Question about 2005 Renault Kangoo 1.5

Open Question

Renault 1 5 dci kangoo van

Red button beside the battery got pressed, how do I reset it.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Richie_asg1
  • 1036 Answers

SOURCE: renault clio 1-5 dci (2002)

Hi there!

It's very likely a valve stem seal that has split. This will allow oil into the cylinder from the crank gallery.

Off with it's head! I'm afraid.

The only other thing it can be is overfueling - but then it will be sputtering and lagging on acceleration.
You can check which cylinder is affected by removing the plugs and looking for the oily one. They will all need replacing really as it's false economy to do just 1. The seals are cheap. I would get a new cambelt fitted at the same time - as it has to come off anyway.

(If this leads to a solution, please take the time to rate as Fixya! - Thank you)

Posted on Jun 17, 2008

  • 1 Answer

SOURCE: renault kangoo 1.9 d immobiliser probims.{2001} model.

hold the central locking button down on the centre consul inside the van for more than 5 seconds the doors should lock Then unlock,then press the key fob within ten seconds the doors will lock and unlock again this will re- program the key code

good luck jk

Posted on Feb 05, 2009

  • 1 Answer

SOURCE: replace cv boot on a renault kangoo

Did one today, assuming drive shaft removed take off large clip from inner boot slide back joint socket comes away leaving the knuckle joint on the shaft remove 19mm circlip and tap knuckle off spline this allows outer boot to come back - easy enough. Not much tubber to secure new clip over boot though especially with all the grease.

Posted on Jun 10, 2009

  • 101 Answers

SOURCE: Torque setings

if it is a solid bearing do it up as tight as you can.if it is a tapered bearing do it up untill the nut is touching the bearing check the hub for play if you have got play do the nut up a bit more until the play is gone in the hub.make sure you do not over tighten the bearing or the wheel will not turn freely.the wheel needs to spin with no drag.

Posted on Jul 31, 2009

  • 271 Answers

SOURCE: renault kangoo 1.4 petrol Auxiliary belt diagram

17d60e8.jpgGo ahead

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone knows where engine number for Renault kangoo van dci is located pls help!!!!!!


If you go to the Renault Kangaroo Forum in the link below and post your question politely I am sure one of the guys there will be able help you with that one.


Kangoo Renault Forums Independent Renault forum

Jan 03, 2016 | Renault Cars & Trucks

1 Answer

Hi I need help locating engine number for my renault kangoo dci 70


If you go to the Renault Kangaroo Forum in the link below and post your question politely I am sure one of the guys there will be able help you with that one.

Kangoo Renault Forums Independent Renault forum

Jan 03, 2016 | Renault Cars & Trucks

1 Answer

Where to look for engine number renault kangoo van dci pls help car must go for datadot


If you go to the Renault Kangaroo Forum in the link below and post your question politely I am sure one of the guys there will be able help you with that one.


Kangoo Renault Forums Independent Renault forum

Jan 03, 2016 | Renault Cars & Trucks

1 Answer

I have a renault kangoo 1.5 dci, 2005. The stop engine light flashes and the car wont start. No power at the injectors. Do i need to reset the chip key? If so how? There is no button on this key.


run the fault codes first to see if the immobiliser is at fault. IT could be a cam/ crank position sensor or a sensor that sets off the engine light to protect the engine and gear box.

Feb 18, 2014 | Renault Kangoo Cars & Trucks

1 Answer

Hello had my Renault kangoo 1.5 dci engine light came on and the 1 beside it that says their is water in the fuel its in limp mode now any tips cheers


check negative battery terminal for a broken wire! and drain the filter test it again. water in fuel should not make limp mode

Oct 17, 2013 | Renault Clio Cars & Trucks

1 Answer

Renalt kangoo van 2009 how do you reset


Service reset:
1. Press and hold the reset button [A]. See the picture below.

tdisline_719.jpg
2. Keep the reset button [A] pressed for 10 seconds.
3. The new service interval appears on the display.
4. The service indicator has been reset.

Jul 05, 2011 | Renault R5 Cars & Trucks

1 Answer

Had a new turbo fitting last week only got the van back seems to be a tapping noise coming from the engine stops some times when i change gear . some 1 said injectors or tapits havent a clue the van is a...


Did they also change oil to a heavier weight? Turbos are oil cooled and require heavier oil to extrude heat. Check with folks who did turn install and if they didn't I think an oil change is needed.

Mar 03, 2011 | Renault 181 Cars & Trucks

Not finding what you are looking for?
2005 Renault Kangoo 1.5 Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

xxxxxx xxx

Level 3 Expert

4834 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...