Question about Mitsubishi Pickup

1 Answer

Accessing front driveshaft bearings on mitsi L200 4x4 1999

There is a clunking noise like a bottIe is in the tray except its comin from the front wheel. the driveshaft bearings seem worn but i cant get at them. I can get the hubs all off but the disc brake bolts jus spin and wont shift. there doesnt seem to be any bolts that i can get at. is there a special trick of tool i need to get it all apart?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

If you get the outer hub off, there is a big locknut and snap rings holding the rotor and bearings in. There is a nut on the back side of the rotor is why they are spinning.

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Loud humming noise


Could be carrier bearing(s), worn gears, or bad driveshaft joints.

Jul 18, 2016 | Cars & Trucks

1 Answer

Loud grinding/clunking noise when driving, lessens when I press the brake


Loud Noise Unknown Origin - Ask the GM Technician - GM-Trucks.com

www.gm-trucks.com > ... > Ask the GM Technician

Jun 30, 2006 - 7 posts - ‎3 authors
I get a loud clunking, grinding noise while turning to the right only, and ... I moved the passenger side tire to the rear driver side just in case it ...

can bad wheel bearing/hub cause loud clunking noises?

www.jeepsunlimited.com/.../showthread.php?...loud-clunking-noises

Nov 12, 2009 - 14 posts - ‎6 authors
driving home, i noticed some metal clunking sounds coming from the front driversside. at ... hmmmm....if it's grinding, then probably a bearing.

Front Clunking sound when driving straight. - TDIClub Forums

forums.tdiclub.com > ... > VW MKIII-A3/B4 TDIs
Dec 21, 2011 - I have a sporadic clunking noise from the drivers side front end. '98 jetta ... If I try to coast it gets really louder and more pronounced. ... whirring orgrinding could be several things: wheel bearing, brake pads due to a caliper ...

Quick Guide to Diagnosing Differential & Driveline Noises ...


Dec 26, 2015 | Cars & Trucks

1 Answer

Can the drive shaft bearing being bad make some kind of howling noise?


Any howling could be any bearing. I would go slow and quiet while holding the brake and pulsing the gas to listen for a bearing clunk. A driveshaft will also thump with play if you switch between forward and reverse while stopped. Don't forget that on a front or all wheel drive vehicle the drive axle is a driveshaft. I wouldn't drive it around like this either because if it breaks you're in big trouble.

Mar 08, 2015 | Cars & Trucks

2 Answers

2003 ford sport trac front grinding noise from drivers side when sharp left turn


go to the magicmechanic website and send him this--hes the best there is and will rply

Jan 19, 2015 | 2003 Ford Explorer Sport Trac

2 Answers

Clunk at rear when starting from braking


clunk noise when coming to a stop could be driveshaft slip yoke binding.clean lubricate driveshaft slip yoke or slip yoke bearings could be worn.

Oct 19, 2012 | 2008 Chevrolet Trailblazer

1 Answer

REPEATLY worn out carrier bearing on my 2001 GMC Sonoma extended cab ( 4.3 , 4speed auto 2wd) what could be the cause of this even after I've had it rebalanced?


  • If the bearing fails and seizes up, the rubber will be torn away from the bearing. The seized bearing can tear away the rubber mount that supports the outside of it allowing the bearing to rotate with the driveshaft. This allows the driveshaft to wobble up and down causing a vibration.
  • The rubber can also deteriorate due to age or contamination with oil. The driveshaft will operate at the wrong angle and vibration or noise will result. The vibration occurs most often during hard acceleration.
  • A worn center support bearing can cause a whining sound that varies with vehicle speed. The noise is constant in pitch, rather than changing or intermittent like U-joint noise.
  • If the truck has been raised , the alignment of the drive shaft will also change, A damaged driveshaft can exhibit a variety of symptoms. A clunk that is heard when the transmission is shifted into gear is the most obvious. You can also encounter unusual noise, roughness, or vibration.
    NOTE The engine, torque converter and driveshaft change in frequency as rpm changes. A rebuilt torque converter is often the cause of a vibration that is rpm-related.

    To help differentiate a potential drivetrain problem from other common sources of noise or vibration, it is important to note the speed and driving conditions at which the problem occurs. Unfortunately, it is often difficult to accurately pinpoint drivetrain problems with only a road test. Expand the undercar investigation by putting the vehicle up on the lift, where it is possible to get a good view of what is going on underneath.

    • Check the companion flange, carrier bearing, pinion shaft seal, and pinion bearing, transmission's extension housing seal and bushing, and the u-joints.
    • Check the driveshaft for runout, or the amount that a part wobbles up and down or side to side when it is in motion.

Sep 23, 2011 | 2001 GMC Sonoma Extended Cab

1 Answer

I replaced the right side front axle on my 2000 blazer and I still get a clunking noise when I switch into 4 wheel drive the noise only happens when I press on the gas so I believe it has something to do...


look for loose disconnected rear suspension components.also check for loose driveshaft bolts.inspect all nuts bolts to the specified torque.if everything check out okay.you have worn or damaged universal joint bearings.

Dec 27, 2009 | 2000 Chevrolet Blazer

3 Answers

Whining/grinding noise at deceleration


We have the same problem at our shop. We haven't rebuilt the front differential yet. We tried 3 different shafts on 2 different Jeeps and the noise is on both just the same. By greasing the front driveshaft cv joint, we got he noise to quiet some, but it is still way to loud. With the driveshaft out, the noise is gone. We are about to buy a new shaft from the dealer for $600. There are some service bulletins about some noisy driveshafts.

Jun 15, 2009 | 2009 Jeep Grand Cherokee

1 Answer

Chevy blazer runs funny in 4 wheel drive


Hello,
Be sure that the joints on your front driveshaft are in good condition, hope this helps, good luck

Apr 03, 2009 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...