Question about Cars & Trucks

Open Question

What's size wrench do you need to remove fan clutch bolt on 2006 jeep commander

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torqe specs for 2006 H3 fan/clutch and water pump


special tools you need EN 48543 FAN CLUTCH HOLDING TOOL. J41240 FAN CLUTCH REMOVER AND INSTALLER. TORQUE FOR FAN CLUTCH NUT 41 LB FT. FOUR BOLTS TO FAN BLADE TORQUE 20 LB FT.WATER PUMP BOLTS TORQUE TO 11 LB FT. DONT NEED SPECIAL TOOLS REMOVE WATER PUMP.

Nov 29, 2012 | 2006 Hummer H3

2 Answers

How do i remove the fan and pulley on a 1987 ford ranger 2.9 v-6?


The question is: How remove clutch in order to remove fan mounted on its engine-side face.
  • Generally, the clutch drive half shaft must be uncoupled from coolant pump (impeller drive) half shaft using special wrench kit available as loaner from AutoZone (free with $79 approx deposit).
  • Best done after shroud & radiator remove after coolant drained.
  1. Uncouple coolant pump and fan clutch drive shaft(s) as follows:
    1. span across combo-pulley-sheaves-unit mounting bolt heads with large tool kit wrench, and
    2. span inline clutch coupling nut with small tool kit wrench. Then,
    3. turn small wrench (and coupling nut) CW while resisting with large wrench (CCW) to turn coupling nut until disengaged from coolant pump drive shaft.
  2. Remove fan/clutch assembly.
  3. Note direction of mounted fan hub and fan blades orientation to ensure proper re-assembly.
  4. On rear of clutch assy, remove 4 bolts to disengage and remove fan.
  5. Assemble new fan to clutch (or, preferably, new clutch and new fan) using new bolts and washers provided with fan.
  6. Couple fan-clutch assy to coolant pump drive shaft as per opposite of uncoupling step 1, above. (Turn inline nut CCW to tighten...30 ft-lb.
  7. Check that fan can be hand turned...CW.)
  8. Rest shroud over and onto fan.
  9. Replace radiator; remount shroud; reclamp hoses, and refill and air purge cooling system.
remove-fan-pulley-1987-ford-ranger-2-9-v-2cg35myhodwcq1awmwat24pw-4-0.jpg

Aug 12, 2012 | 1987 Ford Ranger

2 Answers

Ford ranger fan clutch


There may be a tool, or you jam a metal tool between two metal parts.
check these out:


Removing Stubborn Clutch fan Ranger Forums The Ultimate Ford Ranger...

Fan clutch removal


Apr 11, 2017 | 1993 Ford Ranger SuperCab

1 Answer

HOW TO REPLACE CLUTCH FAN


to remove clutch fan you need to remove upper fan shroud, you need large wrench to remove the fan clutch retaining nut to remove fan and clutch away from the engine drive belt should keep pulley from turning while loosen fan clutch retaining nut.if pulley belt turns while loosen fan clutch bolt remove drive belt use strap wrench hold pulley while you remove fan clutch bolt this procedure for checvrolet if you working on volkswagon you need spanner wrench hold the idler pulley while you use large wrench to loosen the large drive nut to fan clutch. you have to remove fan with clutch from engine then you can remove clutch from fan you can go to auto parts stores rent a spanner wrench try auto zone they rent out tools.

Jan 05, 2012 | Cars & Trucks

1 Answer

How to remove a water pump


Locate water pump.. It's where the bottom radiator hose goes from the radiator. Remove any brackets or parts that are in your way. Remove water pump! Reverse procedure for installation. You have to remove the fan clutch from the water pump shaft and lift the shroud, fan and clutch all out together. remove two bolts in the center radiator support which let the radiator move forward an inch or so, loosen the fan from the clutch for a little more wiggle room to get it out. The shroud will have rubber splash shields hooked to the lower sides too, so be sure to unhook them or you will tear out the holes in the rubber shields.The fan clutch has to come off anyway because it's attached to the water pump. You don't need to remove the fan shroud. Just take out two bolts on the fan clutch and loosen the other two so you can push the clutch back a little (DON'T let the fan clutch fall). Then remove the water pump. It's a little tight, but much easier than removing the fan shroud.the only specialty tool that you will need is the water pumpt "grab" tool and the fan clutch wrench. These two items come together in one kit that you can rent from the Auto Parts store.
The "grab" tool holds the water pumpt pully firmly while you rotate the fan clutch retainer using the fan clutch wrench.

DO NOT attempt to use a break over bar or some other home-grown tool to hold the water pump pully while attempting to break the fan clutch free - you will mess up the heads of the four retainer bolts holding the pully to the water pump face.
this will help.thanks.

Feb 21, 2010 | 2006 GMC Envoy

1 Answer

Need to rep lace water pump on 1995 jeep cherokee straight six


START BY TAKING OFF THE FAN SHROUD. I BELIEVE THAT IT IS HELD ON BY A COUPLE OF BOLTS. THEN USING TWO WRENCHES, TAKE OFF THE FAN. THE BEST WAY TO DO THIS IS TO TAKE THE TWO WRENCHES AND USE ONE TO APPLY PRESSURE IN TH OPPOSITE DIRECTION SO THAT YOU CAN LOOSEN THE OTHER BOLTS WITHOUT THE FAN TURNING. REMOVE THE FAN CLUTCH. REMOVE THE BELT FROM THE PULLEY. REMOVE THE FAN HUB. THIS WILL ALLOW YOU TO BE ABLE TO GET TO THE WATER PUMP BOLTS. ALSO TAKE OFF THE RADIATOR HOSE GOING TO THE TOP OF THE RADIATOR AND THE OVERFLOW TUBE. INSTALLATION IS THE REVERSE OF REMOVAL.

Feb 17, 2010 | 1995 Jeep Cherokee

2 Answers

I am trying to remove the bolt for the fan clutch assembly on a 97 chevy blazer.


  1. 1 Remove the fan and clutch assembly from the fan's pulley. The assembly attaches to the pulley with several bolts on the circumference of the pulley. To remove the bolts, position an open-end wrench over each bolt and turn each bolt in a counterclockwise direction while grasping one of the fan's blades to prevent the fan from turning with the bolt.
  2. Step 2 Pull the fan and clutch assembly away from the engine, then lift the assembly out of the engine's compartment.
  3. Step 3 Remove the bolts which hold the fan to the clutch. The bolts are located on the back of the fan, and can be removed with a open-end wrench.
  4. Step 4 Place the fan and clutch assembly on a flat surface with the clutch facing up, then pull the clutch straight up to disengage it from the fan.

Nov 12, 2009 | 1997 Chevrolet Blazer

1 Answer

Removing the fan clutch


get a big adjustable wrench and insert it in the bolt and hammer it fast in one blow that should solve your problem

Jun 04, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Fan bolt cant loosen


they can be hard they sell a fan wrech special set up but it usally slips. put the right size wrench (its big) on the nut and from the front of the vehicle wack the wrench with a hammer tword the passengers side of the vehicle Leave the belt on to help with tention

Feb 07, 2009 | 2000 Jeep Grand Cherokee

2 Answers

04 trail blazer


there is a big nut that is part of the fan clutch that unscrews from the water pump .I use a long punch to break it loose then a big adjustible wrench.

Aug 25, 2008 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...