Question about Ford F

2 Answers

Power Steering Recently my power steering pipe blew and started leaking due to it comming in contact with the engine. Is it possible to remove and replace this pipe or is it a sealed unit to the steering rack?

Posted by on

  • 2 more comments 
  • Anonymous Mar 12, 2009

    It is a Fiesta 2002 1.25 Zetec SE Model (old shape)

  • yellowray Mar 12, 2009

    Car make is as above Ford Fiesta 02 1.25 Freestyle with Zetec SE engine

  • yellowray Mar 12, 2009

    It is the pipe running under the righthand side on the under side of the engine. It has been touching the bottom of the engine and seems to have melted.

  • Greg Bernett
    Greg Bernett May 11, 2010

    What year and model of vehicle?

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,984 Answers

It would be smarter to purchase a new pump....not worth the cost of labor to fix it. They run cheap...$65 or so.

Posted on Mar 12, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 507 Answers

If it's the low pressure side i'm sure a mechanic can replace just the broken part. if it's the high pressure side, best off just to get a new hose. if not, the hose is likely to leak again on the high pressure hose if the unit isn't replaced.

Posted on Mar 12, 2009

  • Steven Brock Mar 12, 2009

    i don't know that much details about fords. one line is bigger then the other on your power steering system. an auto parts store should be able to tell you which hose is high or low pressure. then using that you should be able to determin your course of action either splicing in a new piece of hose or tubing on the low pressure line, or by replacing the whole hose on the high pressure. if you do splice in, make sure to use some zip ties to keep the new hose from melting again.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why no power steering?


Possibly bad steering box

Dec 19, 2015 | Cars & Trucks

1 Answer

Power steering fluid leaking on 2002 pontiac grand prix


OK you know the problem but is it something as simple as replacing the Power steering hose or as complicated as also needing a new power steering pump also? Look at where its leaking to determine what needs replacing. Remember it just takes a little time to determine where its leaking. If you find that its not the hose leaking but its the power steering pump then follow these easy steps and save $100s doing it yourself:
1 Remove the negative battery cable with a wrench and place it aside. Remove the upper strut housing tie bar if necessary for access. Remove the power steering serpentine drive belt and electrical plug on the TFE off as applicable. Remove the lower bolt from the mounting bracket using a socket and ratchet if necessary for access. Take off the inlet and outlet hoses from the power steering pump. Remove the reservoir hose only on the supercharged engine. You will need a flat-head screwdriver for this task.
2 Place the power steering pump pulley so the bolts can be accessed through the hole in it. Remove the mounting bolts, using a socket and ratchet, through the hole in the pulley. Take the power-steering assembly out from the bracket. If necessary transfer the pulley to the new pump with a pulley puller.
3 Replace the power steering pulley assembly before you install the pump using the pulley-install tool from your kit. Start the power steering inlet hose connection to the pump by hand. Replace the power steering pump assembly to the engine. Replace the lower bolt first, making sure the hose and heater pipe have enough clearance so they do not touch. If the two rub together they will make noise after the installation is finished. Replace the outlet hose to the pump, directing the hose under the engine harness and the heater hose. If the engine is supercharged it will be necessary to connect the hose from the reservoir.
4 Torque the power steering gear inlet hose to 20 foot-pounds and the hose clamp at the pump to 15 inch-pounds. Torque the pump mounting bolts to 20 foot-pounds. If equipped with a TFE pump, attach the connection. Replace the power steering drive belt or serpentine belt if you removed either. Replace the upper strut tie bar and torque the nuts to 18 foot-pounds. Replace the negative battery cable and fill the power steering reservoir with fluid. Bleed the steering system by starting the engine and turning the steering wheel right and left until all the air is out.

Apr 20, 2014 | 2002 Pontiac Grand Prix

1 Answer

How to change vane pump o/h kit


FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

Mar 07, 2011 | 2000 Honda Civic

1 Answer

After I replaced the power steering pump and reservoir on my 2002 Jeep, I still get air in the system. Where could it be coming from?


Your problem could be a pressure side hose that has a rupture that only leaks in extreme conditions. Inspect to replace with new to repair problem. First make sure you have removed the pump caps off of the hose fittings. If ok, it appears you may have a stuck valve in the rack assembly. Replacing the rack should solve your problem. ------- The new pump should be self-bleeding by turning the wheels left and right. Let sit over night to release air bubbles, recheck fluid level.------ Check the tension of the drive belts on the pump, as they may be loose. The power steering pump and reservoir is located on the front of the engine driven by one of the fan belts. There is a removable cap on the top with a dipstick attached. With the engine off, fill this up to the full mark with power steering fluid. Replace the cap, start the engine and check for leaks. On the back of the pump are two hoses either one could be leaking. REPAIR PROCEDURE:
1. Wipe the power steering cap and area free of dirt. Remove the power steering cap.

2. Use a siphon pump to remove as much fluid as possible from the power steering fluid reservoir.

3. With a helper in the vehicle, raise the vehicle on an appropriate hoist.

WARNING :POWER STEERING FLUID, ENGINE PARTS, AND THE EXHAUST SYSTEM MAY BE EXTREMELY HOT IF THE ENGINE HAS BEEN RUNNING. DO NOT START ENGINE WITH ANY LOOSE OR DISCONNECTED HOSES. DO NOT ALLOW HOSES OR POWER STEERING FLUID TO TOUCH HOT EXHAUST MANI FOLD OR CATALYST.
4. Locate the power steering cooler attached to the crossmember support plate. Slide back the clamp and disconnect one of the two power steering return hoses at the power steering oil cooler and drain fluid in an appropriate container.
5. Have the helper turn the steering wheel back and forth quickly several times to force as much fluid as possible from the steering gear.
6. Reconnect the hose at the oil cooler using the original clamp.
7. Lower vehicle so the vehicle tires are not contacting the ground.
9. For proper fluid fill and bleeding air from the power steering system:

a. Fill the power steering reservoir to the top of the fill range using Mopar power steering fluid (ATF+4) p/n 05013458AA.

b. With the engine OFF and the vehicles tires off the ground, slowly turn the steering wheel back and forth (lock to lock) slowly 20 times to force fluid into the steering gear.

c. Fill the power steering reservoir to the top of the fill range.

d. Start engine and let run for a few seconds, then turn oft engine.

e. Check fluid level and add if necessary.

f. Start engine, and slowly turn the steering wheel lightly contacting the left and right stops.

g. Stop the engine and check fluid level. Add fluid if necessary.

h. Lower vehicle, start engine and slowly turn steering wheel lock-to-lock.

I. Stop engine and check fluid level. Add fluid if necessary.

j. If fluid is extremely foamy, allow vehicle to stabilize a few minutes, then repeat steps "i" and "j" until the fluid level remains constant after running the engine and turning the steering wheel from lock to lock.

10. Inform the vehicle owner/operator that a steering vibration may be noted for a few hundred miles until the air is completely removed from the steering system.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Jan 26, 2010 | Jeep Grand Cherokee Cars & Trucks

3 Answers

How do you remove the Power Steering Pump and bracket. I have taken off several bolts but it still is not letting loose. Help


3.0L (VIN 3) Engine

f799ffc.gif
Power steering pump mounting detail (3.0L engine)

  1. Disconnect and isolate the negative battery cable.
  2. Remove the accessory drive belt. The belt does not have to be removed from the engine.
  3. Raise and safely support the vehicle.
  4. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  5. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  6. Place a drain pan under the power steering pump. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  7. Remove the accessory drive belt splash shield.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 2 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly out from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 2 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the 2 support bracket mounting bolts to 40ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

3.3L (VIN R) & 3.8L (VIN L) Engines

0b3de97.gif
Rear support bracket mounting detail (3.3 & 3.8L engines)

6764c64.gif
Power steering pump mounting detail (3.3 & 3.8L engines)

  1. Remove and isolate the negative battery cable.
  2. Raise and safely support the vehicle. Place a drain pan under the power steering pump.
  3. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  4. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  5. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  6. Remove the accessory drive belt splash shield.
  7. Remove accessory drive belt.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 3 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 3 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the support bracket mounting bolts to 40 ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. Torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

Nov 03, 2009 | 1997 Chrysler Town & Country

1 Answer

HOW TO REPLACE A POWER STEERING HOSE


FIRST OF ALL YOU HAVE TO REMOVE POWER STEERING FLUID.USING A SUCTION GUN OR LARGE SYRINGE.REMOVE MUCH FLUID AS POSSIBLE.WHEN DONE REMOVING POWER STEERING FLUID.YOU NEED A INLINE WRENCH AND OPEN BOX END WRENCH TO REMOVE THE POWER STEERING HOSE.YOU HAVE TO REMOVE POWER STEERING LINE FROM THE RACK.UNDER THE CAR SAFELY RAISE AND SUPPORT VECHICLE. THEN REMOVE THE TIRE OR WHEEL.THEN REMOVE THE INNER FENDER SPLASH SHIELD.ITS GOING TO BE A TIGHT FIT AND HARD PLACE TO GET YOUR HAND TO REMOVE THE POWER STEERING LINE FROM BOTTOM.WHEN DONE.MAKE SURE NEW POWER STEERING HOSE OR LINE HAS NEW O RINGS.WHEN INSTALLING THE THE NEW STEERING HOSE.WHEN ALL IS DONE BLEED POWER STEERING SYSTEM. FILL UP POWER STEERING PUMP TO CORRECT FLUID LEVEL.THEN LET IT SET FOR 2 MINUTES UNDISTURBED.THEN START THE ENGINE RUN IT FOR 2 TO 3 SECONDS.ONLY CHECK THE RESERVOIR AND ADD MORE FLUID AS NECESSARY.REPEAT THE OPERATION UNTIL THE FLUID LEVEL REMAIN CONSTANT.NOW RAISE FRONT OF THE CAR UNTIL THE WHEELS CLEAR THE GROUND START THE ENGINE AND INCREASE THE SPEED TO ABOUT 1500 RPM.NOW TURN THE STEERING WHEEL GENTLY FROM STOP TO STOP CHECK THE FLUID LEVEL.LOWER THE VECHICLE TO THE GROUND WITH ENGINE STILL RUNNING MOVE THE CAR FORWARD SUFFICIENTY TO OBTAIN FULL RIGHT LOCK FOLLOWED BY FULL LEFT LOCK BUT DONT HOLD THE SREERING WHEEL FIRMLY AGAINST THE STOPS.RECHECK THE FLUID LEVEL IF THE FLUID IN THE RESERVOIR IS EXTREMELY FOAMY ALLOW THE CAR TO STAND FOR A FEW MINUTES.WITH ENGINE OFF.WHEN JOB IS FINISH. WARNING DONT DRIVE CAR ON ROAD IF YOUR FLUID STILL FOAMY OR POWER STEERING PUMP MAKE NOISES.REBLEED THE SYSTEM AND CHECK FLUID LEVEL AND CHECK FOR LEAKS.DONT DRIVE CAR UNTIL YOU START FEELING NORMAL STEERING.IF YOU HAVE TROUBLE DONT DRIVE.HAVE IT TOWED TO THE NEAREST GARAGE.

Oct 05, 2009 | 1999 Oldsmobile Alero

1 Answer

Loud noise in the steering column;gear box replacd recently


Dealer, but did you check the Power steering fluid level??or any leaks. There are two hose that connect to the gear box from the power steering pump. if the pump is low on fluid you lose your power steering, if the hose has a leak or it blew and lost the power steering fluid then you lost your power steering again. 
Check the fluid level to the power steering pump and any leaks or broken hose to the gear box.
Keep me posted, be glad to help and good luck.

May 31, 2009 | 2002 Chevrolet Tahoe

2 Answers

How to change inner tie rod ends?


if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------
  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Apr 15, 2009 | 1997 Ford Windstar

2 Answers

My power steering pressure hose has a leak.


i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE
  1. Remove the power steering pressure hose (2) from the power steering pump (1).
  2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
  3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
  4. Remove the power steering pressure hose (1) from the power steering gear (3).
  5. Remove the power steering hose retainer (2).
  6. Remove the power steering pressure hose (1) from the vehicle
    1. Install the power steering pressure hose (1) to the vehicle
    2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
    3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
    4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
    5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Mar 27, 2009 | 1999 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...