Question about Cars & Trucks

Open Question

1986 Dodge Ramcharger 4x4 front axle wont engage

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: front axle - front drive shaft Toyota tacoma 1998 4x4

more than like have a broken axle shaft, un hook the rear drive shaft and put it in 4wd if it wont move then you know you got a broken axle shaft or spider gears broke in the pumpkin

Posted on Dec 09, 2008

  • 124 Answers

SOURCE: 4x4 not working when i shift it in 4x4 auto trans

Find the accuator on the front axle it has a two wire pigtail and threads into the axle housing. Check for power and ground if you have both when the transfer case is in 4x4 the replace the accuator. They are available at most parts stores and are a very common problem. Let me know how it goes.

Posted on Dec 16, 2008

  • 1 Answer

SOURCE: 2001 Trooper: Front axle will not engage when I press dash 4x4 switch

hi guys i would check all the small vacume pipes that conect the sol valves toi the vacume actuators having just replaced the engen in mine i found that these do not have any clips holiding them on tight and can get oil on them and become oversized and leak you can test the diaframes in the actuators by putting a length of pipe on one port and sucking by mouth you can hear the actuator move and then find you can put toung on end of pipe and it will hold a vacume if it does not then chances are the actuator diafram id u/s hope this helps bill

Posted on Jan 09, 2009

  • 180 Answers

SOURCE: 1986 K5 Blazer front hub/axle problem

3 bolts from the back, axle nut and take the caliper off pretty easy.

Posted on Jan 21, 2009

  • 1 Answer

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Posted on Feb 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the vacuum shift motor located?


Gordon, I will take a guess, the Vacuum shift actuator/motor is located on the front axle. Check the attached pictures of actuator and how to replace video,links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Diagnosing 4WD Engagement Problems on Dodge Ram pickups
Front Drive Axle 4wd Vacuum Disconnect Motor 1AFWA00007
Front Axle 4 Wheel Drive Actuator Replacement 4x4 Dodge Ram

May 18, 2016 | 1983 Dodge Ramcharger

1 Answer

I have a 1986 ramcharger royal se w150 4wd. What type of front axle does it have? dana 44,dana 60, automatic or full time locking hubs?


should be dana 44's.... the is a front axle disconnect on the tube operated by vacuum ...when shifted to 4wd, the slide engages the 2 axles to make one

Sep 17, 2010 | 1986 Dodge Ramcharger

2 Answers

4 wheel wont work have 3 vac line gone on pas side where do they go 85 dodge ramcharger auto


The lines connect to the toggle switch, and run down to the transfer case.

Feb 03, 2010 | 1985 Dodge Ramcharger

2 Answers

1995 dodge 1500 4x4 v-8 4x4 will not engage in


hope you can help. I have a 97 Dodge 1500 4x4 with a 5.2 litre and auto trans. After shifting to 4x4 high when you move there is a clicking sound form left front axel

Dec 28, 2009 | 2000 Dodge Ram 1500 Truck

1 Answer

Dodge 1986 W 150, transfer case shifts, but 4WD wont engage, Where should I start?


the vaccum lines on the front axle check them they are what really engage the 4 wheel check the whole hose

Dec 22, 2009 | Dodge Pickup Cars & Trucks

1 Answer

In my 1986 Dodge Ramcharger the transmission No reverse


Pull the bottom pan and check the Rear (Reverse) Band.

May 11, 2009 | 1986 Dodge Ramcharger

1 Answer

Front axle - front drive shaft Toyota tacoma 1998 4x4


more than like have a broken axle shaft, un hook the rear drive shaft and put it in 4wd if it wont move then you know you got a broken axle shaft or spider gears broke in the pumpkin

Dec 09, 2008 | 2007 Toyota Tacoma

3 Answers

Dodge 4x4 Doesn't Engage


1998 dodge ram quad..front end wont lock in or the lights come on to tell you its in 4x4..***** little

Oct 03, 2008 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...