por favor, necesito diagrama de caja de fusibles para Mazda B2300 del 2001


Mazda B-Series (2001) - fuse box diagram Year of production: 2001

Interior fuse panel

Mazda B-Series - fuse box -
interior fuse panel Number Ampere rating [A] Description 1 5 Power Mirror 2 10 Blower Motor Relay, Air Bag Diagnostic Monitor, Passive Deactivation (PAD) Module 3 7,5 Trailer Tow Connector (LH Stop/Turn) 5 10 4×4 Control Module 7 7,5 Trailer Tow Connector (LH Stop/Turn) 9 7,5 Stoplamp Switch 10 7,5 Cruise Control Servo/Amplifier Assy., GEM/CTM, Shift Lock Actuator, Blend Door Actuator, A/C Heater Control Assy., Turn Signals 11 7,5 Instrument Cluster, Main Light Switch, RABS Resistor 13 20 Brake Pedal Position Switch 14 20 RABS Module 10 4WABS Mod., 4WABS Main Relay 16 30 W/W Motor, Wiper Hi-Lo Relay, Wiper Run/Park Relay, Washer Pump Relay 17 25 Cigar Lighter, Data Link Connector (DLC) 19 25 PCM Power Diode, Ignition, PATS 20 7,5 GEM/CTM, Radio 21 20 Flasher 22 20 Auxiliary Power Point 24 7,5 Clutch Pedal Position (CPP) Switch, Starter Interrupt Relay 26 10 Battery Saver Relay, 4×4 Electronic Shift Relay, Interior Lamp Relay, 4×4 Elec. Shift Control Module, Dome/Map Lamp, Instrument Illumination Dimming Module, Restraint Control Module, GEM/CTM, Instrument Cluster 28 7,5 GEM/CTM System, Radio 29 15 Radio 33 15 Headlights, DRL Module, Instrument Cluster 35 15 ISA Horn Relay if not Equipped with Truck Security Module

Engine compartment fuse block

Mazda B-Series - fuse box -
engine compartment Number Ampere rating [A] Description 1 50 I/P Fuse Panel 6 50 ABS Pump Motor 7 30 Powertrain Control Module 8 20 Power Door Locks and Remote Entry 11 50 Starter Relay Ignition Switch 12 10 PCM Memory 13 20 4×4 Motor 16 40 Blower Motor 21 10 PCM Memory 23 20 Fuel Pump Motor 24 30 Headlights 25 10 A/C Clurtch 28 30 4WABS Module 30 15 Trailer Tow 31 20 Fog Lamps, Day Time Running Lamps (DRL) 33 15 Park Lamp 38 10 Left Headlamp Low Beam 41 - Heated Oxygen Sensors 42 10 Right Headlamp Low Beam 45A - Wiper High/Low 45B - Wiper Park/Run 46A 46B - Front Washer Pump 47A 48A - Fog Lamp 48B - Fog Lamp Relay 49 - Full Starter 50A 50B - Fuel Pump 53 - Powertrain Control Module (PCM) Diode 54 - Powertrain Control Module (PCM) Diode 55 - Blower 56A - A/C Clutch Solenoid 56B - Trailer Tow

Jul 04, 2017 | Mazda Cars & Trucks

1 Answer

Where is the four wheel module located on a 2001 f350 7.3 l lariat 4x4 nothing on the four wheel drive works and I checked all the fuses and are all fine


Have it check for DTC'S - diagnostic trouble codes ?
GEM Diagnostic Trouble Code (DTC) Index
GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action C1728 Transfer Case Unable to Transition Between 2H and 4H GEM CARRY OUT the electronic shift function test. REFER to Function Test - Electronic Shift in this section. C1729 Transfer Case Unable to Transition Between 4H and 4L GEM CARRY OUT the electronic shift function test. REFER to Function Test - Electronic Shift in this section. P0500 Vehicle Speed Sensor (VSS) Malfunction GEM GO to Pinpoint Test F . P1804 Transmission 4-Wheel Drive High Indicator Circuit Failure GEM GO to Pinpoint Test H . P1808 Transmission 4-Wheel Drive Low Indicator Circuit Failure GEM GO to Pinpoint Test I . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure GEM GO to Pinpoint Test E . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground GEM GO to Pinpoint Test E . P1819 Transmission Park/Neutral Position Switch Short Circuit to Ground GEM GO to Pinpoint Test F . P1820 Transmission Transfer Case Clockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test E . P1822 Transmission Transfer Case Clockwise Shift Relay Coil Short to Battery GEM GO to Pinpoint Test E . P1828 Transfer Case Counterclockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test E . P1830 Transmission Transfer Case Counterclockwise Shift Relay Coil Short Circuit to Battery GEM GO to Pinpoint Test E . P1832 Transmission Transfer Case Differential Lockup Solenoid Circuit Failure GEM GO to Pinpoint Test G . P1834 Transmission Transfer Case Differential Lockup Solenoid Short Circuit to Battery GEM GO to Pinpoint Test G . P1865 Transmission Transfer Case Contact Plate Power Short to Ground GEM GO to Pinpoint Test E . P1866 Transmission Transfer Case System Concern - Servicing Required GEM CARRY OUT the electronic shift function test. REFER to Function Test - Electronic Shift in this section. P1867 Transmission Transfer Case Contact Plate General Circuit Failure GEM GO to Pinpoint Test E . P1876 Transmission Transfer Case 2-Wheel Drive Solenoid Circuit Failure GEM GO to Pinpoint Test G . P1877 Transmission Transfer Case 2-Wheel Drive Solenoid Circuit Short to Battery GEM GO to Pinpoint Test G . - For All Other DTCs GEM GO to Section 419-10 .
Your best bet , take it to a qualified repair shop that has the diagnostic tool to trouble shoot .
Principles of Operation
Transfer Case - Electronic Shift
The four-wheel drive, electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4X4 HIGH, and 4X4 LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators, one for 4X4 HIGH which is 4X4, and one for 4X4 LOW which is LOW RANGE (in 4X4 LOW both the lamps are on). Shifts into 4X4 HIGH can be made at any speed. When shifting into 4X4 HIGH with the vehicle stationary, tooth blockage may occur, preventing shift completion. When the vehicle is driven above 8 km/h (5mph) the shift will complete. When shifting in or out of 4X4 LOW, the generic electronic module (GEM) requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission). (The digital transmission range [TR] sensor informs the GEM when the automatic transmission is in the NEUTRAL range position.)
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and the range fork within the transfer case between the 4X4 HIGH, 4X4 LOW, and 2WD range positions.
The GEM uses two relays to control the gearmotor encoder assembly shift between 4X4 HIGH, 4X4 LOW, and 2WD modes. The GEM controls the pulse vacuum hublock (PVH) solenoid which supplies engagement and disengagement vacuum to control the hublocks.
The GEM accomplishes shifts by interpreting inputs from:
  • mode select switch (MSS)
  • vehicle speed signal (transmitted from the ABS system)
  • gearmotor encoder plate position
  • brake pedal switch
  • digital transmission range (TR) sensor (automatic transmission)
  • clutch pedal position (CPP) switch (manual transmission)
  • ignition switch
Based on these inputs, the GEM controls the shifts into 2WD, 4X4 HIGH, or 4X4 LOW with the following outputs:
  • low to high relay (clockwise)
  • high to low relay (counterclockwise)
  • pulse vacuum hublock (PVH) solenoid
  • gearmotor encoder assembly
The electronic shift-on-the-fly (ESOF) system has a feature which allows the driver to override the vacuum operated hublocks. When the front hublocks are manually turned to the LOCK position, the hublocks are locked at all times, overriding the vacuum operated system. If the front hublocks are manually turned to the AUTO position, the hublocks can only be locked by turning the MSS to 4X4 HIGH or 4X4 LOW position.

Jun 12, 2017 | Cars & Trucks

1 Answer

Limited. What is causing battery drain?


To find out what is draining the battery do a parasitic draw test . How To Perform Parasitic Draw Test EricTheCarGuy Test to be sure , before replacing GEM module .I would also have the GEM checked for DTC'S - diagnostic trouble codes . I would also check the battery saver relay .
SECTION 417-02: Interior Lighting 2000 Explorer/Mountaineer Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/17/1999 Interior Lighting The interior lighting system consists of the following:
  • dome/map lamp
  • rear dome/cargo lamp
  • overhead console/map lamp
  • RH/LH vanity mirror
  • ash receptacle lamp
  • puddle lamps
  • interior lamp switches
  • interior lamp relay
  • dimmer module
  • battery saver relay
  • generic electronic module (GEM)
Generic Electronic Module (GEM)/Central Timer Module (CTM) Controlled Functions
The generic electronic module (GEM) is equipped on four-wheel drive vehicles with power windows. The central timer module (CTM) is equipped only on two-wheel drive vehicles without power windows.
NOTE: GEM/CTM diagnostics are compatible with the scan tool.
The GEM/CTM incorporates the functions of several different modules into one, and offers diagnostics to easily locate and repair concerns affecting the subsystems that it controls.
The GEM/CTM constantly monitors the systems it controls and reports a concern in the form of a diagnostic trouble code (DTC). A DTC can be retrieved with the scan tool through the communication link.
The scan tool is a menu-driven tester that allows the user to run specific tests. The scan tool can isolate faults in the GEM/CTM subsystems through a symptom-driven diagnostic procedure. Connecting the scan tool to the GEM/CTM communication link will not alert the GEM/CTM. If the GEM/CTM is "asleep" when the diagnostic connector is plugged in, the GEM/CTM must be "awakened". If the communication link cannot be established, turn the ignition to RUN.
NOTE: The GEM/CTM has a sleep function to minimize battery consumption. During the sleep mode, the GEM/CTM turns off all outputs and monitors only the following:
  • door ajar (driver door, passenger door, liftgate, LH rear and RH rear doors).
  • key-in-ignition.
  • key in RUN or ACC.
  • two-step unlock switch (unarm switch).
  • digital TR sensor.
  • illuminated entry request (remote anti-theft personality [RAP] module).
If a change of status occurs at one of these inputs while the GEM/CTM is "asleep", the GEM/CTM will "wake up." When the GEM/CTM awakens, it carries out an internal self-test, and begins normal operation. At this point, the GEM/CTM will have all of its functions operational.
The GEM/CTM will go into the sleep mode immediately after both of the following conditions have been met:
  • key in OFF or key not in ignition.
  • after 45 minutes with no change in any wake-up input.
The GEM/CTM control system has two modes of operation; the normal operating mode and the tester-dependent diagnostics mode.
Normal operation of the GEM/CTM can detect errors. An integral part of normal GEM/CTM operation is continuous diagnostic capability. Continuous diagnostics detects errors and changes the GEM/CTM control strategy. There is no warning lamp for the GEM/CTM; therefore, a DTC concern will direct you to the GEM/CTM. Examples of faults that may be detected during normal operation include:
NOTE: The GEM/CTM can only detect open circuit/short to GRD faults when the GEM/CTM is not energizing a load, and short to battery faults when the GEM/CTM is attempting to energize a load.
  • GEM/CTM continuous self-test (RAM, ROM, EEPROM, A/D checking).
  • output driver monitoring (open circuit/short to ground [GRD], short to power).
  • illogical combinations of input signals.

Dec 01, 2015 | 2002 Ford Explorer

2 Answers

My battery drains over night. i can hear a relay under the dash clicking. i remove no. 27 fuse and it stops. what is causing this?


Check your owners manual for the number 27 fuse to see what it is. Checking online I see it as a 15 Amp, Under hoop lamp, Map lights, Glove box lamp, Dome lamp, Visor lamps, Accessory delay, Dimmer switch illum. and 4x4 system. check each one to see if the bulb is blown but left on, at least if it's a light. It that doesn't do it, research how to check accessory delay and 4x4 system.

Mar 20, 2015 | 1996 Ford Explorer

1 Answer

What does the abreiviation rcu and gem stand for?


GEM stands for Generic Electronic Module. RCU stands for Rear Control Unit. Your in dash radio is just a faceplate. The audio unit is in the trunk.

Apr 30, 2012 | 1999 Mercury Sable

1 Answer

I don't have a cover for my fuse box and need to


Thanks for the inquiry.
zeppelinx12_4.jpg






Fuse Numbers and Locations:
EXPLORER FUSE PANEL Fuse Position Rating Circuit Protected 1 10 Amp Power Mirrors/Antenna 2 10 Amp Air Bag/Blower Relay 3 15 Amp Parking Lamps 4 15 Amp Left Headlamp 5 10 Amp On Board Diagnostic II System 6 15 Amp HO2S Sensors 7 10 Amp Illumination Switches 8 15 Amp Right Headlamp/Fog Lamp System 9 10 Amp EATC Mem./Seat Mem./Mess. Ctr./Cell. Phone 10 10 Amp EATC Sys./Rear Blower/Spd. Control/GEM Sys./Brake Interlock/OH Console Adapt. Susp. 11 10 Amp Warning Lamps 12 10 Amp Front and Rear Washers 13 15 Amp PCM Sys./Stoplamps/4WD/
ABS/Spd. Control/Trailer Tow 14 10 Amp Anti-Lock System 15 15 Amp Air Bag System/Alternator 16 30 Amp Front Wiper 17 30 Amp Cigar Lighter 18 15 Amp A/C System 19 25 Amp Ignition Coil/PCM System 20 10 Amp Radio/Power Ant./GEM Sys./Anti-Theft/Cell. Phone 21 15 Amp Hazard Lamps 22 15 Amp Turn Signals 23 15 Amp Rear Wiper System 24 15 Amp Starter Relay/Anti-Theft 25 10 Amp Speedometer/GEM System 26 15 Amp A4LDE Trans/DRL Sys./Backup Lamps/4WD/Rear Defroster 27 15 Amp Under Hood LP/Map Lights/Glove Box Lamp/Dome Lamp/Visor Lamps/Accessory Delay/DR Switch Illum./4x4 System 28 10 Amp Memory Seat/GEM System 29 15 Amp Audio System 30 - Not Used 31 10 Amp Aux. Blower System 32 10 Amp Heated Mirrors/Heated Backlite 33 20 Amp High Beam Lamps 34 10 Amp Audio System/Power Antenna 35 - Not Used 36 - Not Used
Hope this helps helps. Please keep us updated and remember to rate this answer.
Kind regards,
TF

Jun 05, 2011 | 1995 Chevrolet S-10 CA Edition

1 Answer

Why doesn't my auto window button work on my ford 01 f150. The window rolls down fine but the auto function doesn't work. It started doing that after I changed a bad battery and put in a new one.


. May need to reprogram module due to disconnect.
CAUTION: Prior to removal of the GEM, it is necessary to upload module configuration information to a diagnostic tool. This information needs to be downloaded into the new module once installed. For additional information, refer to Section 418-01.


----------------
The following is list of GEM/CTM-controlled functions:
  • wipers/washers (front/rear)
  • warning chimes
  • battery saver
  • illuminated entry and courtesy lamps
  • accessory delay
  • driver power window (GEM only)
The GEM constantly monitors its subsystems for concerns. If a concern is found in one of the subsystems, the GEM will record the concern in the form of a diagnostic trouble code (DTC). The ignition switch position is very important to the GEM function. Often times, erratic or unexpected GEM function can be traced to concerns with ignition switch inputs.

Principles of Operation:
The generic electronic module (GEM) controls the opening of the driver window by activating the one-touch down window relay.
The GEM controls manual down and auto down window movement with the down window relay. The relay is activated by applying ground directly to one side of the down window relay coil, and deactivated by removing the ground signal. The delayed accessory relay provides power for the operation of the power windows and the roof opening panel (if equipped). The delayed accessory feature is active when the ignition switch is in the RUN or the ACC position, or when the ignition switch is changed from RUN or ACC to the OFF/LOCK position and the driver and passenger doors are closed.
Down window motion operates in two modes, manual mode and auto mode. When the GEM detects the first down position, first detent on the switch, it enters manual mode. In manual mode, the window will move downward only while the switch is depressed. Similarly, when the GEM detects the second down position, second detent on the switch, it enters auto mode. In auto mode, the window will open completely with just a momentary press of the switch.
the GEM will activate the one-touch down window relay until one of the following conditions is met:
  • The driver window control switch is pushed to the UP position.
  • The driver window control switch is released (OFF position) and then moved to the down position (first detent) or the one-touch down position (second detent).
  • Seven seconds have elapsed since the one-touch down feature was initiated.
  • A window regulator motor stall condition is detected on the one-touch down sense line inputs.
The GEM will deactivate the delayed accessory feature when:
  • the driver/passenger door is ajar and the ignition switch is in the OFF/LOCK or KEY-OUT position.
  • 10 minutes have elapsed since the ignition switch was changed from ACC or RUN to the OFF/LOCK position.
Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical or electrical damage.

    Visual Inspection Chart
    Mechanical Electrical

    • Window regulator motor
    • Window glass
    • Central junction box (CJB) Fuse:
      • 6 (5A)
      • 8 (5A)
      • 15 (5A)
      • 17 (10A)
      • 18 (5A)
      • 20 (5A)
    • Battery junction box (BJB) Fuse:
      • 103 (50A)
      • 110 (30A)
      • 116 (40A)
      • 601 (30A)
    • Relay(s)
    • CJB
    • BJB
    • Window control switch
    • Window regulator motor
    • GEM
    • Circuitry
    • Damaged wiring harness
    • Loose or corroded connector(s)

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the scan tool does not power up:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch is in RUN position.
    • If the scan tool still does not power up, refer to the scan tool manual.
  1. Carry out the DATA LINK DIAGNOSTICS test. If the scan tool responds with:
    • CKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418-00.
    • SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics for the GEM.
  1. If the DTCs retrieved are related to the concern, go to the GEM Diagnostic Trouble Code (DTC) Index to continue diagnostics.
  1. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.
------------------------------------------------
  • The one-touch down feature is inoperative
  • Circuitry.
  • Battery saver relay.
  • One-touch down relay.
  • Driver window control switch.
  • Driver window regulator motor.
  • Central junction box (CJB).
  • Generic electronic module (GEM).

Mar 30, 2011 | 2001 Ford F150 Styleside SuperCrew

1 Answer

I have a 89saab. I have no power to the fuel pump?


Check fuse 22 (10 A - 1989 to 93) it's the fuel system, and fuse 30 (20 A) it's for the fuel pump; there is a relay located behind right side trim panel in front of passenger foot well.

To test the relay, remove it and jumper between sockets 30 and 87b (middle and bottom); if the pump runs, the pump is OK and the relay suspect. If the pump doesn't run, then a circuit is suspect, eg power from relay to pump, or power from battery to relay, or a ground connection. To check these you'll need a wiring diagram - get the "Bentley Bible" - aka the Saab 900 Official Service Manual, costs about $40 from Amazon!

16 valve manual: http://www.amazon.com/Saab-900-Valve-Service-Manual/dp/0837603137

8 valve manual :http://www.amazon.com/Eight-Official-Service-Manual-1981-1988/dp/0837603102
get the appropriate manual for your car and enjoy the Saab!


Most likely it's the relay.


Possible other causes are:
blocked fuel filter - under right rear, in front of gas tank (fuel spills are dangerous - don't smoke, etc!);

broken wire connection to pump - check continuity between fuse 30 and pump connection;

dead pump - you could provide power to the pump to check if it runs;

Apr 21, 2009 | 1988 Saab 900

1 Answer

Radio fuse/cd changer


Number Fuse Amperage
Rating
Circuits Protected
7 7.5 amp Illumination switches
8 10 amp Right headlamp, fog
lamp system
9 10 amp Autolamps
10 7.5 amp Rear blower, speed
control, GEM system,
brake interlock,
overhead console
11 7.5 amp Warning lamps
12 10 amp Liftgate wiper/washer,
front washer
13 15 amp Brake on/off switch
14 10 amp Anti-lock system
15 7.5 amp Air bag system,
instrument cluster
16 30 amp Wiper run relay
17 15 amp Cigar lighter
18 15 amp A/C system
19 25 amp Ignition coil, PCM
system
20 7.5 amp Radio, power antenna,
GEM system,
anti-theft
21 15 amp Turn/hazard flasher
22 10 amp Turn signals
23 10 amp Rear wiper system
24 10 amp Anti-theft relay
25 7.5 amp Instrument cluster,
GEM system

Nov 11, 2008 | 1997 Mercury Mountaineer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...