Question about Cars & Trucks

Open Question

Shock sensor on my 94 camry

Hi my engine check light is on,,the guy i got it from said it was the shock sensors by the tappet cover/s under the intake cover,is this true & what do they look like please

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: 98 ford f-150 temp gauge and light problems

the intake air temperature sensor is located inside the air intake duct which is where the air filter is located pull the rubber tubing off the throttle body and look inside with a light and you will see it

Posted on Jan 09, 2009

Ad
daves944
  • 1050 Answers

SOURCE: Need to find Mass Air Flow sensor on 98 Camry

You are not stupd! :-) This car has a speed-density system. The computer is programmed to meter fuel and spark timing from manifold absolute pressure (MAP), engine temperature, air temperature, and throttle position only.

Are you having a problem?

Posted on Mar 29, 2009

  • 1 Answer

SOURCE: 2003 Toyota Camry Se V6 has a check engine light

I had the same problem, then took my car to an expert repair shop who diagnosed the sensors and
found no problem with the car. They notified the DMV who was unaware of the problem, who then told the repair shop (John's Bascom Automotive) that they will adjust their computer system to allow a "two speed idle test". My bill was $95 and I still have to pay for a smog test after driving around for
a couple of days to clear the computer monitors, a fair amount and I gladly paid it.

John advised me that I'd get no satisfaction with Toyota or the DMV. I went to the dealership where I
bought the car and they said that the smog stations don't know what they're doing. They charge
about $100 and work around the P0500 code but it takes them about two hours to do this. I told
them that I should have been notified about the dyno none-compatability by Toyota and that Toyota
should have notified the DMV beforehand. I wonder how many speed sensors are being replaced by
unknowing smog shops around the state. I got Toyota's main customer support phone number and
will call them Monday. I'm going to get my pound of flesh ($95 worth) from the DMV next week also.

traderralph

Posted on Jun 26, 2009

outdoorsman5
  • 631 Answers

SOURCE: Vaccum hose diagram for 97 chevy tahoe 5.7 liter

I have the diagram you need. If you send me your email I will scan it off and send it to you. outdoorsman592003@gmail.com

Posted on Sep 12, 2009

ginko
  • 19396 Answers

SOURCE: where can i find the

Hi.

The thermostat housing is built in with the water inlet pipe. The pictures below show the thermostat in different engines used in Camry from the same year:

ginko_330.gif

ginko_331.gif

ginko_332.gif

Posted on Sep 20, 2011

Testimonial: "thanks a lot"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is map sensor located on a 94 Cadillac DeVille 4.9 engine


Under hood, center, rear engine area, above valve cover, mounted in bracket.

From autozone.com:

Manifold Air Pressure Sensor

Fig. MAP sensor specifications-note how altitude and pressure affect the voltage readings
REMOVAL & INSTALLATION

  1. Remove the intake manifold top cover.
  2. Disconnect the crankcase breather tube from the throttle body.
  3. Remove the MAP sensor from the intake manifold.
  4. Detach the MAP sensor electrical connector.
  5. Inspect the MAP sensor grommet for wear or damage and replace as needed.
To install:
  1. Installation is the reversal of the removal procedure.

map-sensor-located-94-cadillac-deville-3yvs1abwdo3hwax2tll0gwig-1-0.jpg

Feb 14, 2016 | Cadillac Cars & Trucks

3 Answers

My 94 Toyota Camry 4 cyl is running really rough and stalling out once the engine warms up


1. Error Code 24. Intake Air Temperature Sensor.
Solution:
Check the following:
- IAT Connector and wiring.
- Intake Air Temperature Sensor.
- Engine Coolant Temperature Sensor.
- ECM.
2. Rough Idling when the engine is hot.
The following are the reasons due to which the engine can perform bad when it is hot.
- Fuel pump control circuit.
- Fuel pump pressure.
- Fuel injectors.
- Non Return Valve clogged, located on the lower side of car chassis above the fuel tank.
- Engine compression, valve clearance, spark plugs.

Apr 14, 2014 | 1994 Toyota Camry

2 Answers

My 94 Toyota Camry LE is running really rough and stalling.


The previous owner has screwed things up by changing the air intake and eliminating the air temp sensor. The car's computer depends on a series of sensors to determine what fuel mixture it should command, and now it can't do that properly.

When the car is cold, it knows from the coolant temp, and it sends plenty of fuel, but when hot it is getting the mixture wrong.

Restore the air intake to original, with the correct sensors, as it should run OK.

If not, then go looking for a vacuum leak or an air leak in the air intake hose and plenum somewhere.

Mar 05, 2017 | 1994 Toyota Camry

1 Answer

Knock Sensor


Hi. its somewhere under the intake manifold. quite painful to access.

Feb 04, 2014 | 1999 Toyota Camry

1 Answer

Have a 94 toyota camry , check engine light comes on when stop at light or car sits at idle. got codes 12 , 22, am very confused !!


Code 12. RPM signal.
Problem area: Loose connection, broken rpm signal wire from distributor to ecm to rpm meter, rpm meter, distributor assembly or ecm defective.
Code 22. Water temperature signal.
Problem area: Loose connection at water temperature sensor connector, broken wire between the sensor and the ecm, defective sensor or ecm.

Aug 25, 2013 | 1994 Toyota Camry

1 Answer

1993 Toyota Camry v6, engine cranks, will not start. No spark at plugs


check all your conectors including distribuitor, if none lose remove distribuitor cap an coil cover and inspect for cracks or carbon trace, both cap and coil if any replace distribuitor.

Jul 28, 2012 | 1993 Toyota Camry V6

1 Answer

Where can i find the cooling system sensor on my 94 camry csi? also i have an oil leak under engine driver side. maybe only 4 or 5 drips overnight


Hi.

The thermostat housing is built in with the water inlet pipe. The pictures below show the thermostat in different engines used in Camry from the same year:

ginko_330.gif

ginko_331.gif

ginko_332.gif

Sep 20, 2011 | 1994 Toyota Camry

1 Answer

Understanding trouble codes for my vehicles


first the quest, this is common for nissan, replace the knock sensor, this sensor is located under the intake manifold rear of engine, some models you can sneak sensor out without removing the intake, this will take care of that car. now the camry, im guessing this is a 4 cylinder engine, replace the air fuel sensor (oxygen sensor) thats on the exhaust manifold. this will solve that problem. hope this helped.

Jan 25, 2010 | 1999 Toyota Camry

1 Answer

Toyota Camry Knock Sensor Problem The top of the radiator on my 1993 3.0 lt Toyota Camry V6, 3VZ FE engine split some months back and it overheated. I have since sorted out the head gaskets and it seems to...


Hello. You have posted an excellent question.

The code 55 you are getting, in Toyota terms, as as follows:

"No number one knock sensor signal to the ECU fo four crank revulutions under these 2 conditions: Coolant temperature 140 degrees F or more; Engine speed between 1600 and 5200 RPM."

This indicates a failed (or a loose) knock sensor on the Right Bank of the engine. Since the knock sensor is basically a piezo-electric crystal, not continuity test can be performed with the intake manifold installed.

You can check the continuity form the Knock Sensor wires to the ECM, but, this may not prove useful to you.

Unfortunately, you are going to have to pull the intake, and check the knock sensor wiring integrity. If the connector is good, and the sensor is tight, I would suggest replacing the sensor. Actually, if you were in my shop, I would suggest replacing them both, as the whole intake will have to come off if the other sensor fails. Better to replace them both at once, than to pull the intake again.

We here at FixYa hope that this helps you out, and saves you some future reoair dollars. Thanks for choosing FixYa for advice.

Jan 08, 2010 | 1993 Toyota Camry V6

2 Answers

94 Camry idling is low


have your IAC valve (idle air control valve)checked, replace or cleaned. Clean intake with carb/intake cleaner including MAF sensor(V-6 only). Hopefully this helps

Jul 23, 2009 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...