Question about Cars & Trucks

Open Question

Rane power steering service center

Power steering service center in KARNATAKA

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Are mil circuit (lights in center of dash i.e seat belts ,oil ,tire) defroster and steering wheel buttons circuit tied into one fuse or relay?


USA Market vehicles:

Check for your models FREE WIRING DIAGRAMS & TECH SERVICE BULLETINS at BBB Industries site
(registration required... real documents)


BBB Industries Premium Alternators Starters Power Steering Products

Jan 21, 2017 | 2007 Pontiac G5 Gt Coupe

2 Answers

Have 2008 chevy Malibu Ltz.past few days the dash will say "power steering "of course wheel gets tight. it's electric..not sure if the pump is going out or if it's the lines..how can someone tell?


The system can be scanned for faults, in the is case you need that test performed. The pump only runs when the computer control unit commands it to run it is on demand, this information comes from sensors in the system..

Dec 11, 2016 | Cars & Trucks

2 Answers

How much to replace power steering fuse on a chevy maiulb


Wrench light means you have a fault or service is due. Not sure what fault is . If it is a fuse the part cost is small, not sure about labour cost, it depends on where fuse is located but shouldn't take more than a few minutes. Hope this helps

Mar 04, 2016 | 2004 Chevrolet Chevrolet Malibu LT

2 Answers

How to add power steering fluid to 2008 pontiac g6


If you can't find a power steering fluid reservoir under the hood in the engine compartment your G6 could have Electronic Power Steering . If you look up under the dash below the steering column you will see a electric motor mounted to the steering column !
The power steering system reduces the amount of effort needed to steer the vehicle. The system uses the powertrain control module (PCM), body control module (BCM), power steering control module (PSCM), discrete battery voltage supply circuit, steering shaft torque sensor, steering wheel position sensor, power steering motor, driver information center (DIC), and the serial data circuit to perform the system functions. The PSCM and the power steering motor are serviced as an assembly and are serviced separately from the steering column assembly. The steering shaft torque sensor and the steering wheel position sensor are not serviced separately from each other or from the steering column assembly. The steering column assembly does not include the power steering motor and module assembly.

Jun 23, 2015 | 2008 Pontiac G6 Sedan

1 Answer

STEERING ISSUE


First, how's your power steering fluid level?
Is your power steering belt squealing?
If these questions don't fi the problem, you may have to bring to a service center (like Pep Boy's, or Town Fair Tire, some one you can trust) and tell them your problem!
Good luck.

Mar 06, 2014 | 2002 Dodge Durango

1 Answer

How to replace high pressure hose on a 1994 Silverado Chevrolet pick up truck.


hmmm..which high pressure hose the a/c or power steering hose...if its the a/c u need to take this to a service center. removing the high pressure hose without recovering the freon can cause serious injury.it is under extreme high pressure at all times even when the truck is not running... if its the power steering hose then start by removing the plastic shield in the steering staft at the steering box on the drivers side frame loosen the 18mm line nut then follow it to the other line nut on the back of the power steering pump....but sometimes the pump may need to be removed to to this, if this is the case i recommend u take it to a service center

Jul 12, 2011 | Chevrolet Silverado Cars & Trucks

1 Answer

Where is a power steering pump located on a 4 cylinder chevy cobalt ls


Your Cobalt is not equiooed with a Power Steering Pump. It has electric power steering. See the description below.

Power Steering - System Description and Operation
The electric power steering (EPS) system reduces the amount of effort needed to steer the vehicle. The system uses the body control module (BCM), power steering control module (PSCM), torque sensor, discrete battery voltage supply circuit, EPS motor, serial data bus, and the instrument panel cluster (IPC) message center to perform the system functions. The PSCM, torque sensor, not the EPS motor are serviced separately from each other or from the steering column. Any EPS components diagnosed to be malfunctioning requires replacement of the steering column assembly, also known as the EPS assembly.

Nov 20, 2009 | 2005 Chevrolet Cobalt

1 Answer

Where is a power steering pump located on a 4 cylinder in a 2005


Your Cobalt is not equipped with a Power Steering Pump. It is equipped with electric power steering. See the description below.


Power Steering - System Description and Operation
The electric power steering (EPS) system reduces the amount of effort needed to steer the vehicle. The system uses the body control module (BCM), power steering control module (PSCM), torque sensor, discrete battery voltage supply circuit, EPS motor, serial data bus, and the instrument panel cluster (IPC) message center to perform the system functions. The PSCM, torque sensor, not the EPS motor are serviced separately from each other or from the steering column. Any EPS components diagnosed to be malfunctioning requires replacement of the steering column assembly, also known as the EPS assembly.

Nov 20, 2009 | 2005 Chevrolet Cobalt

1 Answer

How to change the power steering on 96 ford explorer


Section 11-02C: Steering Gear, Power Rack and Pinion, Explorer 1996 Explorer with Power Rack and Pinion Steering Workshop Manual REMOVAL AND INSTALLATION Steering Gear SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Pitman Arm Puller T64P-3590-F
Removal
  1. Start engine.
  1. Rotate steering wheel from lock-to-lock (entire gear travel). Record n umber of rotations.
  1. Divide the number of rotations by two. This gives the required number of turns to place system in the on-center position.
  1. NOTE: Verify the front wheels and steering wheel are in the straight-ahead position.

    From the lock position, rotate steering wheel the number of turns determined in Step 3. This places the gear in the on-center position.


    Steering Gear, Explorer




  1. NOTE: Do not rotate steering column when intermediate shaft is disconnected or DAMAGE TO CLOCKSPRING will result.

    Remove bolt retaining the lower steering column shaft to the steering gear input shaft.




  1. Disconnect the lower steering column shaft from the steering gear.
  1. Remove stabilizer bar attachment from frame for clearance to remove gear.
  1. Unscrew the quick connect fittings for the power steering pressure hose (3A719) and power steering return hoses (3A713) at the steering gear housing (3548).


    Power Steering Hose Connections





    Item Part Number Description 1 3A674 Power Steering Pump 2 3A719 Power Steering Pressure Hose 3 3F780 Power Steering Cooler and Hose Assembly 4 3504 Steering Gear 5 5005 Frame
  1. Plug ends of fluid lines removed and ports in gear to prevent damage and entry of dirt.
  1. Remove two (2) nuts from P/S cooler.
  1. Remove P/S cooler from vehicle.
  1. Remove and discard the cotter pin retaining the nut to tie rod end (3A130) and remove nut.
  1. Separate tie rod ends from front wheel spindle (3105) using Pitman Arm Puller T64P-3590-F.




  1. Remove the two nuts, bolts, and washer assemblies retaining steering gear (3504) to front crossmember (5019).
  1. Remove steering gear from vehicle. If required, remove steering gear mounting bracket housing insulators (3F640) and steering gear insulators (3C716) from steering gear housing.





    Item Part Number Description 1 N807881-S60 Bolt 2 385935-S36 Washer 3 3F640 Steering Gear Mounting Housing Insulator 4 3504 Steering Gear 5 N800255-S60 Nut 6 5019 Front Crossmember 7 3C716 Steering Gear Insulator
Installation
  1. If removed, install steering gear mounting insulators into the steering gear housing.
  1. Push the steering gear mounting insulator and steering gear insulator in until there is no space between the lip on the insulator and steering gear housing.
  1. Position steering gear on front crossmember. Install nuts, bolts and washers retaining steering gear to front crossmember. Tighten to 128-172 Nm (94-127 lb-ft).
  1. Position power steering cooler onto bolts and install nuts. Tighten nuts to 68-92 Nm (50-68 lb-ft).
  1. NOTE: The fittings design allows the power steering pressure hose and power steering return hose to swivel when properly tightened. Do not attempt to eliminate looseness by overtightening, since this can cause damage to fittings.

    Connect power steering pressure hose and power steering return hose to appropriate ports on steering gear housing. Tighten fittings to 27-34 Nm (20-25 lb-ft).
  1. NOTE: Make sure the tie rod ends (3A131) are seated in the tapered spindle holes to prevent rotation while tightening nut.

    With the steering gear, steering wheel (3600) and wheel (1007) in the on-center position, attach the tie rod end to front wheel spindle and tighten to 56-76 Nm (77-103 lb-ft).
  1. If necessary, advance tie rod nuts to the next slot. Install cotter pins.
  1. NOTE: Verify that no rotation from the on-center position has occurred.

    Position steering column lower intermediate shaft over steering gear input shaft. Outer input shaft dust shield must be in place. Replace pinch bolt and tighten to 41-56 Nm (30-42 lb-ft).
  1. Replace the front wheel and tire assemblies. Refer to Section 04-04 .
  1. Replace wheel covers.
  1. Lower vehicle.
  1. Refill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F.
  1. Purge air from steering system. Refer to Section 11-00 . Verify absence of any unusual power steering noise.
  1. Check and adjust toe alignment specifications. Refer to Section 04-00 .
  1. Make sure steering gear operates correctly and is not leaking.
  1. Check and adjust fluid level in power steering oil reservoir.

Jul 10, 2009 | 1998 Mercury Villager

1 Answer

When turning the vehicle started making a whining noise


Yes it is low on power steering fluid. Go to any service center and watch them put it in. This way you know in case it happens again. Good luck

Mar 30, 2009 | 2005 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...