Question about Cars & Trucks

1 Answer

Map sensor for gmc jimmy 1997 - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

Its a small black box, should be on top of the intake near the center or rear towards the windshield.

Posted on Apr 22, 2013

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 231 Answers

SOURCE: 1997 GMC Jimmy Crank Angle Sensor

it's at the front of the engine and below the and left of the front of the crank shaft.
dis-connect negative attery cable
dis-connect the electical connector to the sensor
un-bolt it and pull it out
reversr for installation

Posted on Oct 10, 2008

  • 740 Answers

SOURCE: set timing 1997 jimmy

Ok that's pretty simple Put cylinder # 1 on TDC= top dead center on the (compressionstroke piston all the way up). Mark on metal part of distributor (with marker) where the number one is on the cap( that's where the number 1 wire plugs in) Then in-plant distributor make sure that rotor point is pointed to #1 on the cap, turn distributor shaft until this is achieved or as close as possible try to center shaft so you can adjust... ****** or advance to fine tune after you in-plant distributor if needed. Contact if you need more help . Good Luck

Posted on Jan 06, 2009

  • 180 Answers

SOURCE: where is my 1 2 shift sensor 2000 gmc jimmy

Inside trans. pan at the rear of the valve body. They have a wire clip which holds them in.

Posted on Jan 21, 2009

  • 3 Answers

SOURCE: 1997 gmc jimmy

Sounds like the cpi injector assembly. The fuel pressure regulator may be leaking. Or the poppet valves on the injectors may be sticking or shot. I replaced almost every part on my truck and that is what it ended up being the whole time. It's a common problem on these models. Hope this helped

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When accelerate my 1999 gmc jimmy pops


Multiple failures will contribute to this symptom. Both mechanical and electrical issues need to be looked at. Check for "Engine light" and any active or stored engine codes. Running a cylinder compression test, fuel line pressure test, exhaust pressure test, check the timing, check for misfire, check for clogged fuel and air filter, defective MAF or MAP sensor, check for vacuum leaks. The more details you can provide. I may be able to help you more.

Feb 24, 2014 | 1997 GMC Jimmy

1 Answer

How can i bypass the o2 sensor 0n a 1997 gmc jimmy


You cannot do that because the sensor has a varied voltage output and the ECM will see it as something wrong.

Feb 21, 2013 | 1997 GMC Jimmy

1 Answer

Where is the evap purge solenoid sensor on a 1997 jimmy


where is the evap sensor on a 1997 gmc jimmy 4x4 6 cylinder

Jul 25, 2012 | 1997 GMC Jimmy

1 Answer

Need 95 gmc jimmy vacuum diagram. I have a loose


THat goes to your map sensor. If you look very closely under your hood there will be a vac line diagram there

May 09, 2010 | 1995 GMC Jimmy

1 Answer

1997 jimmy will start but dies 10 deconds later


check fuses for power if no power to some of them check for a bad fuse link wire on the starter.also does the key have a chip in it?

Jan 02, 2010 | 1997 GMC Jimmy

1 Answer

1994 GMC Jimmy hard to start and runs rough when first started


i think if you checked the sparking plugs and map sensors then check your distributer its maybe not delivering the current nedded to perform the spark to some of the cylinders

May 30, 2009 | 1994 GMC Jimmy

1 Answer

1997 gmc jimmy


Sounds like the cpi injector assembly. The fuel pressure regulator may be leaking. Or the poppet valves on the injectors may be sticking or shot. I replaced almost every part on my truck and that is what it ended up being the whole time. It's a common problem on these models. Hope this helped

Mar 01, 2009 | 1997 GMC Jimmy

1 Answer

1997 GMC Jimmy Crank Angle Sensor


it's at the front of the engine and below the and left of the front of the crank shaft.
dis-connect negative attery cable
dis-connect the electical connector to the sensor
un-bolt it and pull it out
reversr for installation

Oct 03, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...