Question about 2001 Hyundai Tiburon

Open Question

Etacs module for 2006 hyundia tiburon

Waiting on replacement remote .... how can I swich of anti theft so it stops resetting

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dsacco86
  • 1077 Answers

SOURCE: After replacing the battery I have no power at all

Possible causes:
1. New battery defective. ( Open circuit between battery cells ) Seen it before, therefore, possible.

2. Battery terminals not making connection ( check terminals )

3. Battery has different polarity than the original battery. ( Positive post and the negative post are reversed ) They do sell the reverse battery, therefore, possible. Basically, a battery hooked up backwards.
That would cause the Main fuse to blow resulting the no power in the vehicle.

Posted on Mar 30, 2009

  • 1 Answer

SOURCE: 2003 Hyundia Tiburon BCM

http://www.newtiburon.com/forums/showthread.php?t=102241&highlight=bcm

Posted on Jun 22, 2009

ghost45
  • 1280 Answers

SOURCE: Where is the ETACS unit on my 2007 Santa Fe?

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 03, 2009

  • 1 Answer

SOURCE: My 2004 Tiburon GT will not unlock with the

you can get it to crank but you just won't be able to use the keyless function without going back to the dealer first locate the ecu fuse in the fusebox under the dash, pull it out but don't put it down. Next put your key in the ignition and start turning over the motor, now the car won't crank or push oil through the motor with the ecu deactivated so don't hold it for too long. Now as your turning the motor over, reinsert the ecu fuse. The car will fire to life...you will have essentially reflashed your ecu so people with tuned ecu's beware. Your keyless won't work but hey at least now you can drive to get it fixed...as for the naysayers, yes I tried this on my tiburon and it still works fine so don't worry...good luck

Posted on Jan 21, 2010

BCAS1298
  • 3092 Answers

SOURCE: 2004 Hyundia Tiburon Battery replacement

Sounds like your alternator is bad, if car will stay running long enough to get over to an auto parts place where they can do an alternator test for free have it check or you can remove alternator and take it to them so they can test it. or with a volt meter start car remove jumper cables and check voltage at battery, should have no less then 13.5 volts, what your checking is alternator output voltage.

Posted on Jun 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intermittent start problem, what can cause this. No one can seem to find the problem.


Had same issue... Was a bad relay in the security anti theft system. Bang on module when trying to start should identify if that's it. Replacing module did the trick for me. It's a mechanic job as it requires reprogramming remotes

Aug 18, 2014 | 2006 Kia Sedona

2 Answers

Car will not start


You probably can't.
If the anti-theft module is in the cluster, you would need the correct key chip for the car the cluster came out of.
You might be able to bypass the passkey system by running a wire to the fuel pump relay and other components.
You may need a shop manual to find the circuits.

Aug 23, 2012 | 1997 Chevrolet Cavalier

1 Answer

Car won't start.Theft light blinks,clicking sound under hood and thumping like horn wants to go off.Seems like it's stuck in anti theft mode


anti theft light should blink every few seconds.

try disconnecting the battery for 15 minutes.

Anti-Theft-Perimeter The perimeter anti-theft system consists of the following components:
  • anti-theft indicator (THEFT)
  • remote anti-theft personality (RAP) module
  • hood switch
  • keyless entry remote transmitter
  • deck lid ajar switch
NOTE: The remote entry features will not function when the ignition switch is in the RUN or ACC position.
Up to four keyless entry remote transmitters (15K601) can be programmed at one time.
The keyless entry remote transmitters :
  • Are programmable.
  • Must be set at the same time.
  • House four buttons.
  • House three buttons (Mexico Anti-Theft System only).
Programming
Refer to Section 501-14B.
Inputs and Outputs
The remote anti-theft personality (RAP) module receives input from the following components for anti-theft operation:
  • Hood switch.
  • Deck lid ajar switch.
  • Keyless entry remote transmitter.
  • Power door lock switches (LH and RH).
  • Door courtesy input.
The RAP module distributes output to the following for the anti-theft system:
  • Power door unlock relay.
  • Power door lock relay.
  • Liftgate unlock relay (Wagon)
  • Park lamps relay.
  • HORN relay.
  • Dome lamp.
  • THEFT indicator.
  • Deck lid release.
Arming
The anti-theft system can be armed if:
  • The ignition switch is in the OFF position.
  • The panic alarm is off.
  • All doors are closed.
NOTE: If a door is open, the anti-theft system is prearmed and waiting for all the doors to be closed. The THEFT indicator will remain illuminated for up to 30 minutes waiting for all the doors to be closed. If a door remains open after 30 minutes, the THEFT indicator will turn off and the system will return to a disarmed state. After all doors are closed and the 30 second prearm (continuous THEFT indicator illumination) is complete, the system is armed.
NOTE: If the theft LED does not flash after 30 seconds, check the LED FLASH PID to see if the feature is enabled.
The anti-theft system will be armed when the lock button on the keyless entry remote transmitter is pressed, all doors are closed and 30 seconds have elapsed.
When the system is armed, the THEFT indicator will flash quickly until the system is triggered or disarmed.
Disarming
NOTE: Using a key in a door lock cylinder to unlock is not a valid method of disarming the anti-theft system.
Untriggered System
NOTE: If the driver arms the system and remains in the vehicle, an untriggered system can be disarmed by turning the ignition switch to the ON position.
An untriggered alarm system can be disarmed by pressing the unlock button on the keyless entry remote transmitter.
Triggered System
NOTE: If the hood or trunk are open when the system is armed, it must be closed and opened again before it can trigger an alarm.
An armed anti-theft system can be triggered by the following conditions:
The deck lid door, liftgate, hood or any door is opened using a key, inside door handle, hood release, etc.
  • The keyless entry remote transmitter can activate a panic alarm which is similar to the anti-theft alarm, but does not cause the THEFT indicator to flash.
A triggered alarm system can be disarmed by:
  • Pressing the unlock or panic button on the keyless entry remote transmitter.
  • Turning the ignition switch to the ON position.
Alarm State When Battery Power Is Cycled
When the RAP module is supplied power the first time at the vehicle assembly plant, the system will be in the disarmed state. The RAP module will remember whether it is armed, disarmed or triggered in its non-volatile memory. When the battery positive cable is removed and then reconnected, the system will return to the state it was in just before the battery was disconnected. If the system is in any prearm state, then the system will return to a disarmed state when the battery is disconnected and then reconnected.

Nov 06, 2010 | 1999 Mercury Tracer

1 Answer

Starts, runs 5 min. then shuts down everything, won't restart for couple minutes and with aid of jumper cables


does the truck have an anti-theft system? if so did u install anything new on the vehicle( stereo, remote starter etc...)if not then the module for the anti-theft my be toast. if u have installed anything new, double check where the wiring for the new component has been spliced, the anti-theft module needs at least a 5 volt signal in order 2 work. if this wire has been spliced then u will not have enough voltage to run the module properly.the module runs on a timer so if the truck stalls then u will have 2 wait about 5 mins for it 2 reset b4 u can restart the vehicle

Dec 10, 2009 | 2001 Isuzu Rodeo

1 Answer

2006 hyundia tiburon clutch slips bad when you put even a slight load on it


Usually when a clutch slips it need replaced. Take it to your mechanic. It will cost some bucks.

Sep 23, 2009 | 2006 Hyundai Tiburon

1 Answer

My 2002 sonata alarm wont shut off and my keyless wont stop it and the car also wont start with the key either


When the alarm is activated, there is an Anti-Theft device (Starter Kill Relay) which prevents anyone from starting the engine using the key (about 5 minutes). If you place the key in the ignition and turn the key to the "RUN" position, wait 5 minutes (approx), the engine should then be able to start. If not, the problem may be the ETACS (Electronic Time & Alarm Control System) module. If it does start, the problem may simply be that the battery in the keyless remote is weak/dead, or the remote needs to be programmed again for that vehicle. Only the remote can 'DEACTIVATE' the alarm. Best solution, take/tow the vehicle into a Hyundai Service Center (dealership), pay the diagnostic fee. They will tell you EXACTLY what the problem is and what's needed to fix it (parts, labor, tax, time-frame, etc.).
207eccf.jpg


Jun 14, 2009 | Hyundai Motor 2002 Sonata

1 Answer

Hello accent 2004 with anti theft system battery flat anti theft


Have you verified this system is running the battery down? The system you describe is called the Remote Keyless Entry System (Electronic Time/Alarm & Control System - ETACS Module). It cannot be 'disconnected' without disabling other systems (intermittent wipers, Chime bell, Door Warning, Dimming Off Room Lamp, Seat Belt indicator, remote power door lock/unlock system, etc.)

f92f17f.jpg

Jun 10, 2009 | Hyundai Motor 2004 Accent

1 Answer

Keypad reset. Now that I have the original keypad code, how do I change the code?


your owner manual tells you. Why not use the original code?

To change, here is 96 procedure, should be the same. please give good rating if this is what you want.

Entry Code The system (permanent) entry code is located in three places:
  • on the owner's wallet code card (in glove compartment)
  • electronically accessible by requesting the remote anti-theft personality module KEYCODE PID on the New Generation Star (NGS) Tester
  • on the remote anti-theft personality module housing
The remote anti-theft personality module is programmed at the factory with a five-digit entry code. A replacement remote anti-theft personality module includes replacement labels and a new owner's code card. To turn on the interior lamps and light all illuminated components:
  • press any button on the keyless entry keypad (14A626).
To program a temporary access code:
  • Enter the permanent code on the keyless entry keypad.
  • Press button 1/2 within 5 seconds of last digit of permanent code. (This alerts system to accept temporary code.)
  • Enter alternate five-digit code. Do not exceed 5 seconds between entering digits or between pressing the 1/2 key and entering the first digit.

Apr 08, 2009 | 1995 Ford Taurus

1 Answer

VEHICLE WONT START


Section 13-11: Anti-Theft System, Active 1998 Windstar Workshop Manual DESCRIPTION AND OPERATION Anti-Theft Alarm System NOTE: The system immediately monitors the ignition key lock cylinder upon removal of the key from the ignition. It is not necessary to arm the system for ignition key lock monitoring.

The anti-theft alarm system:
  • protects the vehicle from unauthorized entry into the passenger compartment, engine compartment and cargo area.
  • monitors the status of the ignition key lock cylinder.
  • is controlled by a remote anti-theft personality (RAP) module. The remote anti-theft personality module also controls the electronic door lock functions. Refer to Section 01-14B for more details.
  • when armed, detects unauthorized entry into the passenger compartment by using an input from the GEM module regarding the state of the door or liftgate (open or closed).
  • protects the engine compartment with a hood switch which is located on the LH cowl vent panel and is part of windshield wiper motor wiring (17A477) .
  • triggers an alarm if the ignition lock cylinder is forcibly removed from the steering column.
Once triggered, the system responds by:
  • flashing the low beam headlamps, the parklamps, rear lamps and the alarm indicator warning light emitting diode (LED).
  • sounding the horn (13832).
  • disabling the starter circuit until the system is disarmed.
---------------------------------------------------------------------------------------------
Remote Anti-Theft Personality Module
  • The remote anti-theft personality module is located behind the instrument panel (04320).
  • It contains a radio receiver that receives the RF signal from the keyless entry remote transmitter (15K601) through the alarm and lock system antenna (15603) and sends the appropriate command to the power door locks, the horn relay, or the generic electronic module.
  • The remote anti-theft personality module is equipped with an internal backup power supply which holds the programmed code in memory in the event the vehicle battery is disconnected.
-------------------------------------------------------------------------------
Remote Anti-Theft Personality Module Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove radio. Refer to Section 15-01 .
  1. Remove lower instrument panel center finish panel. Refer to Section 01-12 .
  1. Lower glove box.
  1. Remove two remote anti-theft personality module bracket retaining screws.
  1. Disconnect electrical connectors and alarm and lock system antenna (15603).
  1. Remove remote anti-theft personality module and bracket.
  1. Remove remote anti-theft personality module from mounting bracket.
Installation
  1. To install, follow removal procedure in reverse order.
  1. Tighten remote anti-theft personality module bracket retaining screws to 6-8 Nm (54-70 lb-in).

    34bdf35.gif
Components The system is composed of the following components:
  • remote anti-theft personality (RAP) module with integral antenna
  • alarm indicator LED
  • door lock cylinder switch RH, door lock cylinder switch LH
  • liftgate door lock cylinder switch (220A40)
  • hood switch (part of windshield wiper motor wiring (17A477))
  • ignition lock anti-theft switch (19A438)
The following vehicle components are also used by the anti-theft alarm system:
  • generic electronic module
  • power door lock switch (14028)
  • door open warning lamp switch (14018)
  • autolamp relay (14N089)
  • horn relay and bracket (13853) and horn (13832)
  • low beam headlamps
  • rear lamps (13404) and parking lamps (13200)
  • starter relay
  • door lock relays
  • keyless entry remote transmitter (15K601)
--------------------------------
Disarming an Untriggered System NOTE: A perimeter alarm will "shut off" after 165 seconds, but the system is still triggered and is not disarmed.

An armed but untriggered perimeter anti-theft system can be disarmed by one of the following four events:
  1. Unlock the doors by pressing the keyless entry remote transmitter (15K601) UNLOCK button once.
  2. Unlock any door with a key.
  3. Turn ignition switch to RUN or ACC.
  4. The remote entry PANIC button will disarm the anti-theft system only when the perimeter alarm is triggered and sounding.
------------------------------------------------
System Triggering NOTE: Although the remote entry PANIC alarm is not associated with the monitoring of the vehicle, the user will frequently say that the theft system was triggered when actually the keyless entry remote transmitter PANIC button was inadvertently pressed. A panic alarm will not flash the THEFT indicator.

The alarm can be triggered by the following events if the system has been armed and has not been disarmed first:
  • Open any door or liftgate.
  • Open the hood (16612) (if the hood was open when the system was armed, it must be closed before it can trigger the alarm).
  • Dislodge the ignition key lock cylinder.
  • The anti-theft system may be triggered inadvertently when the module is disconnected and then reconnected. To avoid inadvertent alarm triggering, disconnect the smaller 22-way connector first.
When the system is triggered the perimeter alarm will operate as follows: The remote anti-theft personality module will pulse the following outputs at approximately 1.3 Hz, 50 percent duty cycle for two minutes 45 seconds for North America. NOTE: Other perimeter alarms can be programmed for the system.

  • low beam headlamps
  • parking lamps
  • horn
  • THEFT indicator
The perimeter alarm can be retriggered, after a perimeter alarm has sounded for 165 seconds. After a perimeter alarm has timed out, if any trigger input is first seen as normal and is then seen in its trigger state, the perimeter alarm will be retriggered. The perimeter alarm can be triggered a total of three times between an arming sequence and a disarm event. An active panic alarm will be deactivated when a perimeter alarm is triggered (a perimeter alarm overrides a panic alarm).

Mar 02, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
2001 Hyundai Tiburon Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...