Question about 2007 Chevrolet Uplander LT Minivan

1 Answer

I need to know how to install the passenger side turn signal

The turn signal assembly is for a 2007 Chevy Uplander Lt. It is located below the headlamp assembly in the bumber cover. I found the part online for about 15 dollars when the repair shop told me 75 dollars. I just dont know how to do it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Tools needed: pair of regular pliers
Look around for black, plastic wingnuts on the back of the assembly - you'll probably need a pair of pliers for leverage to loosen them up. If the assembly is nested with the headlamp assembly, just loosen the whole thing and pull it out. Just note how the things come off so you'll put them back in the same order and position. There may be an odd-shaped kind of circular metal retainer that holds the lamp socket onto the back of the turn signal fliffersham - that should twist off without any problem. Replace whatever it is you're replacing and hook the lamp back up, being careful not to touch the bulb - they don't like greasy fingerprints (although the halogen-type bulbs are even more persnickety). Make sure the lamp socket retainer is screwed on correctly and tightly (It's a terrible design and is difficult to tell if it's really seated properly) and then fasten the assembly back onto your bumper with the wingnuts - tighten gently with the pliers.

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of water pump on 2007 chevy uplander


Passenger side, front of engine. Near the center. It has a big black pulley mounted to it. Smooth sides.

Jul 19, 2015 | Cars & Trucks

1 Answer

Where is the motor blower resistor located at on a 2007 chevy uplander


Hi,
The website attached states that it is located under the passenger side of the dashboard. It is into the bottom of the heater case.

This website also looks very useful for any other chevy related questions you may have as they have mechanics there to help you.

i hope this helps.

found this helpful answer from chevy mechanic on JustAnswer com

Jun 20, 2015 | Cars & Trucks

1 Answer

3.8l 2007 chervolet uplander lt change thermostat still no heat


Most likely cause is a faulty actuator. It will need to be scanned to be certain.

Dec 28, 2012 | 2007 Chevrolet Chevrolet Uplander

1 Answer

How do i change the headlight bulb on my 05 uplander


On my 2003 trailblazer (as far as I know they are the same), See note below for passenger side. Remove the dust cover on the back of the head light assembly (black round rubber cover about 3" in diameter, just pull it off), disconnect the plug on the bulb, turn the bulb a 1/8 turn and pull it out. Then reverse the process for assembly. ***NOTE***If you are trying to replace one of the bulbs on the passenger side, remove the air filter housing cover and displace the filter for access to the dust covers on the back of the head light. 2 screws hold the air filter housing cover on, one directly behind it and one on the side (drivers side of air filter housing).

Aug 23, 2010 | 2005 Chevrolet Uplander

1 Answer

How can I change the front signal lamp on the Chevy uplands 2007?


The headlamp assembly must be removed. There is a pin and small bolt that need to be removed then the head lamp can be pulled out. This will give you access to reach down and twist the signal lamp socket loose.

Jul 25, 2010 | 2007 Chevrolet Uplander

1 Answer

I want to replace the left rear turn signal bulb on a 2006 Chevy Uplander


Open your lift gate and you will notice the lamps are incased in a black plastic housing. There are 3 star screws you need to remove in order to pull out the housing and change the bulb. You may need to buy a a special screwdriver or bit for one.

Dec 08, 2009 | 2007 Chevrolet Uplander LT Minivan

1 Answer

Change the light buld in my 2007 chevy uplander tail turn signal with the size in book however it stays let does not blink


Does only one side do it or both. If signals on both sides fail to flash but stay on steady, then it is probably the flasher unit. If you don't hear a clicking sound inside the vehicle its probably got welded contacts. It should be near the fuse panel, just unplug and plug the new one in.

Sep 04, 2009 | 2007 Chevrolet Uplander LS Minivan

Not finding what you are looking for?
2007 Chevrolet Uplander LT Minivan Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...