Question about 2008 GMC Acadia

Open Question

Throttle body diagram - 2008 GMC Acadia

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Throttle body diagram


Buy a new-gasket, unbolt throttle-body,
spray carb cleaner inside of throttle body
let soak respray take a long Handel like
tooth brush an clean it once done spray rag
an push threw throttle body several times till
clean an reinstall. Don't get sensors wet at all
an unplugging sensors on some cars can
need car computer reprogramming so
do at your own risk

Jun 01, 2014 | 2005 Chevrolet Blazer

1 Answer

Throttle body float stuck


They are pulling your leg

Only Carburators have Floats

A Throttle Body has Injectors

Could be an issue with the Mass Air Flow Sensor

Wrong reading on air flow you add too much fuel

Dec 13, 2012 | 1985 Chevrolet Monte Carlo

1 Answer

T P S Sencor diagram .where is it, please!


Hi Sharon:
Accordint with this, on 1991 Honda Accord 2.2L FI 4cyl the Throttle Position Sensor is located under hood, center, rear engine area, mounted on throttle valve assembly.

11_23_2011_9_18_17_pm.gif

Fig. 1: The throttle body is attached to the intake manifold inlet. Always use a new gasket anytime the throttle body is removed-1990-93 Accord shown (others are similar)- CLICK HERE FOR IMAGE ZOOM The throttle position sensor is mounted on the side of the throttle body and is connected to the throttle shaft.
  1. Disconnect the negative battery cable.
  2. If necessary, remove the throttle body for access.
  3. The sensor may be removed by unscrewing the retaining bolts.
  4. Reinstall in the reverse order of removal. Make certain the sensor is correctly mated with the throttle body shaft.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 23, 2011 | 1991 Honda Accord

1 Answer

Engine diagram 1997 buick skylark/thermostat


follow the water inlet pipe to water pump the thermostat housing connects to water pump this is for 2.4l engine you have to remove exhaust manifold heat shield.you will see the water inlet pipe going to water pump inlet thermostat housing.for the 3.1 engine follow top radiator hose to thermostat housing you have to remove air filter air duct and filter housing , you have to remove throttle body unit with coolant hoses, you have to disconnect accelerator cable, transmission down shift cables at the bracket bolts to throttle body.once you remove throttle body unit then you can see and remove the thermostat housing to replace thermostat.you need to buy new throttle body gasket,and new small coolant hoses connects to the throttle body unit.have extra gallon antifreeze dexcool on hand.

Nov 15, 2011 | Cars & Trucks

2 Answers

Looking for a pdf. of vaccuum hoses on a 2000 focus


SPI Vacuum Diagram
spivacuumiy9.jpg

Zetec Vacuum Diagram

zetecvacuumtz6.jpg user_offline.gif SPI Vacuum Diagram
spivacuumiy9.jpg

Zetec Vacuum Diagram

zetecvacuumtz6.jpg user_offline.gif spivacuumiy9.jpg

Zetec Vacuum Diagram

zetecvacuumtz6.jpg user_offline.gif If it's equipped with the 2.0L SPI engine (eighth digit of the VIN is 'P'), the most common place for a vacuum leak on these engines, is from the PCV hose that runs from the valve cover to the back of the throttle body. Where it usually rots through is the elbow at the back where it connects to the throttle body. Hope this helps. The only place i could find any views is here. vacuum hose diagram - Focus Fanatics

Oct 29, 2010 | 2000 Ford Focus

1 Answer

Vaccum hose diagram for 88 chevy truck. I put a 350 motor in my 88 chevy 1500 truck from a 95 suburban. I cant get the throttle body to stop idaling to high. I may need a vaccum line diagram for this motor...


it may not be a vacumn leak from a line,check the throttle shaft for movement,for example,i had a 89 1 ton 350 and my throttle shaft was moving around a lot and in order to keep it from idling high,i had to kick the throttle pedal.But also check the idle air control valve,which is the round sensor on the side of the throttle body.

Sep 10, 2009 | 1985 Chevrolet Chevy

1 Answer

Where is the Throttle Positioning Sensor located in a 1997 nissan pathfinder, also is there a diagram that shows all the sensors locations


The throttle positioning sensor is actually mounted to the throttle body on the opposite side of the throttle cable. there are diagrams that show most sensor locations but not 100% of all sensors

Aug 29, 2009 | 1997 Nissan Pathfinder

3 Answers

Diagram of the engine?


if you follow the hose from your air filter to where it meets the engine you will see your throttle cable also connected to this piece on the intake that is your throttle body.

May 22, 2009 | 2005 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...