Question about Cars & Trucks

Open Question

Remove door panel on 2004 Mitsubishi Endeavor

Need to remove door panel to remove window motor/regular

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chain saw
  • 94 Answers

SOURCE: how to remove front door panel to replace window

FIRST CHECK THE CABLES THAT RUN INTO THE DOOR BECAUSE THEY CAN GET CUT THOUGH COMMON PROBLEM (JUST WERE THE DOOR HINGES INSIDE RUBBER BOOT.) DOOR PANEL REMOVAL...... PRIZE OUT THE TRIM PANEL AT THE BASE OF ARMREST UNDO TWO SCREWS (DRIVERS SIDE) OR ONE SCREW ACCESSIBLE THROUGH THE ARMREST UNDO THE SCREW AT THE BASE OF THE DOOR TRIM IN THE CENTRE. STARTING AT THE FRONT EDGE CAREFULLY PULL THE TRIM PANEL (ABOVE THE INTERIOR RELEASE HANDLE ) AWAY FROM THE DOOR TO RELEASE THE CLIPS, THEN SLIDE IT TO THE FRONT TO UNHOOK THE REAR EDGE OF THE TRIM PANEL.UNDO THE 4 SCREWS IN THE TRIM PANEL RECESS NOW PULL THE DOOR PANELAWAY FROM THE DOOR FRAME RELEASING THE RETAINING CLIPS, SOME FORCE WILL BE NEEDED PREPARE FOR SOME CLIPS TO BE BROKEN THEN LIFT THE DOOR PANEL UP SQUARELY NOW YOU CAN EASILY GAIN ACCESS TO ELECTRIC MOTOR.HOPE I WAS SOME HELP TO YOU THANKS STAN

Posted on Feb 23, 2009

Ad
  • 3 Answers

SOURCE: Cabin Air Filter - 2004 Mitsubishi Endeavor (Where?)

IT IS IN BEHIND THE GLOVE COMPARTMENT YOU HAVE TO TAKE IT OUT BY UNSREWING AND START FROM YOUR RIGHT SIDE

Posted on Jun 10, 2009

  • 119 Answers

SOURCE: want to remove driver side door panel to gain access to power window motor

first remove the tweeter speker if equipped this comes off easily by gently prying from behind, then remove the small panel behind pull handle you"ll find a screw behind it\remove that,the next part is a little tricky the door grip needs to come off to achieve this place a small flat screwdriver at the top of the handle and pry forward the turn handle counterclockwise and this will release it from the clips you"ll then find 2 screws one at the top other at the bottom of door grip remove those and then gently pry from the bottom of the door panel to release the retaining clips thats it

Posted on Jul 14, 2009

  • 1986 Answers

SOURCE: How to remove rear door panel on 2001 continental?

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: need directions to remove driver door interior panel 1997 deville

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The passenger side windows on my 2004 mitsubishi endeavor ls will not work. problem is, the front window is currently down and I can't get it closed.


Check Fuse

Check Switches

Check Motor

Check Regulator


In that order

If you have Retained Accy Relay or
A Window Module,then you need
a repair shop to diagnose

Check means you need electrical
knowledge & a volt meter

May 29, 2011 | 2004 Mitsubishi Endeavor

2 Answers

The plastic inside door handle on my 2004 Mitsubishi Endeavor has broken off. How do I replace??


you need to take off the door panel and there are pins, rods, and cables. so remove the rod and pin for the door handle and it should pop out.

Dec 07, 2010 | Mitsubishi Endeavor Cars & Trucks

1 Answer

Is there a step by step instruction on how to change the left side mirror on my Mitsubishi Endeavor 04 ? thank you


Maybe try alldata.com, because on my online resource for the 2004 Mitsubishi Endeavor, there is no information on body work.

One could get the part from the salvage yard and look for the bolts like one would do for a GM car

One may have to remove some plastic parts to get at the fasteners.

Also, if there are cables for moving the mirror from the inside, then that should be considered, as well.

Also, if the mirror is heated, that should be considered.
---
(I got this off of Wiki Answers)
Very easily. Open the door, find two rubber circular boots right behind the
mirror. Take them off to expose the 2 bolts that hold the mirror on. Take the
bolts out and unplug the wire. Reverse these steps to install, hole this
helps...

There are three small bolts holding the driver's side mirror on. Two can be
accessed by opening door and removing the two circular rubber boots seen on the
upper end of the door . To access the third bolt you will need to remove the
door panel. you will need a forked driver to help remove the door panel. It can
be bought at any auto parts store. It has a flat Y shaped head that can be
inserted along the lateral and bottom edge of the door panel to pop it way from
the door frame. There are three screws holding the door panel on. Two under the
door handle and one behind the door latch. Then the door lifts up and off. Make
sure you have the window down before you take the panel off because you cannot
access the third bolt unless it is. You will have to unplug the electrical
connects that power the controls on the door handle to completely remove the
door panel. After you remove the panel there will be a hole in the upper right
hand door frame, possibly covered by a black patch. Beneath this is the third
bolt. you will also need to disconnect the light from inside the door frame
before you will be able pull the mirror off. There is a large rubber boot oval
shaped that you can pull out and you will see the electrical connection for the
mirror inside the hole on the right.


Good luck on this repair.

Oct 07, 2010 | 2004 Mitsubishi Endeavor

1 Answer

How to replace power window motor


You'll need to remove the door panel and as the motor is riveted in you'll need a drill ... The window in the opposition with the use of duct tape tape it up so that it will not fall on you. Disconnect the power source to the motor itself and drill out the three rivets that hold it in place. Be sure to observe the way it is installed before removal as well as the guides that may be connected to it remove the old motor install the new one re-rivet the new one into place reinstall it the way the old one came out re-connect the power source and test the window by installing switch to ensure that it is working properly.

Nov 07, 2009 | 2004 Mitsubishi Endeavor

1 Answer

How do i remove the left rear panel on 2005 Endeavor?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Oct 26, 2009 | 2005 Mitsubishi Endeavor

1 Answer

Need to remove rear door panels on a 2005 endeavor - windows have come off tracks and do not close


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Oct 19, 2009 | 2005 Mitsubishi Endeavor

1 Answer

Describe your my Mitsubishi endeavor 2004 back door doesn't open Problem


Does this not open from inside or outside or both.
If it opens from the inside and not the outside look at the door opening near the latch. Look for the small lever "child-lock" just move the lever in the oposite direction.
If the door doesn't open from inside or outside I would ask has anyone try to unlock the car using a "slim-jim" if so they may have caused the lock rod to come off the latch on the inside. You'll need to remove the door trim panel and see the the rod has come off. With any luck it will just pop back on if the nothing is broken.

Jul 08, 2009 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...