Question about 2009 Nissan Murano

Open Question

Size socket needed remove axle nut - 2009 Nissan Murano

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: i need to change an axle in a 1993 nissan altima

the axle nut should be a 36mm
will also need a 17mm to remove three bolts holding ball joint to control arm and a pry bar to pop axle out of transmission. if replacing right side will need tounhook support bearing

Posted on Oct 10, 2008

  • 41 Answers

SOURCE: what is the size of nut that retains bearings mm?

if its a 2wd truck they shouldnt be that tight as they are kept in place with a cotter pin, i usually just use a cresent

Posted on Nov 22, 2009

  • 1453 Answers

SOURCE: want to remove front axles

A size 36mm impact socket is used to remove the front axle nut from the hub.

Posted on Feb 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tools needed to change cv axle in 2004 kia optima


32 mm socket for axle nut, ratchet, needle nose pliers to remove axle nut cotter pin, 14 mm for brake calipers, not exactly sure what the tie rod bolt size is, but it would probably be in a metric socket set if its not a 14mm

Apr 07, 2017 | 2004 Kia Optima

1 Answer

What size axle nut for 2000ford taurus se


Axle nut size? - Taurus Car Club of America : Ford Taurus Forum

www.taurusclub.com > ... > Suspension, Handling and Brakes
Jul 23, 2011 - 8 posts - ‎5 authors 1996 Mercury Sable front axle nut. I have read that the size is 30mm but the socket that I rented (30mm in a ... 2000 Duratec SE White Wagon Axle nut torque question. - Taurus Car Club of America ...
11 posts
May 4, 2012
CV Axle nut size
11 posts
Dec 9, 2011
Why Does The Axle Nut Need Such A Big Torque
11 posts
Dec 7, 2009
2000 Ford Taurus Front Wheel Bearing And Half-axle ...
11 posts
Apr 18, 2009
More results from www.taurusclub.com

Sep 28, 2015 | Cars & Trucks

1 Answer

What size socket do i need for the drive axle/hub nut for a 1997 Chevrolet Cavalier?


I think that one is a 32mm...could b wrong tho..
I'd grab my 32 and 36 if I were going to take it off without looking

Sep 02, 2014 | 1997 Chevrolet Cavalier

1 Answer

Axle nut size


Measure the nut & divide by .0395 to get metric mm

34,35 or 36 mm are the most common

Mar 18, 2014 | Cars & Trucks

1 Answer

Front axle 2002 highlander


to remove front axle.to loosen front axle nut leave vechicle weight on wheel then just loosen front axle nut because axle nut torque at 217 ft lbs torquehard to loose axle nut with vechicle weight off wheel.okay. you need a 1/2 breaker bar and axle socket to loosen axle nut dont use 12 points sockets need go auto parts store buy right socket for axle nut.okay when you loosen front axle nut you need safely raise support vechicle. need to remove wheels remove fender apron seal remove transaxle fluid remove transfercase oil if you have 4WD.remove hub nut remove stabilizer bar link remove speed sensor remove tie rod end remove lower arm from the ball joint then slide the halfshaft from the hub then carefully pry the shaft from the transaxle.then install new front axle push in make sure front axle snap ring on front axle snap in place inside transmission just pull a little on front axle make its in place. when all done tighten front axle much as you can then when done putting every thing back in place.lower vechicle need torque front axle nut to 217 ft lbs.

Jan 12, 2013 | 2002 Toyota Highlander

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

1 Answer

How do i repair left front hub & bearing assembly on a 2000 ford taurus v6 24v dohc


BEST TO GET A HAYNES REPAIR MANUAL IT HAS PHOTOS AND INSTRUCTIONS ON HOW TO REMOVE HUB BEARING ASSEMBLY.YOU WILL NEED A 1/2 SIZE TORQUE WRENCH FOR HUB RETAINING NUT.ITS TORQUE IS 170 - 202 FT LBS.MAKE SURE YOUR TORQUE WRENCH MAXIMUM RANGE IS AT LEAST OVER 200 FT LBS TORQUE.YOU WILL ALSO NEED A AXLE NUT SOCKET.ITS A BLACK SOCKET LIKE IMPACT SOCKET.ITS GRADE 8 STEEL.YOU HAVE TO USE THIS TYPE.A REGULAR SOCKET WILL BREAK.WHEN REMOVING AXLE NUT.ITS ON TIGHT.YOU WILL ALSO NEED A 1/2 BREAK BAR TO BREAK IT A LOOSE.ALSO REMOVE WHEEL COVER.WITH CAR WEIGHT ON WHEEL YOU HAVE TO LOOSEN AXLE NUT A LITTLE.NOT ALL THE WAY UNTIL YOU GET CAR OFF GROUND.WORK SAFE BECAREFUL.

Oct 28, 2009 | 2000 Ford Taurus

Not finding what you are looking for?
2009 Nissan Murano Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...