Question about Cars & Trucks

Open Question

Xj40 Jaguar, how do I replace the exterior rear door handle

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 43 Answers

SOURCE: Need to know how to install exterior door handles

I'm assuming that you have the coupe not convertible since I've had same problem with my 97 Dodge Avenger and this is quite common from what I have heard. The handle is held in place by two 10mm bolts. One is easily accessable, located right beside the handle with the door open. The other is a little harder to get at. The first thing you need to do is remove the inside door cover, held in place by four screws and push in clips along the bottom that pull out easily. Two of the screws are visible and in the top corners of the door panel. One screw is located behind the inside handle and once removed the moulding comes off quite easily. The other screw is in the hand hold where you pull the door closed and has a small plastic cover over it. If you have power windows you are able to disconnect the switches once the panel is off. If manual windows, the handles are usually held on by a clip that can be pushed off with a screw driver allowing you to pull of the crank handle. The window needs to be in the closed position so you can access the ONE 10mm bolt holding the outer door handle. Once the interior door panel is off, if any clips remain in the door, take them out and put them where they should be in the door cover it won't go back together properly if you don't. Now you'll need to pull down the corner of the plastic covering the door, don't remove all the plastic just enough to allow access to the bolt. I used a small rachet to get it out. It is in a stupid spot with not much room but is doable. Once out, the handle is only being held by the lock rods to the handle and lock cylinder. The lock cylinder is held by a retaining clip which can be slid off allowing the cylinder to be pushed out. The other rod connected to the handle has a plastic clip on it holding it in place. This can be opened with a small screwdriver. Once opened the rod will come out easily and the handle should come off the door. The only problem reinstalling, that I had, was reconnecting the rod to the handle and found that if you unscrew the door latch, the whole mechanism can be moved down, giving you more freedom to work with the rod. You might want to do this before fighting with the clip holding the rod in place, just a thought as I got mine apart in 20 min. Installing the new handle is quite easy, just attach rod to the handle FIRST before anything else. Once the handle is back on the door the lock cylinder can be pushed back in, it just gets in the way if you put it in the handle right away. Hope this is of some help.

Posted on Oct 05, 2008

  • 508 Answers

SOURCE: How to replace '96 Ford Explorer driver side exterior door handle

You will need to remove the door panel to gain access to the handle. Roll the window up or down as needed to get to the nuts that attach the handle to the door. You will also need to remove a rod the goes to the door lock. You will see the rod after the door panel is removed. Good luck.

Posted on Feb 18, 2009

wireguy212
  • 1627 Answers

SOURCE: replacement exterior door handle

you will need to get the door panel off the inside,undo the linkages and the remove the nuts holding the handle on.

Posted on Jul 28, 2009

  • 104 Answers

SOURCE: how to install replacement door handles for 98 ford ranger pickup

remove interior door panel(need special tool to pop plastic clips holding panel to door)with panel off remove plastic film,with window up you should be able to see two 10m nuts-bolts to remove-also have to pop lever off that goes down to door latch

Posted on Sep 19, 2009

  • 1986 Answers

SOURCE: replace exterior door handle on a jeep commander

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door

Posted on Oct 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is a fuse box for windows in Jaguar JV6 1983


either side in front of vehicle botton of front door pillar ,has a cover over it with a slot in the head of the fixing ,cannot remember which fuse though ,but it should be a 25 amp one ,their is also fuses in the centre console ,well their is on mine but mines a 94 XJ40 ,Handy place is the jaguar XJ40 /300 models on facebook ,iam on that as well .

Jun 22, 2017 | Jaguar Cars & Trucks

1 Answer

Warn light box on theright side of dash don't show any simbols ie door open, seat belt not fitted etc but flashs amber.


the common prob with old xj40 with odd readings on insrument pack is bad connection inside the pack itself with good eyesight carefull dismantling and a soldering iron it can be fixed

May 13, 2017 | Jaguar Cars & Trucks

1 Answer

Replacing Exterior Door Handle on 1989 burb


if you can not get to the handle at all you will need to go from the inside. if that is the case try and pry the top of the door panel off without distorting the panel. then with a flash light look down inside the door and you should see a metal rod, try pulling the rod up or down which should open the door! hope this helps

Feb 22, 2014 | GMC Cars & Trucks

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

Are there new exterior door handles for 1994 xj12 jaguars


I recall seeing exterior door handles on Ebay the other night. I think that they were used, but I think that getting new ones are going to be expensive, and hard to find. I hope that this helps.

Jan 10, 2010 | 1994 Jaguar XJ12

1 Answer

How do i open the fuel filler lid on trunk for XJ40 1989


Its in the trunk under the fuel filler. a small plastic handle. pull it towards you.

Jun 30, 2009 | 1994 Jaguar XJ6

2 Answers

Need instructios to repair 1997 Toyota Camry Broken Exterior Door Handle


Two 10mm bolts, or nuts, hold the handle on from inside the door. dont forget to remove actuating rod from old handle. probably clip is broke also.

May 30, 2009 | 1997 Toyota Camry

1 Answer

93 exterior rear door handle replacement


You probably won't get it off from outside. The two bolts go from inside out I believe.

May 15, 2009 | 1993 Honda Civic 4 Door

2 Answers

1990 Jaguar XJ40 3.6, where is the fuel filter located?


Hi,
The fuel filter is located under the car, in front and in a little, from the L/H rear wheel.

Undo the 2 nut connections, and fixing clamp, and its off.

Remember no smoking !

Good luck !

A FixYa rating would be nice... Thanks !

John.

Feb 10, 2009 | 1990 Jaguar XJ6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...