Question about 2009 Mazda CX-7

Open Question

Rear camber how do you adjust the rear camber on a mazda CX-7?

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2008 Mazda Cx 7 Grand Tour: Tires rotated, basic 4

I have a 2007 CX-7 and my vehicle did the same thing. There is a Technical Service Bulletin on the the problem that explains how to correct the pull. It basically states that the technician has to rotate the position of the strut mount on the left side 180 degrees to the right which should lower the left side caster angle. Any good alignment shop will know that the right side caster angle should be .5 degrees higher on the right to compensate for the crown of the roadway. For example my readings were 3.2 on the left and 2.8 on the right. This is reversed and is why my car pulled to the right. After the strut mount was rotated my reading were 2.4 on the left and 2.8 on the right. That all but eliminated the pull. Verify your caster readings on the alignment printout. If this was already done then there isnt much more that can be corrected. Mine still has a slight drift to the right.

Posted on Dec 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 cx-7 has oil leak but oil is full??drives fine no smell has 113,000 mile on it and never a problem


Have the engine cleaned top and bottom with a pressure washer and once that is done drive the car about 10 miles return to the shop and check for the oil leak source, common placed for leaks are valve covers, rear main seals and the oil pressure sensor. It is best that you have access to a car lift.

Mar 23, 2017 | 2009 Mazda CX-7

1 Answer

How to adjust headlights


In my CX-9 on the left side of the drivers dash, below the steering wheel, there is a little adjustment wheel for headlight up and down adjustments. I believe it has 3 or 4 positions. Check out the video at 1:13 mins in.
2011 2007 Mazda CX 9 Automatic Xenon Exterior Lights Tutorial

Jun 02, 2014 | 2007 Mazda CX-9

1 Answer

How do i correct Rear camber on 2002 Lincoln ls


I don't think this vehicle is equipped with provisions allowing a camber adjustment in the rear. If there are adjustments provided, there will be cam bolts in the lower control arms for adjustment. If there are no adjustment bolts, and the camber is out, usually there will be something bent. Also check rear ride height which can affect camber for a broken spring.

Jul 01, 2012 | Lincoln LS Cars & Trucks

1 Answer

How to adjust camber on 2001 monte carlo


There is no camber adjustment from the factory,however moog sells a camber bolt kit that will allow for adjustment. About 20 bucks . If you are talking about the rear of the car,ride height makes a drastic change in camber. If the springs start to get weak the camber will go negative,spring spacers will correct this.

Jan 07, 2011 | Chevrolet Monte Carlo Cars & Trucks

2 Answers

PROGRAMMING THE GARAGE OPENER ON MY REAR VIEW MIRROR ON A 2007 MAZDA CX7


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

May 12, 2010 | 2007 Mazda CX-7 Grand Touring

1 Answer

Unable to fuel up


I think you are correct in assuming it's the vent tube that goes back to the filler spout, and it's probably kinked or something. I have had to repair a few cars with this problem, but it isn't common. Thanks for the information about the rear camber - they aligned it really well at the factory :) Rick

Apr 15, 2009 | 2004 Mazda 3

2 Answers

Mazda 5


You might see if there is a camber caster shim pack that can be added.

May 14, 2008 | 2007 Mazda MX-5 Miata Touring Convertible

Not finding what you are looking for?
2009 Mazda CX-7 Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...