Question about 2002 Ford Excursion

1 Answer

Comfort access failure.

I have a 2002 Excursion V10 Limited. After some body repair work at a shop, the keyless entry FOB and the locks switch on the D. door wont work. The door ajar light stays on and the radio won't turn off when the engine is off and I open the door. Keyless entry panel also doesn't work. Any idea what they may have done wrong?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,209 Answers

Sounds like they might have missed plugging the door harness in to the body, or maybe left a ground unhooked.

Posted on Apr 24, 2013

Testimonial: "Dan; Do you think that would have been from the rear barn doors or hatch area?"

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2000 windstar

THAT SOUNDS LIKE SOMETHING WITH THE LOCKS THAT ARE SUPPOSED TO WORK WITH THE SHIFTER WHEN PUT IN GEAR. OURS DID THE SAME THING, BUT OUR WARRANTY PAID TO FIX IT, ALTHOUGH IT STILL ISN'T WORKING100%. IT COULD ALSO BE AS SIMPLE AS THE BATTERY IN YOUR KEYLESS ENTRY BEING LOW. ALTHOUGH THAT SHOULDN'T STOP YOU FROM MANUALLY OPENING IT. THAT'S WHAT MAKES ME THINK IT IS THE LOCK MECAHNISM ITSELF. I'M SURE YOU KNOW THAT IT HAS ON/OFF BUTTON FOR THE SLIDER AND IF IT IS OFF IT WON'T WORK, ALSO VAN HAS TO HAVE TO BE IN PARK OR IT WON'T WORK EITHER. TO USE MINE MANUALLY I HAD TO DRAG, YANK AND PULL(HAHA) TO GET IT OPEN. ANY SIGNS OF RUST ON YOURS YET? WE STARTED NOTICING BAD RUST LAST YEAR WHEN THE CAR HAD @50,000 MILES ON IT. ITS DISAPPOINTING TO SEE ALL THESE LITTLE ELECTRICAL PROBLEMS WITH THIS VAN. GOOD LUCK!

Posted on Jul 25, 2008

harley9701ha
  • 424 Answers

SOURCE: 2001 Ford Excursion door locks will not unlock or lock.

Unfortunately the actuators are bad. You could try removing the door panels and disconnect one actuator at a time and possibly only have a couple bad but it is common to have more than on go bad. I hope this helps. Good luck.

Posted on Jul 20, 2009

  • 506 Answers

SOURCE: The door locks on my F250 work intermittently when

I had this problem on my exploder. From what I remember I located the keyless entry receiver underneath the drivers side dashboard there should be a box with the name SIEMENS on it. This is your keyless entry receiver. Unplug the unit for about 1 hour ( do not know why for an hour ) and plug back in after 1 hour. Should work fine after that.

Posted on Jan 28, 2010

  • 11 Answers

SOURCE: ford 2000 excursion keyless entry not working

look online or go to the dealer and find a reprogramming procedure.

Posted on Mar 12, 2010

  • 2976 Answers

SOURCE: Keyless entry isn't working and alarm was tripped

Check your door latches. Since the light stays on, one of them isn't reading properly. Once you get that fixed, the remote should work. The light problem could be related. The computer thinks the door isn't shut so that part of the system thinks you aren't moving.

Posted on Mar 20, 2010

Testimonial: "Very helpful, ended up disconecting the battery to reset the system and that worked."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 crown vic keyfob only works with ignition in run position .keyless entry and door locks work fine.even tried new keyfob.no change


The keyless entry system consists of the following components:
  • driver door module (DDM)
  • keyless entry transmitter
  • keyless entry keypad
The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
  • Battery junction box (BJB) fuses:
    • circuit breaker 7 (20A)
  • Central junction box (CJB)
    • 4 (10A)
    • 6 (15A)
    • 8 (25A)
    • 13 (5A)
  • Keyless entry keypad switch
  • Power door lock actuator
  • Luggage compartment release switch
  • Luggage compartment release solenoid
  • Connectors or connections
  • Wiring harness
  • If fuse's good have checked for DTC'S - diagnostic trouble codes .
  • B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .
  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter not programmed.
  • Remote transmitter.
  • DDM.
  • Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.
  1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.
  1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
  1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

Feb 19, 2017 | Cars & Trucks

1 Answer

Rocker switches,nor remote will lock or unlock doors fuse good


So , the power door locks won't lock or unlock with switches inside the vehicle or with the keyless entry remote fob.??? Is this correct ????
Do you know what a BCM - body control module is ? Do you know what diagnostic trouble codes are ? If not your best bet would be to take your vehicle to a GM dealer or someother qualified repair shop.
DTC B3142 or B3143
The body control module (BCM) provides an output to the driver switch assembly through the door unlock control circuit for controlling automatic door unlock, anti-lockout, and keyless entry unlock functions.
DTC B3152 or B3153
It could be the driver door master switch , could have broken wires inside the rubber boot from the body to the door . Do the power windows work ?
The keyless entry system has the following main components:
• The transmitters
• The body control module (BCM)
When you press a button on a transmitter, the transmitter sends a signal to the BCM. The BCM interprets the signal and activates the requested function.

How did you do this ,,checked and made sure locks and remote programmed,they were,but still do not work ?????

Need a scan tool to program
Important: All key fobs must be programmed each time any one fob is programmed. The scan tool must stay connected until all of the transmitters are programmed.
Install a scan tool and navigate to the BCM Module Setup menu.
Select Program Key Fobs.
Follow the scan tool on-screen directions.
When the programming operations have completed, operate the transmitter functions to verify correct system operation.

Aug 09, 2017 | 2005 Chevrolet Colorado

1 Answer

How does key fob work


Depending on the specification of your vehicle, the FOB generally serves one (or both) of the following functions:

1) Communicate with the vehicle's Keyless Entry system (operates central locking).
2) When inserted into the ignition, the transponder within the key will communicate with the vehicle's Body computer (BEM) to validate entry, before disengaging the immobilizer - allowing the vehicle to start.

When the key fob fails, you may lose functionality of the above systems.

Keyless entry failure - usually due to flat battery in the fob. Reprogramming of keyless entry can be done without dealership assistance.

Transponder/Immobilizer failure - this requires the key fob to be re-programmed by your local dealership.


Hope this helps....

Nov 28, 2011 | 1998 Toyota Camry

1 Answer

My keyless entry is not working. the lock switch in the car operates the locks just fine. my key fob has a brand new battery and the light blinks when I press the lock/unlock button. My vehicle is a 2005...


probably sensor for keyless entry,but would not advise u too get this from a junk yard as the sensors are vin specific,will put ur car into anti-theft mode then u will have to replace the body control computer,have a dealer order u a keyless entry sensor vin specific for ur car,these are usually under dash up top middle area its a little black box,will have to remove dash pad or dash to replace.

Aug 21, 2011 | 2005 Honda Civic

1 Answer

Ford 2000 excursion keyless entry not working


look online or go to the dealer and find a reprogramming procedure.

Mar 12, 2010 | 2000 Ford Excursion

1 Answer

Don't understand buttons on keyless entry remote fob.


If it is a factory remote it is either for the trunk release or the "panic" feature. Are the buttons not labeled?

Aug 13, 2009 | 2002 Toyota Corolla

2 Answers

Keyless entry wont work after battery died


stand at the vehicle and push and hold the lock and unlock buttons till the horn chirps to resync the key fob

May 03, 2009 | 2002 Pontiac Sunfire

1 Answer

2000 dodge neon alarm


This is what i found but you need one fob.

here is another way if you can get it done( i bevlieve) There is a box under the dash of your can it says keyless entry if you have the right box and the fab just plug and play.

Make sure you get the screws in the defrost vent there is some screws and then it there is snaps


http://shopping.msn.com/specs/keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor/itemid1124228415/?itemtext=itemname:keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor

Nov 15, 2008 | 2002 Dodge Neon

Not finding what you are looking for?
2002 Ford Excursion Logo

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...