Question about Cars & Trucks

1 Answer

Yesterday I paid for this but still have not heard from you. Why do you make it so hard to contact, afraid>>>Jack E Welch955 Mountain Pass, Va 24064540 597

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.

  • Cars & Trucks Master
  • 102,366 Answers

You couldn't have paid FixYa since FixYa is a free service. Please contact the vendor whom you paid.
If you find it hard to contact them, imagine how hard it is for us when we don't even know the name of the company or what you bought from them.

Posted on Apr 22, 2013

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2001 Chevy venture will not start. We had an inspection done yesterday, oil change & a power steering line replaced As well. Looks like they had moved the wiring harness & also taped it when this...

-Battery is full...? If so check for corosion battery cable.
And make sure good connector (Tight)
-If all are good and just Click but can't turn. >>> Need new starter.


Apr 02, 2013 | Cars & Trucks

1 Answer

I own a 1996 pontiac gr am gt. It is not blowing cold air. don't think it needs freon. Think it's either the compressor or the small part that connects to the compressor. My question is, where is...

Hi! cw43248
Realy need gauges to check pressure on system. There is a multitude of explanations and would realy need to know the pressure of the system. Pressure needs to be high enough to activate low pressure switch. Of course if the compressor is unpluged, a relay is bad, both fans are not running, or any of the fuses are open this is just the beginning of the diognosis.
Hope some of this helps.

Jun 25, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

I paid $12.00 for a problem solution ,yesterday and I have not receive any answer,im really dissapointed of cotacting FIXYA

If you scroll down to the bottom of the page you can select "contact". You can send a message explaining what happened. See if you get an answer there. Otherwise contact your credit card company.

Apr 17, 2011 | Toyota Previa Cars & Trucks

1 Answer

What tools do i need to remove a 1996 lexus es 300 cv axle from the transmission

You will need a lug wrench for the wheel, a jack, a jack stand, 14mm socket and ratchet for disconnecting the lower ball joint, a 32mm socket and impact wrench for the axle nut, a dead-blow (no-bounce) hammer to tap axle from steering knuckle, and then there are two options.

Left (driver) side: a pry bar to pop the axle from the differential (pry between diff. housing and axle knuckle. This can be really stuck so don't be afraid to put some power to it!)

Right (pass.) side: snap ring pliers to remove snap ring from carrier mount (rear engine mount houses this carrier bearing), and i think a 14mm socket or wrench to loosen the jam bolt that keeps the bearing outer race from spinning.

Good luck and be safe!!


Feb 12, 2011 | 1996 Lexus ES 300

2 Answers

Today I test drove a 2003 Ford Thunderbird with 56k miles that I'm considering buying. While driving at low speeds I heard a rolling thumping noise coming from the rear of the car. Couldn't tell it it was...

Sounds like a wheel bearing get in ready to go out Jack up each side put on jack stands grab wheel pull & push it see if there's any play if so thats your problem

Jan 04, 2011 | 2003 Ford Thunderbird

2 Answers

Changing rear (3) spark plugs

carefully remove the coil pack with a deep 10mm socket and unplug the 2 connections on the pass side of the coil and just lean it over to the driver side of the car and you will have access to the rear of firewall.

Jun 05, 2009 | 2003 Chevrolet Impala

1 Answer

I received a electric car jack from Heartland of America and had to send it back to them because the plug didn´t work for my 2008'Toyota Highlander and the 1999 Ford Taurus. they replaced the jack and...

> I contacted you (?) by phone and was assured that you (?)would send me another unit within 3-days.

I don't think you contacted anyone on this site.
I'm afraid Fixya is not going to be much help; your problem is with Heartland.
I have dealt with them often over the years and have not personally had a problem with them.

Sep 03, 2008 | Toyota Highlander Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides