Question about 2004 Suzuki Aerio

1 Answer

Crankshaft position sensor

ENGINE LIGHT ON.RESET AND AGAIN COME BACK.P0335 CODE CRANKSHAFT POSITION SENSOR BAD

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Suzuki Master
  • 21,873 Answers

The sensor would need to be tested with a meter. If it is faulty, the engine and - or transmission has to be removed to replace it.
You should be able to find the wiring harness as it goes into the transmission housing near the block.

Posted on Apr 24, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

Code p0335 crankshaft 2008 BMW why code 2a94 & long cracking?


Ok! Both codes have to do with the Crankshaft position sensor. The P0335 means that you should replace the sensor, the 2a94 tells the pcm what code to display for the problem. Here is somthing you can do to make sure the sensor is really bad: If you unplug (or lose power to) your PROcede while the car is running. Or tried starting it while it wasn't plugged in fully, you will throw that code. Just clear it and see if it comes back. If it reoccurs while the car is driving, then you might have a bad Crankshaft position sensor.

Jun 26, 2014 | 2008 BMW 328i Sportswagon

1 Answer

Po335, engine ligt on, slip and vdc brake light on 2005 armada


Error Code: P0335
Description:
Crankshaft Position (CKP) Sensor - Circuit Malfunction
Possible Cause:
Wiring.
Crankshaft position (CKP) sensor.
Engine control module (ECM).

Mar 25, 2014 | 2005 Nissan Armada

1 Answer

P0335 code car shuts off when driving?


P0335 stands for Crankshaft Position Sensor Malfunction change the sensor and the car should run great but in order to remove the check engine light you have to hook it up to a scann tool and press erase codes

Nov 20, 2012 | 2006 Hummer H3

1 Answer

Engine management light on trouble code P0335


P0335 - Crankshaft Position Sensor 'A' Circuit Malfunction

Possible causes- Faulty crankshaft position sensor (most common)
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery causing slow engine crank over.

Oct 25, 2012 | 2005 Fiat Punto

1 Answer

Trouble code p0335


Replace the crankshaft position sensor and you should be up and running like normal. Verify that there is no power or ground problem to the crankshaft sensor, the Yellow/Black wire should have battery voltage any time the key is on and the main relay is energized.Verify that the Brown/Yellow wire has a good ground. If all is good then replace.


P0335 - Crankshaft Position Sensor A Circuit Malfunction
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

Symptoms:
NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include:
Vehicle may not start (see above)
Vehicle may run rough or misfire
MIL illumination


A P0335 "check engine light" code could be caused by:
Damaged CKP sensor connector
Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
Sensor output open
Sensor output shorted to ground
Sensor output shorted to voltage
Failed crank sensor
Broken timing belt
Failed PCM

Possible Solutions:
Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal.
If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs?
If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay?
If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

This code is basically identical to P0385. This code P0335 refers to Crankshaft Posistion Sensor "A", whereas P0385 refers to Crankshaft Position Sensor "B". Other crank sensor codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.


Hope helps.

Dec 18, 2011 | 2006 Jeep Liberty

1 Answer

Replaced camshaft and crankshaft position sensors in my 2005 altima also the o2 seneor car still will not run. error code 335 What else could be the problem?


DTC P0335 - Crankshaft Position Sensor A Circuit Malfunction
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

A P0335 "check engine light" code could be caused by:
Damaged CKP sensor connector
Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
Sensor output open
Sensor output shorted to ground
Sensor output shorted to voltage
Failed crank sensor
Broken timing belt
Failed PCM

If you need additional details about test and solutions, just contact us in the Code Link.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using Fixya, and have a nice day.

Jose.

Oct 21, 2011 | 2005 Nissan Altima

2 Answers

Crankshaft Position Sensor Error P0335 recurred after r&r


In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Jul 25, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
2004 Suzuki Aerio Logo

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...