Question about Cars & Trucks

1 Answer

I have a 2004 Chevy blazer. And I replaced the crankshaft positioning sensor 5 times! What's the reason?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 40,666 Answers

Check the adjustment and position of the sensor in relation to the clearance to the crankshaft as if it is too close it touches the exciter on the crank and if too far away it will only read occasionally.

Posted on Apr 23, 2013

  • thegothicfai
    thegothicfai Apr 23, 2013

    Well the mechanic put shimmies on it?

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 84 Answers

SOURCE: crankshaft position sensor replaced and car shuts off

Hello, The crankshaft sensor is located at the left rear of the motor, behind the left cylinder head where the transmission bolts up. I believe that it has a 6mm allen head screw holding it down.
I hope this helps.
CYA, Gator241

Posted on Feb 06, 2009

  • 1 Answer

SOURCE: 2004 Nissan altima 2.5 liter Crankshaft Position Sensor

Yes, the sensor can be replaced in your garage (if you have some decent auto repair experience).
This is not an easy job due to the location of the crank sensor.

Below are the steps I used to replace the crankshaft position sensor.
The steps are for a 2004 Nissan Altima with a 2.5 liter engine.

Nissan has a crank and cam sensor kit. I would not buy any aftermarket sensors because of the effort required to replace the sensors. (I do not work for Nissan). The information below is compiled of tips I found on the internet and my own experience. Even though these procedures may appear lengthy, it took me much longer to figure out the correct steps involved for this task.
Even though I have included all of the steps (and hints) I used… THIS IS NOT AN EASY JOB FOR THE “DO IT YOURSELFER”

CRANK SENSOR IS LOCATED AT FIRE WALL SIDE OF BLOCK BETWEEN MOTOR MOUNT AND FLYWHEEL. YOU GET TO IT FROM TOP.
Remove the (4) allen head bolts that hold the plastic engine cover. Remove the air tube that connects the throttle chamber to air filter box. Pull off the valve cover breather hose with the air tube. Now place a drop light under the two rubber heater hoses (at the firewall on the drivers hand side), shining the light forward towards the back side of the block (below the intake runners). To see the crankshaft sensor and connector, look between the valve cover and the throttle chambers (intake runners) on the drivers side, look straight down toward the ground… look for the sensor with a black wire connector with a green tab on the side, held to the engine block with a gold colored 10mm hex headed bolt. You will need to view the sensor from this position as you are following the steps below to remove and install the crank sensor. There is a large wiring harness bracket attached to the transmission bell housing that was temporarily unbolted to aid with the removal and installation of the crank sensor.

What turned out to be the biggest problem was the connector securing the wiring harness to the sensor. Unlike the camshaft position sensor connector that is removed by squeezing in on a tab located at the top of the connector, the crank position sensor was secured to the harness via some green colored push button assembly. To remove the crank sensor connector, the green tab must depressed ALL THE WAY DOWN (towards the block) UNTIL THE GREEN TAB LOCKS INTO PLACE - REMAINING IN A “PUSHED IN” POSITION (You should hear a “click”). I was able to accomplish this by viewing the connector as described above and at the same time, reach around the back side of the engine using a 6” – 8” flat blade screw driver (with a large head) and push the green tab in towards the block until it locked into place. After the green tab was depressed and locked, (still viewing from above) I repositioned my hand holding a smaller flat blade screw driver to gently pry the connector off the sensor inserting the blade of the screw driver between the bottom of the connector and the crank sensor (a slight twist should do it). I do not recommend pulling on the connector wires or trying to pull the connector off with pliers as damage may result - because in my world of auto repair, if there is a chance that something will break because I am not careful… IT WILL BREAK! After you have removed the connector and while viewing from above, use a ¼” drive ratchet with a 6” extension and a 10mm socket to loosen the gold bolt holding the crank sensor in place. I recommend that you loosen the bolt with the socket, then reach your hand around to the connector and remove the bolt by hand. After the bolt is removed, use an 8” slip jaw pliers - set at its widest opening setting – to grab the sensor. First twist then pull out the sensor.

Be sure to clean the inside of the sensor’s wiring connector with break cleaner spray and blow out with compressed air to get rid of any oil that may have leaked into the connector from the defective crank sensor… this is what probably caused the trouble code in the first place.

You are now ready to install the new crank sensor. If you purchased the crank and cam sensor kit from Nissan, make sure that sensor with white dot at bolt whole goes to the crank. Be sure to oil the rubber “O” ring. I was not able to get the green tab on the connector to snap back into place while the new sensor was installed in the block. I installed the connector to the sensor while it was out of the block – the green tab still did not pop back into its original position on its own – so…while the connector was installed as far down as I could push it, it used a small flat blade screw driver to push on the bottom of the green tab towards the top. That did the trick. While viewing from above, I placed the crank sensor back into the block. I was not able to get the rubber “O” ring to seat within the block by hand. I used the gold bolt to draw the sensor in while slowly tightening. HINT: I taped the outside of the washer of the crank sensor bolt to the 10mm socket to hold the bolt on place while I inserted the bolt into the block… you can do this by hand, but I didn’t want to drop the bolt . I also taped the socket to the ratchet extension so the socket would not get stuck on the bolt (it’s a snug fit down there).
If you were able to accomplish the above procedures, the cam sensor is a snap to remove in install. It is located in the driver’s side portion of the head facing the wheel.
Remember to reinstall all brackets and items that were removed.
Good luck!

Posted on Feb 17, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 1071 Answers

SOURCE: How do I replace the timing belt and the crankshaft sensor ?

if you have never done one take it to a shop because if you have the timing off a little you take a chance of bending valves then you would need a new head

Posted on Jul 23, 2009

ZJLimited
  • 17970 Answers

SOURCE: crankshaft position sensor location

1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.

87c675c.jpg

Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship

Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.

I really hope help you wuth this (rated this help). have a nice day, good luck.

Posted on Sep 25, 2009

Testimonial: "Awesome. Thanks."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor on my 2010 srx 3 liters


Camshaft/Crankshaft Position Sensor Replacement - Cadillac Forums

www.cadillacforums.com/.../261074-camshaft-crankshaft-position-senso...

May 29, 2012 - 8 posts - ‎4 authors
I have a 2004 CTS - 3.6L and am trying to get the camshaft position ... at my local Auto Zone and it simply shows camshaft position sensor A. Code P0340 Camshaft Position Sensor
14 posts
Mar 23, 2013
How to change the camshaft and crankshaft position ...
6 posts
Oct 9, 2011
Where is camshaft position sensor on 2003?
7 posts
Dec 28, 2009
Crankshaft Position Sensor 3.6L 04 CTS
5 posts
Jul 15, 2008
More results from www.cadillacforums.com

2004 Cadillac DTS crankshaft position sensors - YouTube

? 3:22
https://www.youtube.com/watch?v=jbjLJZzF3xA
Sep 16, 2013 - Uploaded by Rogelio Cervantes
Quick overview crankshaft position sensor replacement for a 2004 Cadillac DTS 4.6 liter North Star. ... 2003 Cadillac CTSCrank Position Sensor Part 3 Done!!! - Duration: 8:21. 2LateIWon 8,433 views. 8:21. How To Check .

Jan 16, 2016 | Cars & Trucks

2 Answers

98 blazer 4.3 engine won't start code p0336, already replaced crank sensor


which crank sensor do you replaced ? the P0336 means P0336 Crankshaft Position Sensor A Circuit Range/Performance.

________________
autel maxidas 708

Feb 25, 2013 | 1998 Chevrolet Blazer

1 Answer

Have enjine codes on 1996 chevy blazer 4.3 that read po339/po341 what is the recommentded fix


both codes refer to Crankshaft position sensor A code 339 is CKT Intermittent and 341 is CKT Range Performance. you may have to replace the sensor.

Jan 27, 2013 | 1996 Chevrolet Blazer

1 Answer

Error Code P0315 on 2007 Chevy Aveo


P0315 - Crankshaft Position System Variation Not Learned

Possible causes- Crankshaft Position (CKP) sensor harness is open or shorted
- Crankshaft Position (CKP) sensor circuit poor electrical connection
- Faulty Crankshaft Position (CKP)
- Damaged crankshaft pulse wheel teeth. Tech notes Visual inspection of the Crankshaft Position (CKP) sensor and crankshaft pulse wheel teeth for damage. If crankshaft teethes are OK, replaced the Crankshaft Position sensor

Sep 11, 2012 | Chevrolet Cars & Trucks

1 Answer

2002 chevy blazer no spark or injector pulse


Replace the crankshaft position sensor. If the PCM doesn't see the crank sensor it will not allow spark OR injector pulse.

Aug 20, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

I need a diagram for crankcase position sensor on a 2004 Chevrolet Trail Blazer


Attached is a drawing of 6 cyl 4.2L engine, crankshaft position sensor is item #709 on driver's side of engine toward rear.

freddyboy61_4.gif

Aug 08, 2011 | 2004 Chevrolet TrailBlazer

2 Answers

Chevy blazer wont start 2002


if it turns over there are a cocuple of things to check. crankshaft sensor and the coil pack maybe the computer.id start with the crankshaft sensor

Jun 29, 2008 | 2002 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...