Cars & Trucks Logo

Related Topics:

Anonymous Posted on Apr 23, 2013

Central locking not working

My central locking has stopped working from the keys. it also says no fuse where the mileage should be and it keeps going back to german when you change it to english

1 Answer

_-__-___-_

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Jeep Master 20,706 Answers
  • Posted on Jan 13, 2015
_-__-___-_
Jeep Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Apr 06, 2013
Answers
20706
Questions
2
Helped
6803808
Points
57965

It didn't lie , the fuse is blown
find it?
if you scan it, that , no fuse ,expands to who blew.

can i assume you read the operators of unstated year car?
and see all fuse boxes.????
you could just look, and see the blow fuse.
or use any voltmeter (key on) measure both sides of all fuses
easy, 0v is blow fuse. need a video, we have like 100 s doing this.

ever seen a scan tool, plug it in,
you buy and plug
you rent and plug
or any shop in town will, ask them.

some fuse look good and are not.
that is why pros, use a voltmeter, it NEVER LIES

5 Related Answers

ginko

Ginko

  • 19396 Answers
  • Posted on Sep 13, 2008

SOURCE: porsche key fob

If the key had gone faulty, the key code must be re programmed on the vehicle computer. This can be done only using a PIWIS tool, available at the dealer or at a qualified Porche garage.
Try also the following reset:
turn ignition on,
turn off.
remove the transponder from the column
push any button on the fob within 6 seconds.
This procedure will reset the key synchronizing again with the vehicle computer.

Ad

Anonymous

  • 63 Answers
  • Posted on May 03, 2009

SOURCE: Z4 Central Locking problem - drivers door.

looks like you will need a drivers door lock actuator (contains the latch)if the door will not unlock with the remote either.the lock cylinder usually will fail since you had to use it everytime to unlock the door. the lock cylinder is vin specific so expect a delay when its ordered from the dealership.i would probably expect around $800 for the complete repair, kinda pricey but the dealership will go out of its way to retain a customer.

Robert Debison

  • 412 Answers
  • Posted on Jun 12, 2009

SOURCE: 2005 Chrysler Grand Voyager. Central locking

the body control module may need a software update..check with your local dealer

rgbypoet

  • 166 Answers
  • Posted on Jan 13, 2010

SOURCE: key thob has stopped working, I have changed the

Saab's have very specific steps that you must follow when you change the batteries in your key fob. You might try these steps to re-sync your key fob to your security system....

If the battery has been changed outside the
car and the car is locked, proceed as follows:
1 Unlock the front left door with the traditional
key. If the car has a car alarm, this
will be tripped.
2 Open the door and insert the remote
control into the ignition switch. If the car
has a car alarm, this will be silenced.
The remote control and receiver unit are
now synchronized.

Anonymous

  • 4793 Answers
  • Posted on May 06, 2010

SOURCE: mk3 golf when central locking is activted the electric windows go

you have just found this out.it is a standard feature of all vw/audi/seat/skoda cars
unlock/hold key over,the windows will go down
lock/hold key over the windows will go up
then unlock the car with the remote,car reset.
sit in car with engine on,switch off engine(do not open any door)driver can open/close any window(you can even put your hand into window frame and it will rollback,all on its(not for fun)
if windows rollback after you have used button to close them you may have sticky runners/rubbers.
this is not in the hand book,tell all your friends.....only a german car.....

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2007 Ford Transit Connect Van. The central locking has stopped working on the fob. I have changed the fob battery and still not working. Does it have a fuse/relay that could be broken?

There is only one fuse that mentions 'Locking', but also refers to the General Electrical Module (GEM). If you change the fob battery, you need to reprogram it to the vehicle. Or you could open any Transit around you. Lots of help below including resetting..

Ford Transit Connect Central Locking Issues

JustAnswer https://www.justanswer.com > UK Ford Repair
Jul 6, 2010 - Hi, My transit connect central locking isnt working both with key and fob, and my side loading door is permanently locked, how do i get the ...

1 answer · Top answer: Look above accelerator pedal, there should be 2 fuses taped to the loom, check they haven't ...

Why is the ford transit 2007 central locking not working?

Vehicle History https://www.vehiclehistory.com > questions > why-is-t...
Apr 9, 2020 - When the central locking system is not working in Your 2007 Ford Transit the first thing that You should check is the fuse to the locking system ...

2007 Connect Key Fob Problems

FordTransit.org https://fordtransit.org > forum > viewtopic
Jul 2, 2013 - 1. Close all the doors. · 2. Turn Ignition key from position 0 to II eight times within 10 seconds. · 3. Locks will cycle (locks then unlocks the ...

Ford Transit Forum • View topic - Key Fob not working
Aug 11, 2017
How to reset my central locking fob - Ford Transit Forum
Jul 21, 2009
Mk7 remote key fob programming/pairing - Ford Transit Forum
Mar 12, 2015
View topic - MK 7 central locking problems - Ford Transit Forum
Mar 31, 2007
More results from fordtransit.org
163 20 amp GEM VBATT locking

Ford Transit Connect mk1 (from 2002 - fuse box diagram

Auto Genius https://www.autogenius.info > ford-transit-connect-mk...
Sep 23, 2015 - Engine compartment fuse box ; 23, 20, ABS valves ; 24, 10, Glow plug monitoring (diesel engines) ; 25, 10, Main beam right-hand side ; 26, 10, Air ...


0helpful
1answer

S reg vauxhall corsa 1998 central locking has stopped working

https://manuals.co/workshop/opel/corsa/opel-corsa-1997-2000-workshop-manual-haynes/5530701/3

You might have just blown the fuse, otherwise it could be the control module wiring has been damaged.
Check tthe wiring in the manual above.
0helpful
1answer

Wipers stopped working & central locking system stopped working on my 2003 range rover

The alarm and the central locking are all part of the remote keying system. You will not fix it with changing fuses because it is likely the ECU needs to be be reset. Unfortunately, it will require a visit to an authorised workshop to do this
1helpful
1answer

Hyundai Accent 1.4L GLS 2000 Central Locking not working

FOR Central locking not working on 2000 Hyundai accent?Click the link below :-----

http://schematicsdiagram.blogspot.in/2012/03/this-is-how-system-operates.html

This will help.

Thanks.

5helpful
3answers

Toyota corolla verso 2007 . the central locking has stopped working

Toyota Corolla Verso - Central locking has just stopped responding


So you don't waste your time, here are some assumptions: -

1. When I press the key fob there is no sound of doors trying to lock/unlock and I know the key fob is fine.


Solution:


In this situation reset the alarm/locking system

Below is the procedure I followed to get the central locking working again: -

Open the passenger door, and look at the side of the dash board. There should be a triangular panel. Pull the panel off to reveal a small set of fuses(see the back of the panel for the fuse map). To power down the central locking you need to remove the Dome Light fuse, this is located top left. Second one down 7.5 amps. (if in doubt remove the top two 7.5 amp fuses I did)

When you remove the fuse(s) you will notice the interior light go out indicating you have powered down the system.

Now leave them out for at least 30 mins so any capacitors can discharge properly. (Be aware while the fuse is removed all central locking is disabled, so the other doors are open. I left the fuse(s) out over night with all the doors open but I don't recommend it, 30 mins should be fine)

After 30 mins replace the fuse(s) close all doors, and then try your key fob, hopefully you should here that satisfying locking sound.


2. When I press the key fob I hear the locking system trying to engage.

This could be a faulty door switch on any door including the boot, or there could be a dent in the inner door panel of any of the doors, usualy the rear doors due to the seat belt not retracting properly.

Solution:

Check all door switches for damage, and check inner panel for dents, just a small dent where the switch connects can be enough to not engage the switch. This will stop the central locking.

Use some kitchen roll wrapped in tape (as a makeshift pad) and tape to the inner door as a temp measure to engage the door switch. At least you can then lock the car.


5helpful
1answer

Central door lock system not working

CHECK THE DOOR LOCKS MAIN FUSE.
4helpful
2answers

Ford focus central locking

Hi steve,try the central locking fuse,fuse 63.its in a stupid place (thanks ford)its at the back of fuse panel.two bolts release the fuse board,turn it around and there it sits,20 amp fuse.replaced mine and its working great.hope this helps mate
0helpful
1answer

Cental locking not working and radio/cd not working

is central locking not working with remote & did you try using key to see if central locking is working at all if working with then its a good chance that key fob is faulty if its not then first need to check fuses & for radio is it going on when switched on display will say code---- if it does then it req code if not then again possibilty a fuse might be on same circuit as your central locking fuse
0helpful
2answers

Central locking not working

if your talking about locking with the remotes.try reprogramming them.cycle the ignition key from run to off 8 time within 10 seconds ending in the run position.the horn should honk.now you are in programing mode.hit the lock button on the first remote then hit the lock button on the second remote.and tunr the key off
Not finding what you are looking for?

148 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...