Question about 2003 Jeep Grand Cherokee

Open Question

Diagnostic code 0530 2003 jeep grand cherokee

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 323 Answers

SOURCE: Jeep Grand Cherokee Limited P0700 diagnostic problem

P0700 means there is a transmission fault code in the transmission controller. Since the transmission controller doesn't have a light attached, it tells the engine controller to turn the light on using this code. You'll have to access the transmission controller to further diagnose the problem.

Posted on Jun 14, 2009

Ad
  • 94 Answers

SOURCE: 2004 Jeep Grand Cherokee. Keeps stalling, engine

P0505 means the whole Idle Control system, not only the IAM. Check all related sensors (i.e. crankshaft sensor). Check with a voltmeter direct at the connector of the IAM if you get any signal. Remove the IAM from the TB, connect him, let someone switch your ignition key to ON. The IAM need to drive in/out for a short time to find the right position. Hold the IAM near a hard part, that they cant drive out completely! If IAM works fine, check the fuel pressure, check and clean your TB ( if not done yet). If that doesn't work, come back again please

Posted on Oct 27, 2009

  • 52 Answers

SOURCE: 96 Jeep Grand Cherokee diagnostic codes P1762 and

governor pressure sensor in transmission is the likely problem

Posted on Nov 22, 2009

calilourw1
  • 12 Answers

SOURCE: 2003 Jeep Grand Cherokee Laredo - Code P0456 EVAP leak

open hood and ck for broken vacuum hoses going to the purge valve(2 vacuum ports and a wiring connector)
on the drivers side between airbox and firewall
if good remove driver side rear tire and inspect hoses next to the gas tank and 3rd, the canister is in that wheel well also insp for cracked hoses there also, been working for jeep 12 years i charged people about 1 hour to correct this probem.

Posted on Dec 18, 2009

Testimonial: "Thanks!"

  • 3640 Answers

SOURCE: 2002 jeep grand cherokee with 4.0 engine will die but restart

p0340 is the cam shaft sensor, this will cause it to cut off while driving, hardtime starting, p0351 is the ignition coil A primary/secondary curcuit mal function. p1391 is ignition system misfire, this could be plugs, wires, or coils. first of all have the cam sensor changed and it may correct the rest of the codes. when fixed turn light off with obd2 scanner. if you do not have one, then any auto parts store will erase the codes fo free of charge.

Posted on Jan 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is diagnostic code 22 for a 1994 Jeep Cherokee grand limited


That code is for the engine coolant temperature sensor. "...input above maximum acceptable voltage." I would try a new temp. sensor. If that doesn't fix it, you may need to have an engine scanner hooked up, and see what the sensor is sending to the computer, and go from there.
A bad coolant temp. sensor can cause hard starting like your symptoms.
.

Apr 25, 2014 | 1994 Jeep Grand Cherokee

1 Answer

I am getting diagnostic code 22


Error Code: 22
Description: Engine Coolant Temperature circuit malfunction.
Possible Causes:
- Wiring.
- Coolant Temperature sensor defective.
- ECM.

Apr 25, 2014 | 1993 Jeep Grand Cherokee

1 Answer

Code 463 fuel level sensory high imput, what is this and where is it located


Not sure if this helps or not, but here is information from the 1998 Jeep Grand Cherokee Service Manual, ezg_25.pdf, page 6 of 20…

Hex Code = 95
Generic Scan Tool Code = P0462
DRB Scan Tool Display = Fuel Level Sending Unit Volts Too Low
Description of Diagnostic Trouble Code = Open circuit between PCM and fuel gauge sending unit.

Hex Code = 96
Generic Scan Tool Code = P0463
DRB Scan Tool Display = Fuel Level Sending Unit Volts Too High
Description of Diagnostic Trouble Code = Circuit shorted to voltage between PCM and fuel gauge sending unit.

Hex Code = 97
Generic Scan Tool Code = P0460
DRB Scan Tool Display = Fuel Level Unit No Change Over Miles
Description of Diagnostic Trouble Code = No movement of fuel level sender detected.

for additional information on troubleshooting and resolution:
http://rapidshare.com/files/138412864/ServiceManual.Jeep.Grand.Cherokee.1998_by_Parasico.rar

Mar 01, 2010 | 1998 Jeep Grand Cherokee

1 Answer

I have a 2005 Jeep Cherokee Laredo. Diagnostic


Implausible Fuel Volume Signal Received

This usually points to a bad PCM (powertrain control module).

Sep 14, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Jeep Grand Cherokee Limited P0700 diagnostic problem


P0700 means there is a transmission fault code in the transmission controller. Since the transmission controller doesn't have a light attached, it tells the engine controller to turn the light on using this code. You'll have to access the transmission controller to further diagnose the problem.

Jun 14, 2009 | 1998 Jeep Cherokee

2 Answers

Diagnostics "P1762 Manufac. Contrl. Transmission"


Had the same code on my 2002 Jeep Grand Cherokee. Started having shifting problems as well. Code is for governor pressure sensor on trans. Cost me about $800 for dealer to fix. No problems after part changed out.

May 22, 2009 | 2002 Jeep Grand Cherokee

1 Answer

How to clear the diagnostic codes on my 1993 jeep cherokee?


To clear codes on these, you can disconnect the battery, then re-connect. The only code remaining will be one indicating battery power was interuppted. This will not work on 98 and newer vehicles.

Feb 08, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Engine code 95 jeep grand cherokee lerado


12 is a battery disconnect within the last 50 start cycles and 55 means the end of the diagnostic cycle.  Basically the computer found nothing wrong. The 12 code may seem incorrect if you haven't disconnected the battery recently, but from my experience the 12 code shows up almost all the time regardless.

Dec 16, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
2003 Jeep Grand Cherokee Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...