Question about Lexus Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Usually you just hold down the button in the visor, and while you're holding it down, aim your garage door opener at it and hold that button down so the frequency is grabbed by the built-in opener. That's how it worked in a few other cars that I've seen - try it out and see if it works for yours.
Posted on Sep 10, 2008
SOURCE: remote garage door opener
1. Position vehicle within 10 feet of garage door- engine off and battery on.
2. Press/hold 2 outside buttons of Homelink transceiver until red indicator starts flashing rapidly, then release button. This should take about 20 seconds. This erases any previously learned codes.
3. Press/hold remote control and press/hold button of Homelink transceiver simultaneously. Slowly move remote control from 5" away to 1" away from Homelink transceiver. Release both buttons after red indicator starts blinking rapidly. This should take about 5 seconds. I discovered that the Homelink in my TL is a bit faulty because it took much longer to accomplish this than when programming the Homelink in my MDX. My TL's Homelink may "unlearn" it's code in the future and the needed proximity of the TL to the garage door may be much closer than desired until I get the Homelink fixed.
4. Press training button on garage door opener unit until the indicator lights illuminates- this should be immediate.
5. Within 30 seconds press/hold the Homelink button for 2-3 seconds until the red indicator starts flashing rapidly. Repeat a second time. It should now be programmed. Check it by pressing the programmed button on the Homelink receiver.
6. When programming more than 1 garage door opener unit, disconnect power from unit before programming more units. By not doing this the programmed unit could conflict with the unprogrammed units commands.
1. The Battery in the garage door remote may be too weak to program Homelink. However, the battery may be strong enough to operate the garage door. One of my remote controls had a weak battery- my system was installed today, fresh out of the box. I had to use the second remote control for the programming of Homelink on my 2 vehicles.
2. Antenna on the garage door opener unit must be hanging down, fully extended.
Posted on Dec 08, 2008
my suggestion would be to make sure that the codes to the opener match the remote and I would stop by a Sears service center for assistance or a Ace hardware store
Posted on Jan 21, 2009
SOURCE: Program car to garage opener
on the garage door opener there is a button, that is called the" learning button "you press that button until light blinks, then within 20 seconds press the open button inside car.
Posted on Feb 01, 2009
SOURCE: remote garage door
drive away from your house and find a place to park. Take your garage door opener and hold it up by the openers on you van . Press the button that you want to operate you garage door and the original opener at the same time it should flash 2 or three times . Now you should be able to use the one that came with the car. (note: it will depend on the age of you garage door opener)
Posted on Mar 23, 2009
Tips for a great answer:
Jan 21, 2015 | Hyundai Cars & Trucks
Dec 08, 2014 | Cars & Trucks
Feb 02, 2013 | Cars & Trucks
Aug 28, 2012 | 2002 Volvo S60
May 28, 2012 | 2003 Lexus ES 300
Apr 19, 2011 | 2008 Mercury Milan
Aug 16, 2010 | 2004 Ford F150
Jan 30, 2010 | 2004 Lexus IS 300
May 07, 2009 | 2008 Lincoln Navigator
Jan 21, 2009 | 2000 Oldsmobile Bravada
78 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: