Question about 2003 Kia Sorento
Where is the location of the radio fuse? need to change the aerial
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: to remove radio
THE FACIA HAS TO BE REMOVED TO ACCESS THE RADIO SCREWS THIS IS NOT FOR THE FAINT HEARTED AS YOU HAVE TO BE BRUTAL PULLING THE SURROUND WITH OUT BREAKING THE FACIA SOLUTION IS LET A DEALER TAKE THE RISK OF BREAKING IT IF YOU WANT TO HAVE A GO REMOVE THE ASH TRAY AND START PULLING BUT I WOULD ADVISE AGAINST IT
Posted on May 08, 2009
SOURCE: remove factory radio
This is one that you can stare at all day. the trim pieces that include the air vents (usually woodgrain) will come off and expose the screws that hold the radio in. They are held in by spring clips, a gentle pry will get you started. Here is a website that shows how to remove one for a cell phone mount: http://www.bracketron.com/main/xmain_landing_page.php You may have to take the climate controll screws out to get the radio out far enough to reach the plugs on the back. You should be able to figure out the rest. good luck, and be gentle.. the trim is getting cheaper and cheaper, and is really easy to break.
Posted on May 15, 2008
The above information about the sensor being located at the top of the motor to the passenger side of center is bogus. That is only the pig tail plug in. The actual sensor pig tail continues down below, underneath the plastic lower timing belt cover, on the front of the motor, just above the crankshaft timing gear.
It is a very involved process of removing and replacing. You will have to remove all of the belts, the front timing belt covers, (upper and lower). You will also have to remove the front bracket that is mounted to the front of the block, which serves as the mount for the power steering pump, the alternator and the A/C compressor.You will also have to remove the crankshaft pulley. You cannot remove the plastic lower timing belt cover unless you remove all of these things first. The sensor is located underneath the lower cover. It has two bolts that hold it in place. You will have to remove these two bolts.
The crankshaft pulling bolt is a right handed thread and loosens by turning counter clockwise. The pulley will slip off but is a very tight fit. Do not try to turn it while removing it as there is a small pin that keeps it aligned to one position. Use a small ball pine hammer to tap it loose.
It is also a good idea to remove the electric cooling fan shroud that is mounted to the inside side of the radiator and the radiator hoses to give yourself more room to work. It has only two bolts at the top holding it in place. And then slips into two retaining clips at the bottom. Lifting it will pull it out of these retaining clips.
When you remove the small bypass hose located at the top of the radiator , to the passenger side, be careful not to break off the small nipple protruding out of the radiator tank. It is plastic and will break easily if you try to pull the rubber bypass hose from it. This will have to be taken to a radiator shop to have repaired if you accidentally break this off. Be sure to carefully loosen the hose from this nipple before trying to pull it off.
And one more thing, if you go to that much trouble to replace this sensor, it is a good idea to go ahead and replace the timing belt as well. It is a maintenance item and you will have to go through the same process to replace it as well. Do it once and do it all.
I hope this helps.
Posted on Nov 15, 2008
The diode for the interior dome light is located behind the driver's side kick panel. You have to remove the kick panel or get access to the wires behind the panel. The diode is located in the wrapped wires just to the left of the fuse box area. When you feel around the wrapped wires with your fingers, you will feel a small hard rectangular plastic piece behind the tape wrapping the wires. Carefully cut the tape at the spot and locate the diode. Remove the diode and replace with a new one (about $13-18 at Kia dealer) and test. Retape with electrical tape and replace kick panel and you are done. About a 15 minute job.
Posted on Feb 13, 2009
Be careful there.. If you remove the Throttle Position Sensor TPS or the throttle Cable, the engine light will come on because there is a certain setting that needs to be done to ensure accurate emission control.
Posted on Apr 14, 2009
Tips for a great answer:
Dec 27, 2015 | Kia Cars & Trucks
Mar 27, 2015 | 2007 Kia Sorento
Feb 05, 2015 | Kia Cars & Trucks
Aug 26, 2013 | Kia Cars & Trucks
Oct 06, 2012 | 2003 Kia Sorento
Jun 12, 2012 | 2005 Kia Sorento
Jul 14, 2011 | 2006 Kia Sorento
Feb 04, 2011 | 2003 Kia Sorento
Feb 14, 2010 | 2003 Kia Sorento
69 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: