Question about Cars & Trucks

1 Answer

Fix Yahow toreplacecombinationswitch on grand cherrekeejeep 200 4.7l

How to replace combination switch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,209 Answers

First off, let us start with a little thing on your keyboard known as a space bar. You should just have to remove the upper and lower plastic trim from the steering column to get access to the multifunction switch. Then it should just be a couple of bolts or screws and a couple of plug ins to remove the old one and then replace the new one in the same, but reverse order.

Posted on Apr 23, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change a sunroof switch on a 98 grand prix gtp?


just look like a pull away and down type part

dome light and sun roof switch combined

buy the replacement switch
before you break the original getting it out



mi0bxgdpypadyhyaru0u2jq-gvbdhzrta0vksrs4gnzywznx-2-0.jpg

Mar 26, 2017 | Cars & Trucks

2 Answers

D2006 grand prix, windshield wipers fail to work occationally, replace motor issue still happens, to fix keep turning wipers on and off until they start again. any ideas what issue is?


I have seen 2 options on the grand prix. First check ground strap by wiper motor............[under cowl cover]. Second would be your combination switch on steering column. ie turn signal. headlamp high low etc.

Mar 25, 2015 | 2006 Pontiac Grand Prix

2 Answers

I have a 1995 grand prix Blinkers dont work but, other lights do.


First check turn signal fuse and relay if, they are good then try pressing on and off the hazard switch while turning the signal switch on.If signals start to work replace hazard switch.If hazard switch is good then replace turn signal switch.

May 02, 2011 | 1995 Pontiac Grand Prix

1 Answer

Headlights, dome, and dashlights are out on my 97 grand marquis . Do I need to look at the fuse box or the power distribution box for my problem?


For the head light power distribution box not only is it fused its a circuit breaker fuse that means it quickly restore the short then light up get a short then light up, that a circuit breaker. what you really need to look for is a switch that failed. Here is how it works some model have a switch and a combination switch. or just a combination switch. if you have a switch and a combination switch here is how it works power reside in the switch then travels to the combination then to the headlamps. then there is combination it self. power reside in the juction box and the switch just sullpies the signal to the relay that turns on the headlamp. did i confuse you? then take a easy route inspect for open fuses in the juction box, might as well do the fuse box. if it looks good replace the comination

Apr 29, 2011 | Mercury Grand Marquis Cars & Trucks

1 Answer

My left blinker quit working. I know the bulb doesn't need to be changed. I think it's in the combination switch. How do I fix it?


check the feed in and the feed out of the switch as it could be something else like a cable or multiplug faulty

Dec 29, 2010 | 2000 Jeep Grand Cherokee

2 Answers

1998 dodge grand caravan turnnig lights don't work. How do i change multifunction switch and where is it? Mac


Hi hope this helps you out.
printpage_icon.gif


REMOVAL & INSTALLATION

See Figure 1


0900c1528003c797.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: The turn signal (multi-function) switch is attached to the steering column by two screws

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR system wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the upper and lower steering column shrouds.
  4. Disconnect the electrical connector from behind the combination switch.
  5. Remove the mounting screws securing the combination switch to the steering column adapter collar.
  6. Remove the combination switch from the vehicle.

To install:
  1. Install the combination switch to the steering column adapter collar. Tighten the combination switch mounting screws.
  2. Reconnect the electrical connector to the combination switch.
  3. Install the upper and lower steering column shrouds and tighten the retaining screws.
Reconnect the negative battery cable and check all functions of the combination switch for proper operation.
Let me know if theres anything else I can help with. Thank You for using fixya.........iluv2fish........Ray.......

Jul 23, 2010 | 1998 Dodge Grand Caravan

1 Answer

I need instructions on replacing a turn signal switch. Our current turn signal is no longer returning or cancelling.


For Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004 check this guide for change Turn Signal Switch:
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the air bag or SIR system wiring. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disconnect and isolate the negative battery cable from the battery.
  2. In order to disarm the air bag system, allow the system capacitor to discharge for at least 2 minutes, before performing any removal procedures.
  3. Remove the upper and lower steering column shrouds.
  4. Disconnect the electrical connector from behind the combination switch.
  5. Remove the mounting screws securing the combination switch to the steering column adapter collar.
  6. Remove the combination switch from the vehicle.

    7e690ec.jpg
    Fig. The turn signal (multi-function) switch is attached to the steering column by two screws

To install:
  1. Install the combination switch to the steering column adapter collar. Tighten the combination switch mounting screws.
  2. Reconnect the electrical connector to the combination switch.
  3. Install the upper and lower steering column shrouds and tighten the retaining screws.
  4. Reconnect the negative battery cable and check all functions of the combination switch for proper operation.

Hope helps (remember rated this).

Jul 01, 2010 | 2002 Dodge Grand Caravan

3 Answers

Headlights


disconnect the module that is mounted in front of the fuse box .Then carefully clean the the connectors ,they are usually pretty dirty.After they are clean put it back 2gether.If it doesnt solve the prob then u might have to stick some washers on your bottom screws so that your module is angled in.This will ensure a solid connection.

Oct 19, 2009 | 2001 Dodge Grand Caravan

1 Answer

Replace multifunction switch on Pontiac Gran Prix 2000


no just the top and bottom of the steering wheel cover

Dec 07, 2008 | 2000 Pontiac Grand Prix

2 Answers

Continous clicking (signal lights)


HI.there is a defective part called the hazard lamp switch located in the middle of the dash.These switches fail internally.Try poking the switch hard with your fingers a few times when you hear the noise.If the noise goes away,the switch is probably faulty.The switch is very easy to replace.Just remove the trim on the dash carefully,then remove the switch.

Sep 28, 2008 | 2003 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...