Question about Cars & Trucks

1 Answer

1993 eclipse 2.0 non turbo crank angle senser where is the notch that alines with punch mark

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

To install:

  1. If the timing is not disturbed, perform the following procedures:
    1. Install a new housing O-ring and lubricate with clean oil.
    2. Install the assembly in the engine so the coupling is aligned with the matchmark on the housing and the housing is aligned with the matchmark on the engine. Make sure the sensor assembly is fully seated and the shaft is fully engaged.
    3. Install the hold-down nut.
    4. Connect the harness connector.
    5. Make sure the sealing O-ring is in place, install the cap and tighten the screws.
    6. Connect the negative battery cable.
    7. Adjust the ignition timing, if applicable, and tighten the hold-down nut.

  2. If the timing is disturbed, perform the following procedures:
    1. Install a new housing O-ring and lubricate with clean oil.
    2. Position the engine so the No. 1 piston is at TDC of its compression stroke and the mark on the vibration damper is aligned with 0 on the timing indicator.
    3. Install the sensor in the engine so the factory matchmark on the coupling (notch) is aligned with the matchmark on the housing (punch mark) and the housing is aligned with the matchmark on the engine. Make sure the sensor assembly is fully seated and the shaft is fully engaged.
    4. Install the hold-down nut.
    5. Connect the harness connector.
    6. Make sure the sealing O-ring is in place, install the cap and tighten the screws.
    7. Connect the negative battery cable.
    8. Adjust the ignition timing, if applicable, and tighten the hold-down nut.


2.0L Non-Turbo Engines
See Figure 3
  1. Disconnect the negative battery cable.
  2. Detach the crankshaft position sensor electrical connector.
  3. Unfasten the retaining bolt, then remove the sensor.



1993 eclipse 2.0 non turbo crank angle senser wher - 0900c152800ad846.jpg enl1993 eclipse 2.0 non turbo crank angle senser wher - enlarge_tooltip.gifs=enlarge_tooltip.gif

Fig. Fig. 3: Location of the crankshaft position sensor-1997 2.0L non-turbo engine shown

Posted on Apr 24, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Saaboheme
  • 76 Answers

SOURCE: 1993 saab 900 belt diagram

Sorry, I don't have access to a Bentley now. There are 4 belts, 2 for alternator etc, 1 for aircon and 1 for pwr steering.
The power steering belt goes round the power steering pump & crank pulley only.
The paired belts go round crank pulley, alternator and water pump.
The aircon belt goes round crank pulley, aircon compressor and tensioner.
Alternator / water pump pair are closest to the engine.
Power steering is in the middle (with aircon) or closest to the bulkhead (without aircon).
Aircon (if fitted) is closest to the bulkhead.

(1) If you do not have an AC compressor, skip this step and go to step 2. If you dohave one, begin by cutting any cable ties that hold the main wiringharness to the AC hoses. Lift the harness up and over onto the camcover until it's near the PCV valve, and is now out of your way.

All nuts & bolts in this step are 13 mm.

Then, slacken the 2 bolts attaching the AC tensioner pulley mount (athick triangular steel plate) to the head. Use a long box wrench (ringspanner, in Englishicon_cheesygrin.gif ).

Using a deep-wall socket (or an offset ratchet wrench, or plain wrench)on the adjuster nut, back it off until there's no more tension in thebelt (you won't be able to remove the belt yet, though).

Now, remove the upper of the 2 mounting bolts and its washer, and pivot the tensioner down; remove the belt.

Remove the lower bolt, and lift out the tensioner. Look the triangularplate over for cracks, and spin the pulley to see if its bearing issmooth and quiet. (If you find problems, the pulley is about $15 and www.eeuroparts.com sells the entiretensioner assembly for something like $70.) Back off the adjuster nutuntil it's about 1/4" (1/2 cm) from the end of its threaded rod (usevise-grips to clamp the rod's other end onto the triangular plate, orput the whole thing in a vise).

(2) Slacken the bolt and nut holding the power steering pump to thehead and to the RH engine mount, respectively. Slacken the adjuster nut(yes, anotherthreaded-rod type thing) by about 1/2" (1 cm). You can use a normalwrench for this, but it takes forever--so I made a special tool bytaking a cheapo 13 mm open-jaw wrench and bending it to a 45-degreeangle just below the jaws (cut it to length if it's too hard tomaneuver). Loosen the mounting nut until it's almost off (but not completely off,or you'll lose the bolt it screws onto--this bolt was designed to fallout when the nut is removed). Pull the nut end of the threaded rodtowards the firewall to get it of the adjuster fork. Push the pumptowards the engine centerline and pull its belt off (you may need topry with a screwdriver to get it out of the pump pulley completely).

(3) Slacken the 16 mm nut on top of the alternator. Back off the alt.adjuster's 10 mm nut about 1/2" (1 cm)--a ratcheting wrench helps here.(This is the last threaded rod--I promise.) Completely remove the 16 mmnut, and pull the adjuster towards the firewall until it's out of thealt.

Now for the clever part: Cut yourself a wedge from a piece of wood (2 x4 is perfect), with a rise of 3" (8 cm) and a run of about 12" (30 cm).Push the alt. towards the engine, and shove the wedge in between theside of the alt. and the coil-spring tower (master cylinder mountingbracket works, too). Keep pushing the alt. and driving the wedge downuntil the alt. is so close to the engine that it's compressing thelower heater hose.

Pull the outer belt off the alt. pulley. Working from the RH side ofthe car, lift the belt off the water pump pulley and then disengage itfrom the crank pulley. Now, pull the inner belt into the outergroove of the water pump pulley. Go back to the LH side of the car, andmove the inner belt into the alt. pulley's outer groove. Try removingit from this pulley; if too difficult, either wedge the alt. closer tothe engine or try pulling the belt off the water pump pulley from theRH side of the car (a helper is very useful for all this).

(4) Install the new inner belt by fitting it into its groove in thecrank pulley first. Work it into the outer grooves of the alt. andwater pump pulleys, then into the inner ones. Install the outerbelt--again, first onto the crank pulley, then the water pump and alt.pulleys.

Remove wedge. Insert tensioner into alt. making sure the threaded rodsettles into its fork, and refit its 16 mm nut--but don't fully tightenit yet. Tighten 10 mm adjuster nut until belts can be pushed in only1/2" (1 cm) by thumb pressure (applied 1/2 way between water pump andcrank pulleys).

(5) Push PS pump as close to engine centerline as possible, andfinger-tighten its mounting bolt to hold it there. Fit a new beltaround the crank pulley first, then work it into the pump pulley groovefrom the bottom of the pulley until it pops in. You may need to use both hands, and/or carefully pry the belt on with a screwdriver.

Loosen the bolt you just tightened. Pull the pump away from enginecenterline, insert threaded rod into its fork (you may have to back theadjuster nut off some more), tighten the mounting nut (but notcompletely), and screw in the adjuster nut until the belt deflects asdescribed in (4) above.

(6) Start the engine. Blip throttle, watching the belts deflect as theengine speed goes up and down. If the "blur" you see midway down eachbelt is over 1" (2 cm) wide, tighten the belt(s) until it isn't. Tighten the PS pump mounting nut and bolt, and the 16mm nut on the alt.

If your car doesn't have AC, your belt replacement is over!

(7) If you haveAC, reattach the tensioner to the head with the lower bolt only (andleave this bolt finger-tight). Fit the new belt around the crankpulley, then around the compressor pulley and, finally, around thetensioner.

Reinstall the top tensioner bolt and its washer. Be careful and patienthere--you're threading a steel bolt into aluminum, so make sure it goesin straight. You may have to back off the tensioner nut a little. Leavethis bolt finger-tight.

Screw in the adjuster nut to get the deflection as described in (4)above. Start the engine, and blip the throttle. Watch belt's "blur" on LHside of engine. Adjust as in (6). Switch on compressor, and repeat.

If satisfied, tighten the 2 tensioner bolts. Return wiring harness toits original position, and re-secure with cable ties if needed.

Posted on Dec 16, 2008

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

sk8rdude_88
  • 27 Answers

SOURCE: need the vacuum hose diagram for a 1998 mitsubishi eclipse

http://www.dsmtuners.com/forums/attachments/420a-bolt-tech/89827d1228187918-resolved-need-vacuum-line-help-fast-420aturbovac-boostlinesstock.jpg
hope this helps

Posted on Oct 21, 2009

  • 1757 Answers

SOURCE: isuzu trooper 2002 RLV engine. camshaft timing

Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams and Photos with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams, instructions and photo's for use.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2002/make/isuzu/model/trooper/2002_isuzu_trooper_timing_belt_diagram_marks.htm

Posted on Mar 25, 2010

jturcotte
  • 8190 Answers

SOURCE: 2001 2.4l turbo timing marks see marks on cam

everything is at 12 o'clock. see diagram from autozone.com

1515ac4.gif

Posted on Sep 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 96 Mitsubishi Eclipse 2.0 Non turbo change timing belt Everything's working I cannot get it to start that acts like it wants to start but it won't I don't know what else to do please help


I can try to help you. Did you unpin the tensioner? Rotate, by hand the crank, at least revolutions, and then check the cams and crank to oil pump timing marks still line up? It doesn't take much to throw them out.

Dec 05, 2015 | Mitsubishi Cars & Trucks

1 Answer

Left fan wont turn on my 1999 eclipse 2.4 non- turbo


Try to change the temp switch.could also be the control module

Nov 17, 2012 | 1999 Mitsubishi Eclipse

1 Answer

I have a 1997 Mitsubishi Eclipse Gs non turbo that has a water outlet that has been pitted and needs replacing. I cannot find the outlet for the non-turbo. Any suggestions?


Your problem is most likely because you are describing your vehicle as a "Gs". The only similar listings in the catalog are for a "GSX". (The parts counter person probably has no clue that there is a difference) The GSX is only built in a turbo version, therefore you will not find a water outlet for the non-turbo version...it simply does not exist.

Now, if you simply describe it as an Eclipse, there are water outlets listed for the turbo 2.0L, the non-turbo 2.0L and the non-turbo 2.4L engines. You did not bother to mention engine size, so I will list the part numbers for BOTH of the non-turbo engines.

For the 2.4L engine: Compressor Works Part Number 815517

For the 2.0L engine: Compressor Works Part Number 815576

Both are available from AutoZone

Apr 17, 2011 | 1997 Mitsubishi Eclipse

1 Answer

Timing marks for the Dodge 2.4L caravan, 2000


To align both sets of timing marks, turn engine crankshaft to the right with belt on cam and crank. Once you have done this the crankshaft alignment mark (on front of crankshaft gear) will line up with mark to the rear of gear on engine block.The two cam gear timing marks should be alines across from one another. The right cam gear is the intake side and the left side is the exhaust side. After removing the belt turn the exhaust cam down 1/2 notch. Timing mark on exhaust 1/2 notch down from the intake side. Install new belt and recheck everything to make sure it's all correct. Hope this will help you.

May 16, 2010 | 2000 Dodge Caravan

1 Answer

1993 subaru legacy (non-turbo). I am not getting a spark. I replaced the plugs, wires, coil, cam sensor, and crank sensor. The car will turn over but not start. I checked the codes via service engine soon...


check 2 see if you have power going 2 your cam and crank sensors. if you do make shure the wires havnt poped out a bit... if you have no power there you will have 2 trace the wiring too see if there is a lose connection...

Aug 31, 2009 | 1993 Subaru Legacy

1 Answer

Motor swap


If your planing on swaping the 2.0 non-turbo(420a) to the 2.0 turbo(4g63t) your problem will be that the motor and transmission are on opposite side of one another. My GST has the trans on the passenger side and the motor on the driver. The 420a is just the opposite. If your serious about it you should get the motor rebuilt with higher performance crank, pistons, rods, exc.  And they make turbo kits for the 420a.  But you'll need better fuel delivery and some mild tuning.

Dec 23, 2008 | 1997 Mitsubishi Eclipse

2 Answers

I have a 1995 mitsubishi eclipse, 4 cylinder, 2.0 non-turbo. The car will crank but there is no spark and we are not getting any gas. We've checked all of the fuses and the relays. Do you have any...


if you haven't checked the ASD relay, make sure its working.
175c874.jpg if thats okay, check the Cam Angle and Crank Angle sensors. if it isn't any of those, its probably the ECU

Jul 22, 2008 | Mitsubishi Eclipse Cars & Trucks

2 Answers

Can i bplt up a eclipse 2.0L 420a non turbo to a 95 eagle talon non turbo


yes. they are exactly the same.

NOTE:
  • the 95-96 year models, have a few sensor plugs that are different than the 97-99 models. such as the coil pack and the cam angle senor.

Jul 21, 2008 | 1994 Eagle Talon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...