Question about BMW Cars & Trucks

Open Question

Abs fault codes64 - BMW Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS p1143 P1144 ABS CODE FAULT ?


1143 is Air Assist Control Valve Range/Performance

1144 is Air Assist Control Valve Circuit Malfunction
Check the codes again after resetting the fault memory.

Feb 27, 2018 | Ford Cars & Trucks

1 Answer

What causes ABS light to stay on continuously


You will need to get the fault codes read as the fault can be any of the following
abs sensor fault
wiring fault to any of the sensors
abs ring lost teeth or read fault
abs controller self test fault
abs pump fault
brake line not holding pressure slight leak

Feb 01, 2017 | Cars & Trucks

1 Answer

I got a Lincoln navigator 2004 my abs ight and avtra light How turn it off


The ABS warning light is on because the control module for the ABS has sensed a fault, until the fault is repaired the light will remain on and you have no ABS brakes. You need the ABS system scanned for the fault code to see what part or wiring is defective. When the system is repaired the light will go out.

Jan 27, 2017 | 2004 Lincoln Navigator

1 Answer

How too take abs light off after new brakes are fitted


Fitting new brakes wouldn't usually put the abs light on unless you disconnected the abs and then switched on the ignition, made an unfortunate mistake or coincidentally an abs fault occured naturally.

The abs light is supposed to illuminate for a few seconds when the ignition is switched on and then go out signalling there are no faults. If the abs light is on it means a fault has been detected.

Early systems would cancel the light when the fault had been located and rectified but I believe modern systems require the use of diagnostic equipment.

Jun 12, 2016 | Cars & Trucks

1 Answer

Abs replaced axle shaft @ abs cable abs light still on after reset


The ABS fault light will stay on until the problem is repaired, read the fault code and diagnose it again.

May 14, 2016 | 2003 Mazda Protege

1 Answer

Abs light on a 06 expedition


Having the vehicle checked for DTC'S - diagnostic trouble code's would be a good first step . ABS light on codes are stored . Suggest you take your vehicle to a qualified repair shop that has the knowledge an testing equipment to diagnose the problem properly .
Anti-Lock Brake System (ABS)
The 4-wheel, 4-channel anti-lock brake system (ABS) consists of the following components:
  • ABS module
  • Front wheel speed sensor
  • Front wheel speed sensor ring (integral to the front wheel bearing)
  • Hydraulic control unit (HCU)
  • Rear wheel speed sensor
  • Rear wheel speed sensor ring (integral to the rear halfshaft)
  • Yellow ABS warning indicator
  • As you can see here , it can set numerous
  • DTC'S Why guess an replace parts that won't fix the problem .
  • Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU is Faulted ABS Module NOTE: If other DTCs are present, REPAIR them before installing a new component.
    CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved, INSTALL a new module. REFER to Anti-Lock Brake System (ABS) Module in this section. REPEAT the self-test. B1483 Brake Pedal Input Circuit Failure ABS Module Go To Pinpoint Test B . B1676 Battery Pack Voltage Out of Range ABS Module Go To Pinpoint Test C . B2477 Module Configuration Failure ABS Module CONFIGURE the ABS module. REFER to Section 418-01 . CLEAR the DTCs. REPEAT the self-test. If DTC B2477 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . REPEAT the self-test. B2734 Pedal Travel Sensor Supply Error ABS Module Go To Pinpoint Test M . B2736 Pedal Travel Sensor Circuit Fault ABS Module Go To Pinpoint Test M . B2737 Pedal Travel Sensor Jammed Error ABS Module Go To Pinpoint Test M . B2738 Pedal Travel Sensor Velocity Error ABS Module Go To Pinpoint Test M . B2740 Pedal Travel Sensor Spike Error ABS Module Go To Pinpoint Test M . B2741 Sensor Cluster Defective ABS Module FOLLOW the diagnostic tool directions for the calibration procedure. B2900 VIN Mismatch ABS Module VERIFY that the module has the correct as-built data.
    CHECK for correct powertrain control module (PCM) and ABS module configurations using the diagnostic tool. RECONFIGURE the component as necessary. FOLLOW the diagnostic tool directions for the ABS module configuration or REFER to Section 418-01 for the PCM. CLEAR the DTC. REPEAT the self-test. C1095 ABS Hydraulic Pump Motor Circuit Failure ABS Module Go To Pinpoint Test D . C1145 Speed Wheel Sensor RF Input Circuit Failure ABS Module Go To Pinpoint Test E . C1155 Speed Wheel Sensor LF Input Circuit Failure ABS Module Go To Pinpoint Test E . C1165 Speed Wheel Sensor RR Input Circuit Failure ABS Module Go To Pinpoint Test E . C1175 Speed Wheel Sensor LR Input Circuit Failure ABS Module Go To Pinpoint Test E . C1233 Speed Wheel LF Input Signal Missing ABS Module Go To Pinpoint Test F . C1234 Speed Wheel RF Input Signal Missing ABS Module Go To Pinpoint Test F . C1235 Speed Wheel RR Input Signal Missing ABS Module Go To Pinpoint Test F . C1236 Speed Wheel LR Input Signal Missing ABS Module Go To Pinpoint Test F . C1277 Steering Wheel Angle 1 and 2 Circuit Failure ABS Module Go To Pinpoint Test G . C1278 Steering Wheel Angle 1 and 2 Signal Faulted ABS Module Go To Pinpoint Test G . C1279 Yaw Rate Sensor Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1280 Yaw Rate Sensor Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1281 Lateral Accelerometer Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1282 Lateral Accelerometer Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1285 Booster Solenoid Circuit Failure ABS Module Go To Pinpoint Test I . C1287 Booster Pedal Force Switch Circuit Failure ABS Module Go To Pinpoint Test J . C1288 Pressure Sensor Main/Primary Input Circuit Failure ABS Module Go To Pinpoint Test K . C1440 (with stability assist) Pressure Sensor Main/Primary Signal Faulted ABS Module Go To Pinpoint Test K . C1516 Roll Rate Sensor Signal Fault (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1517 Roll Rate Sensor Circuit Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C1730 Reference Voltage Out of Range (+5V) ABS Module Go To Pinpoint Test L . C1805 Mismatched PCM and/or ABS-TC Module ABS Module CHECK for correct PCM and ABS module configuration using the diagnostic tool. RECONFIGURE the component as necessary. FOLLOW the diagnostic tool directions for the ABS module configuration or REFER to Section 303-01 for the PCM. CLEAR the DTC. REPEAT the self-test. C1963 Stability Control Inhibit Warning ABS Module This DTC is for information only. GO to the Principles of Operation. CLEAR the DTC. REPEAT the self-test. C1991 Module Calibration Failure ABS Module Follow the diagnostic tool directions for the calibration procedure. C1996 Active Yaw and/or Roll Control Disabled ABS Module This DTC can be set if the ABS module system is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment or other items that can alter the vehicle tracking dynamics. CLEAR the DTC. REPEAT the self-test. C1998 Module Calibration Not Complete ABS Module Go To Pinpoint Test O . C2769 (ABS only) Longitudinal Acceleration Sensor Electrical Failure ABS Module INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. CLEAR the DTCs. REPEAT the self-test. C2769 (ABS with stability assist) Longitudinal Acceleration Sensor Electrical Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2770 (ABS only) Longitudinal Acceleration Sensor Plausibility Failure ABS Module INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. CLEAR the DTCs. REPEAT the self-test. C2770 (ABS with stability assist) Longitudinal Acceleration Sensor Plausibility Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2777 Sensor Cluster Bus Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . C2778 Sensor Cluster Power Supply Failure (Sensor Cluster Fault) ABS Module Go To Pinpoint Test H . U1900 CAN Communication Bus Fault-Receive Error Network Fault REFER to Section 418-00 . U1901 CAN Network #2 Communication Bus Fault-Receive Error Network Fault Go To Pinpoint Test H . U2023 Fault Received from External Node Instrument Cluster REFER to Section 418-00 .

Oct 22, 2017 | 2000 Ford Expedition

1 Answer

Fiesta duratec 2005 Abs warning light on


Whenever the ABS module turns on the ABS light in the dash it is to alert you to the fact that a fault has occurred in the ABS system and the control module has turned off the ABS brake control, you now have regular non ABS brakes. The waring light will stay on until the fault is corrected. Since a large number of problems would cause this you must get the control module scanned to retrieve the fault code that was set in the control modules memory when it turned on the light. Once the fault code is known the process of diagnosis and repair can begin.

Feb 10, 2012 | 2005 Ford Fiesta 1.6

1 Answer

ABS FAULT WITH NISSAN TERRANO YREG


Had same fault - was damaged wiring in loom at back of engine where main engine harness meets the bulkhead.

There is a screened cable grey/pink that houses the two O/S/F ABS wires blue and pink. The loom copex cuts through the ABS cable causing this fault. Take a look at link below:

http://www.bba-reman.com/forums/Topic79424-1-1.aspx

Jun 12, 2009 | 1997 Nissan Pathfinder

1 Answer

Mazda tribute abs fault. abs light comes on & of when starting all ok. does not come on when driving, but you can feel the abs coming on when it shouldn't, intermittent. no fault codes, no abs light on...


These vehicles have a recall on the ABS system for faulty wiring. You may want to check with your local dealer to see if your vehicle is included.

Sep 16, 2008 | 2003 Mazda Tribute

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Chris Bowser

Level 1 Expert

18 Answers

Nyte_Ryder

Level 2 Expert

102 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...