Question about Cars & Trucks

Open Question

Ford Mustang 2008 V6 location of pcv valve - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 92 Answers

SOURCE: 1998 Ford Explorer sport 4.0L 4x2 PCV Valve Location

the pcv is located on the rear(firewall) of the drivers side valve cover.turn counterclockwise and pull to remove be careful there are 2 small tabs inside the pcv hole in the valve cover(can feel with small finger) this is to hold valve in place so it wont leak.if you have a oil leak at the pcv a quick fix is to put a small amount of silicone around the pcv o-ring and install.wait hours for silicone to set up.

Posted on Oct 21, 2008

Handy Mike
  • 6 Answers

SOURCE: how do i replace the pcv valve on a 2000 explorer xlt v6 sohc?

On the passenger side of the intake manifold, coming off the bottom about the center of the engine front to back, you'll feel a hose that comes off a nipple. That hose makes a 90 degree bend and goes around to the rear of the motor. Where that hose meets the Y-connector from the other side of the intake you'll find the PCV valve. It's almost impossible to see it with the hood installed, and even tougher to reach it.

A good source of information for Ford Explorers can be found here

Posted on Oct 25, 2008

chrischronic
  • 235 Answers

SOURCE: 2002 LINCOLN LS V6 3.0 PCV VALVE LOCATION

it is down under the intake manifold. the intake manifold must be removed to get to it. this vehicle is known for developing a vacum leak in the elbow hose that connects to pcv valve, so ive done a few.

Posted on Feb 19, 2009

  • 1 Answer

SOURCE: pcv valve :where is it located on a 1999 ford explorer sport 2wd

It is located at the back of the engine near the fire wall. It is gray with a T connector at the top with two hoses coming off of the T and going forward into the intake manifold.

Posted on Mar 07, 2009

  • 2692 Answers

SOURCE: Can't find PCV valve on 2000 Chevy Impala 3.8 V6

PCV . Positive Crankcase Ventalation Valves are always located in the valve cover pans with a hose attached usually leading to the air cleaner, or some other vacuum source..

Posted on Jun 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4.6 Engine valve train in 2008 Ford Mustang Gt


    mages for 4.6 Engine valve train in 2008 Ford Mustang Gt


    More images for 4.6 Engine valve train in 2008 Ford Mustang Gt

    2005-2009 Mustang Cylinder Heads & Valvetrain ...

    www.americanmuscle.com/mustang-valvetrain-0508.html
    They help your motor breathe better and also make sure your Mustang gives top-notch throttle response. ... 2005, 2006, 2007, 2008, 2009 Mustangs; V6, GT, Bullitt, Shelby GT500, ... 2005-2009 Mustang GT Cylinder Heads & Valvetrain Components ... (6).Ford Racing SOHC 3V 4.6L Head Changing Kit (05-10 GT) $76.00.

    Mustang Camshaft Facts & Technical Information ...

    www.americanmuscle.com/camshaft-tech-guide.html

Feb 08, 2016 | Ford Cars & Trucks

1 Answer

Location of pcv valve on 2008 ford taurus 3.5


On 3.5L engines, the PCV Valve is located on the rear valve cover (see pictures bellow). Please note: the PCV valve must be replaced if it's removed. Access to the valve is easier if you remove the upper intake manifold. However, this is not absolutely necessary and if you are already a little mechanically inclined you can do it the way you would replaced any other PCV valve.

    -A 19mm open wrench will make your life a lot easier if the PCV valve is a bit tight. It is in an awkward spot to apply pressure.

    -Disconnect the electrical connector from the valve. There is a small pin or locking device on the wire that you will have to slightly depress for the connector to release.

    -Disconnect the hose from the valve and turn the hose clockwise so that you have a bit of room to work with.

    -Turn the PCV valve counterclockwise and remove from the valve cover. Pay close attention to the position of the valve at the point when it is to be removed. The new PCV valve will go in at that same position. Why is this important? It is possible to install the PCV valve facing in the opposite direction. Once the PCV valve in and locked it in place, it damages the locking mechanism. Therefore, if you remove it you will have to throw it away and purchase a new one.

    -You just saved $130 - $150 to have the PCV replaced at the dealership...

location-pcv-valve-2008-ford-taurus-3-5-cgnwdhiy0mxwbb3xg5zhzgxj-5-0.jpg

Apr 07, 2013 | 2008 Ford Taurus SEL

1 Answer

Specify were the pcv valve is located on 95 mustang v8?


Look on top of the block at back by firewall for PCV. Other things you may want to check/clean are idle air control valve on side of throttle body, as well as mass air flow sensor in intake air assembly. Clean IAC with throttle body spray cleaner and port it is removed from well, and try. Use tuner cleaner or electrical cleaner on MAF sensor . Sometimes just cleaning will cure it.

Apr 09, 2012 | 1995 Ford Mustang GT

1 Answer

Location of the pcv valve on a1993 ford mustang LX 2.3 litre engine


Both of you are wrong...it is a hose connected to the engine block under the intake manifold at the front of the motor and snakes back to come out under the intake manifold and the PCV valve plugs in there.

Apr 07, 2012 | Cars & Trucks

1 Answer

Location to the pcv valve on a 1998 ford mustang 4.6L


passenger side valve cover underneath the intake tube. test by replacing with a new one and seeing if problem is fixed.

Mar 26, 2012 | 1998 Ford Mustang

1 Answer

Where is the pvc valve located on the 2004 mustang gt?


The PCV is located on the passenger side valve cover under the intake tube coming from the air filter.

Aug 22, 2011 | 2004 Ford Mustang

1 Answer

I need to find where the pcv valve is located on a 1994 ford mustang GT


The PCV is located on the passenger side valve cover.

Aug 04, 2011 | 1994 Ford Mustang

1 Answer

Im looking for the pcv valve o a v6 ford f150 2004


The PCV valve is located on the passenger's side valve cover under a plastic bracket on top of the intake manifold halfway back

Nov 09, 2009 | 2004 Ford F150

3 Answers

Where is the pcv valve located on a 1999 ford explorer? Is there a picture?


PCV BasicsPCV stands for Positive Crankcase Ventilation.
All car engines have a PCV valve and it is located on top of the motor's valve cover. There is a vacuum line attached to it. It pulls out of the valve cover and if you shake it, you should hear a marble knocking inside it. If you shake it and don't hear anything, it's bad. It costs less than 5 bucks to replace.

Location
  • 4.0L is located in the valve cover near the brake booster

  • 5.0L is located behind the intake manifold (engine rear)

Oct 04, 2009 | 1999 Ford Explorer

2 Answers

Have oil in my radiator fluid reservoir tank. Let a friend due a tune-up on car and i gave him a pcv valve to put on car he put it on the left valve cover in rear (if looking at car) in my book it shows...


someone has just reversed the valve covers swapped them from one to the other as far as the oil concern, sounds like you either have a leaking trans cooler in radiator or you have a blown head gasket

Mar 10, 2009 | 1993 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...