Question about Cars & Trucks

Open Question

2004 mazda rx8 code p2109

Code p2109 battery goes dead after sitting all night

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 272 Answers

SOURCE: mazda rx8 fault code p0410

The P0410 code refers to the (secondary air system) emissions system. The AIR pump puts air to the exhaust to lower emissions. It takes in outside air and pumps it through two one-way check valves into each bank of the exhaust.
.
About 90% of the time that this code is set, the one-way check valves have worn out or failed and allow water (which occurs naturally in the exhaust) back into the pump. In any cold climate, especially in climates with higher humidity, this water may be more excessive. The water partially fills the AIR pump, it can then freeze. When the PCM commands the pump on, if the pump is frozen it cannot turn, thus overloading the circuit and "popping" the fuse.

A code P0410 may mean that one or more of the following has happened:

  • Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump
  • Blown AIR pump fuse due to freezing up
Possible solution:
This may be covered under the emissions warranty on the vehicle. If your vehicle is out of bumper-to-bumper warranty, check if the emissions warranty is still valid!
  • Replace the AIR pump AND one-way check valve
  • Test and clean the AIR pump AND test and replace the one-way air check valve
  • Replace the AIR pump inlet hose
  • Replace the AIR pump fuse (found under the hood)
It is really only an emissions issue and won't harm your car's engine ot drivetrain. It will however mean you won't pass emission testing if you live somewhere that tests for that like I do!

Posted on Jun 03, 2009

Ad
  • 32 Answers

SOURCE: how to change spark plugs 2004 mazda rx8

Jack the drivers side up and secure on jack stands. Remove the drivers side front wheel. You can then reach through the fender well to remove and reinstall the spark plugs.

Posted on Jun 20, 2009

techbuster
  • 5081 Answers

SOURCE: how do i change both front and rear brake pads on

CHANGING FRONT BRAKE PADS
Jack up the car. Take off your tire. Find the bolt on the back of the caliper and take it off. This should release the caliper, pull the caliper off the disc. Now you should be able to take the pad out. Replace the pad. You'll need a special tool to reset the caliper. As the brakes wear down, the caliper gets tighter so the brakes still work. I'm not sure exactly what its called, but you can borrow one from auto zone. Follow the instructions that come with it to reset the caliper. Slide the caliper back over the disc. If it doesn't go on, you need to reset the caliper more. Put the relese bolt back in. Put your tire back on.Drive slowly and test the brakes.
CHANGING THE REAR BRAKE PADS
The rear brakes on the rx8 are a bit different than most setups...be careful! The only way to move the piston back into the caliper is by way of a special allen head bolt that is directly behind the piston, on the back side of the caliper, installed under a 14mm bolt.
You have to remove this bolt to gain access to the allen head. As you loosen the allen head bolt(counter-clockwise), the piston will move back into the caliper.
Installation is pretty typical, again, the allen head bolt being the unusual part. The manual says to tighten this bolt until the pads contact the rotor, then loosen the bolt 1/3rd of a turn, then reinstall the 14mm bolt.

Posted on Sep 04, 2009

  • 4 Answers

SOURCE: 2004 mazda rx8 power steering

The Mazda RX8 has electric power steering there is no fluid. You may have a problem with you electronic power steering control moduel, or the power steering pump

Posted on Dec 04, 2009

  • 1 Answer

SOURCE: have there been recalls for mazda rx8 2004

Do you mean the oil coolers?There was a recall for the oil cooler pipes which suffer very badly from corrosion

Posted on Nov 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 mazda rx8 immobilizer system


Try first using the ignition key to unlock the system , in case this is locked.

If it is not this, then you can reset the whole system by unplugging battery cables for ten minutes.

Ensure you have your car stereo code if you decide to unplu the battery, as you will be asked for security code when you connect back the battery.

Oct 29, 2008 | 2004 Mazda RX-8

1 Answer

How do i reset ecu on 06 mazda rx8


if you dont have a code reader, the only other way to reset the computer is to disconnect the battery negative terminal and let it sit for a few minutes. If your steering has elec assist there might be a sensor bad did you check the codes in the ecu?

Dec 30, 2011 | Mazda RX-8 Cars & Trucks

2 Answers

My mazda rx8 is heavy to one side


i`m guessing you mean the car is sitting low on one side with no one in it,you will have to check the suspension for damage on the side that is sitting low for something that may be broken or out of position(like a spring not sitting properly).

Sep 01, 2011 | 2004 Mazda RX-8

1 Answer

How to remove the battery from a 2004 mazda RX8


get one of those 9v cig lighter socket power supplies,that will keep codes in yr radio and computer,then you can disconnect the earth first,then positive,then the clamp,then the battery.dont spill the battery acid

Jul 04, 2010 | 2004 Mazda RX-8

2 Answers

MAZDA RX8 2004 Took it out of garage , then put it


Check to see if you are getting fuel to the engine.If not replace the pump relay.Then change the pump if still not working.Check for spark at the wires if you have no spark then change the crank sansor.If still no spark then change the coil pack.

Jul 19, 2009 | 2004 Mazda RX-8

1 Answer

2004 mazda rx8 cranks but won't start


Sounds like you flooded it not with water but with fuel due to moving car with out warming it up all the way before shutting it off. You can take it to the dealer and get a flash update to prevent this in the future. To deflood remove spark plugs and let sit with fan on them over night to dry out. Replace and start cranking for 15 seconds at a time till she starts up. GL!

Mar 21, 2009 | 2004 Mazda RX-8

2 Answers

04 RX8 won't start??


Hold the gas pedal to the floor and try starting the rx8 has anti flood technology that gives less fuel when gas pedal is to the floor I do it all the time hope this helps

Mar 07, 2009 | 2004 Mazda RX-8

1 Answer

Mazda rx8 fault code p0410 secondary air system


Rx8 2004 check engine light it just teas on

Dec 11, 2008 | 2004 Mazda RX-8

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...