Question about 1999 GMC Sierra

2 Answers

How do you bleed brakes on a 1999 GMC Sierra with ABS 2wheel drive 1500 series

Posted by on

  • Anonymous Mar 13, 2014

    hooking the cable harness
    together

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

The rule of thumb is to start as far away from the master cylinder as poss. so it means you start at the right rear, left rear, right front, then at last left front. There is a little a little weep bolt on each calliper it needs to be un lossened when break is fully applyed then tighten weep bolt back up pump the breaks while weep bolt is still tight then hold brake pedal down to floor lossen weep bolt till a full steam of fluid comes out tighten bolt back up, now move on to the next break calliper and repeat this same proccess till you finished. Hope this works better than r/r l/r r/f l/f lol!!!!

Posted on Apr 06, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

Start with r/r then l/f then l/r then r/f

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put new brake lines on a 2000 GMC Sierra 1500 4 wd and no fluid to back brakes, shop forced abs to come on and still very little fluid ... what is going on ?


Hello and good morning Vivian ,I looked over what you were saying PLEASE go to auto zone site and log it(its all free) then list your truck in my vehicle and open repair guide go to brakes and READ there is a chapter on ABS and how to bleed brakes .I really hope this gets you on track and solves your problem.

Oct 18, 2014 | Cars & Trucks

1 Answer

How do you bleed the abs controller on my 2003 Gmc sierria 4WD 5.3L


i usually bleed them by taking it out to a gravel or dirt road and doing about 10 - 20 skidding stops that activate the abs motor and it pumps the air out by itself.

Mar 06, 2011 | 2003 GMC Sierra 1500

1 Answer

What special tool is need to bleed brakes on 1999 gmc sierra? Had to replace all lines due to rust. I can only get the front driver side to bleed. The brake peddle is like steeping on steel. ...


You can actually bleed each caliper at the brake line connection to the caliper...you will need someone to depress the brake pedal, or you can borrow the auto bleed brake pedal tool from your local auto parts store...sounds like you can fix this yourself...the symptom says..."air in lines"...Hope this helps.

Feb 21, 2011 | 1999 GMC Sierra

2 Answers

Hello sir.. i am bleeding the brakes in my 99 gmc sierra, i have replaced all the brake lines minus the two lines in the rear that route to a t, now from past this all the lines are new, everythings tight,...


U need a special tool that holds the poppet valves open in the ABS hydraulic control unit to bleed the brakes of air, without it u CAN'T get the air out of the system.

Sep 28, 2010 | 1999 GMC Sierra

1 Answer

1994 gmc Sierra. Poor, soft, spongey peddle feel


well maybe the lines are not bleed right. did you bleed the master??

May 09, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

When braking on hard surface, just before dead stop, the last few feet, the ABS brakes takes over and the veh caries on a few more feet, finishing with a slow stop. The 4 wheels braking system were bled...


There was a TSB on this issue with your Sierra, a faulty or dirty ABS sensor is the cause of this problem. The fix is simple, just clean the ABS sensor at the front hub with brake parts cleaner and inspect the wire leads. At worst you may have to replace the sensor it self. Good luck

Feb 17, 2010 | 2003 GMC Sierra 1500

1 Answer

1997 GMC Sierra 5.7 changed master cylinder calipers and brake pads. I have a hard pedal until I turn the truck on and the pedal goes to the floor? Is there something I am missing? I have bled the brakes...


check under your master cylinder,is there another clyinder below with one line in and one line out,if you do I found this is for the Abs to the rear,I had to replace this it was full of air,and did exactly what yours is now

Dec 06, 2009 | 2003 GMC Sierra 1500

Not finding what you are looking for?
1999 GMC Sierra Logo

977 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...