Question about 2000 Buick Century

1 Answer

No lighting for instrument cluster

Warning lights work but no lighting at night, now the gear indicator is also not glowing as well as the odometer you can see these faintly in daylight if you look hard so it is not broken.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 56 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Nissan pu speedometer quit working


SPEEDOMETER TROUBLESHOOTING


Can be loose speedo wiring connectors under instrument panel or its issue with speed sensor on transmission.


I suggest you to go through help links mentioned below with appropriate solutions to confirm the problem :------


How to trouble shoot speedometer?

http://schematicsdiagram.blogspot.com/2011/06/speedometer-not-working.html

-----------

1996 fiat bravo speedometer not working?

http://technoanswers.blogspot.com/2012/01/1996-fiat-bravo-speedometer-not-working.html
------------

Speedometer works but odometer not working?

http://technoanswers.blogspot.in/2012/01/speedometer-works-but-odometer-not.html

-----------

Speedometer runs backward?

http://technoanswers.blogspot.com/2012/01/speedometer-runs-backward.html

-------------

Warning lights on and speedometer died?

http://howtobyme.blogspot.com/2011/08/warning-lights-on-and-speedometer-died.ht

-------------

Speedometer not working on 1993 Ford F350?


http://repairhelpcenter.blogspot.in/2012/02/speedometer-not-working-on-1993-ford.html

----------

ABS & Brake lights warning indicator steady on dash and speedometer not working for Dodge Ram?

http://howtobyme.blogspot.com/2011/11/abs-brake-lights-warning-indicator.html

-----------

Vehicles Cluster panel Not reading Miles?

http://schematicsdiagram.blogspot.com/2011/12/vehicles-cluster-panel-not-reading.html

-------------

Odometer works properly but speedometer works intermittently?

http://technoanswers.blogspot.com/2012/01/odometer-works-properly-but-speedometer.html

-------------

These will help.

Thanks.

Feb 04, 2013 | Nissan Cars & Trucks

1 Answer

98 jetta error code p0101


Can be loose speedo wiring connectors under instrument panel or its issue with speed sensor on transmission.

I suggest you to go through help links mentioned below with appropriate solutions to confirm the problem :------

How to trouble shoot speedometer?

http://schematicsdiagram.blogspot.com/2011/06/speedometer-not-working.html

-----------

1996 fiat bravo speedometer not working?

http://technoanswers.blogspot.com/2012/01/1996-fiat-bravo-speedometer-not-working.html
------------

Speedometer works but odometer not working?

http://technoanswers.blogspot.in/2012/01/speedometer-works-but-odometer-not.html


-----------

Speedometer runs backward?

http://technoanswers.blogspot.com/2012/01/speedometer-runs-backward.html

-------------

Warning lights on and speedometer died?

http://howtobyme.blogspot.com/2011/08/warning-lights-on-and-speedometer-died.ht

-------------

Speedometer not working on 1993 Ford F350?


http://repairhelpcenter.blogspot.in/2012/02/speedometer-not-working-on-1993-ford.html

----------

ABS & Brake lights warning indicator steady on dash and speedometer not working for Dodge Ram?

http://howtobyme.blogspot.com/2011/11/abs-brake-lights-warning-indicator.html

-----------

Vehicles Cluster panel Not reading Miles?

http://schematicsdiagram.blogspot.com/2011/12/vehicles-cluster-panel-not-reading.html

-------------

Odometer works properly but speedometer works intermittently?

http://technoanswers.blogspot.com/2012/01/odometer-works-properly-but-speedometer.html

-------------
These will help.
Thanks.

Nov 27, 2012 | 2008 Volkswagen Jetta Wagon

1 Answer

No gear indicator, replaced cluster, odometer and PRNDL lights on, but no indicator light for gears. ????? Swapped out instrument cluster, gears displayed on other vehicle, (both instrument clusters)


I had a similar situation. No odometer, fuel gage, etc. Turned out to be loose connection in the relay box that is closest to the battery cables. I opened the box and reinserted the connections. It happened again and I took a hammer and gave the black box a whack and it started working again. I found that when the car is running, my wife behind the steering wheel an me under the hood, that when I manipulate the box she hears a click under the dash and the symptoms appear and disappear. That is where I would direct my attention. I understand it is a common problem on this model from a Buick mechanic.

Nov 06, 2012 | 2003 Buick Century

1 Answer

After disconnect and reconnect the battery of my opel antara, the indication of odometer displays only 888... for all indications. How can i reset it?


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2007 Opel Antara 2.0

1 Answer

My nissan Almera S reg has no side lights or dash lights.All fuses seem ok.


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2005 Nissan Almera 1.5

1 Answer

I have a 2004 Jeep Cherokee Laredo. An indicator (with a symbol of what looks like a radiator) below the low fuel indicator (bottom left had side of the dashboard) lights up and remains on. I have checked...


2005 Instrument cluster layout
2005_cluster_01s.jpg
1. Speedometer
2. Brake warning light
3. Turn signal indicator light
4. High beam indicator light
5. Malfunction Indicator Light (MIL)
6. Airbag warning light
7. Anti-Lock brake warning light
8. Tachometer
9. Security alarm indicator light
10. Oil pressure warning light
11. Electronic Stability Program (ESP)/
Traction Control System (TCS) indicator light
12. Tire Pressure Monitor warning light (base)

13. Temperature gauge
14. Electronic Vehicle Information Display
15. Tow/Haul indicator light
16. 4WD Low mode indicator light
17. Seat belt reminder light
18. Cruise control indicator light
19. Odometer/Trip Odometer
20. Transmission gear indicator
21. Fuel gauge
22. Electronic Throttle warning light (5.7 Hemi)
23. Front fog light indicator light
24. Voltage warning light

Jun 05, 2011 | 2004 Jeep Grand Cherokee

1 Answer

Changing dashboard light


Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Aug 09, 2010 | 1998 Plymouth Voyager

3 Answers

Speedometer stopped working


this vehicle has an electronic speed sensor located on the trans i do believe but im pretty sure this is your problem change it and your cured

Jan 15, 2010 | 2004 Chevrolet Blazer

1 Answer

I have a 2001 hyundai elantra and the warning lights on the dashboard. I know what the oil light looks like and the airbags. What are the other two lights.


Your best bet is to go HERE and signup for a free account then Downloading your Manual - service sheets, diagrams, parts lists etc.
Hyundai is one of the best with providing their customers with free information about the vehicles!!

I have D/L the manual, and the warning lamps on the instrument cluster are...
Left to right...(starting under temp. Gauge)

WITHOUT TRIP COMPUTER
11. Traction Control Indicator Light (If installed)

12. ABS Warning Light (If installed)

13. Seat Belt Warning Light

14. Oil Pressure Warning Light

15. Charging System Warning Light

16. Parking Brake/Brake Fluid Level Warning
Light

17. Malfunction Indicator Light (MIL)

18. SRS (Airbag) Warning Light

19. Trip Odometer/Odometer

20. Trip Odometer Reset Knob

21. Low Fuel Warning Light

WITH TRIP COMPUTER

7. Front Fog Indicator Light (If installed)

8. Door Ajar Warning Light

9. Trunk Lid Open Warning Light

10. Parking Brake/Brake Fluid Level Warning
Light

11. Malfunction Indicator Light (MIL)

12. Charging System Warning Light

13. Oil Pressure Warning Light

14. SRS (Airbag) Warning Light

15. Cruise Indicator Light (If installed)

16. Seat Belt Warning Light

17. ABS Warning Light (If installed)

18. Traction Control Indicator Light (If installed)

19. Automatic Transaxle Position Indicator Light
(Auto T/A only)

22. Low Fuel Warning Light


Thanks for using FixYa - a FixYa rating is appreciated!!

Feb 21, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
2000 Buick Century Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...