Question about Cars & Trucks

Open Question

John deere 4720

Occasionally blows 30 amp fuse and dies when I hit a bump. Put a new fuse in and fires right up.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: 1996 Jeep Cherokee Died

Likely you got lots of water in the alternator. find a way to dry it out (compressed air usually works). Then try again. Water can damage alt permanently so you may need to have it tested (on a machine, out of car). Make sure you dry everything else as well water in any system can really mess things up!!!

Posted on Mar 09, 2009

mikehitchner
  • 28 Answers

SOURCE: 30 amp ignition fuse in engine compartment blows at start

It sounds like a bad ignition switch or something is grounding out.Try to isolate the problem to key positions.See if the fuse blows when you turn the key to ACC(when your dash lights come on without starting)If the fuse does not blow then when you go to start it and it blows it could be one of many problems,the more common ones could be ignition switch,wiring,starter relay,starter soleniod,or perhaps the starter itself is shorting out,this can sometimes happen when a starter goes bad.

Posted on Apr 12, 2009

  • 6982 Answers

SOURCE: Fuel ECU fuse keeps blowing (30 amp)

Your fuel pump is internally binding and causing the fuse to blow. Change the pump (and filter while you're back there.)

Posted on Jun 14, 2009

gypsycat00
  • 224 Answers

SOURCE: 99 dodge neon # 10 fuse ing feed 15 amp blows out

There's a short in the circut. Check continuity of the wires that feed from that fuse (you'll need a wiring diagram to identify each wire). You've got something that is causing too much amperage to move through the circut and the fuse blows. Make sure the amperage on the fuse is correct for the application (your owner's manual or fuse box diagram should tell you what amperage rating to install in each fuse slot).

Posted on Jul 03, 2009

  • 1244 Answers

SOURCE: EFI 15 amp fuse keeps blowing, any suggestions?

you either got a shorted wire to the injectors or a injector stuck! or shorted

Posted on Jan 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine runs for about 30 seconds and shutdown like an electrical shutdown as opposed to a fuel related shutdown.


Engine fired up, ran normally for 30 seconds, then shut down ...

www.thedieselstop.com > ... > 7.3L IDI Diesels (Not Power Strokes)
Sep 25, 2012 - Engine fired up, ran normally for 30 seconds, then shut down. ... it fired up and has been running since... if it just ran out of fuel jump it, and keep ...

Viewing a thread - cummins m11 starts then dies - AgTalk Home

talk.newagtalk.com/forums/thread-view.asp?tid=332921...flat...1

Sep 24, 2012 - 9 posts - ‎9 authors
98 KW with a cummins m11 will start and run for 5 seconds then dies. ... anything else like that, because it would run for 30 seconds and then die, not 5. ... The engineprotection system will not shut down the engine unless the ...

[PDF]John Deere Engine Safety Shutdown with "Black Box" (prior ...

www.tuckerbilt.com/.../John%20Deere%20Engine%20Safety%20Shutdo...
John Deere Engine Safety Shutdown with "Black Box" (prior to Tier II ECU ... Ifengine fails to start in 30 seconds, the Low Oil ... Test #1 (Engine not running).

1800 RPM for 30 sec before shut down [Archive] - Pilots of America ...

www.pilotsofamerica.com > ... > Pilot's Lounge > Technical Corner

Jan 01, 2016 | Cars & Trucks

1 Answer

When I turn on my heat or air, nothing happens. There is a slight hint of heat or AC coming out of the vents when I have it set at 4. It will occasionally work, if I hit a bump just right, and it kicks...


If I'm reading this correctly- your blower isnt working? the fan doesn't blow? If the blower comes on over hard bumps, probably the blower motor is bad. More common is blower resistor, but try to find motor & bang on it while switched on...if it comes on, the motor is bad.

Sep 15, 2013 | 2004 Dodge Stratus

2 Answers

Getting no fire doesnt crank over


If the engine died when you hit the bump then the battery shorted against the frame and prob. blew the slow blow wire fuse. This located on the firewall under the hood about in the middle of the windshield. You will what looks like wires with eyelets connected to a whitish ceramic block mounted to the firewall. you will have to use a test light and see if it blown. Again it looks lust like a plain wire and wont show ant sighn of being bad you must test it. Its real name is " fuseable link" It could be red pink or sometimes yellow in color.

Jan 06, 2013 | 1971 Chevrolet Monte Carlo

1 Answer

When i get in my 2002 bonneville and turn the heat or the AC on nothing blows out, but from time to time if i hit a bump in the road while im driving sometimes it will starting blowing out. What is the...


There is a bad connection somewhere in the circuit. Could be the motor, the fuse/fuse box, the switch or a break in the wire that makes occasional contact.

Feb 11, 2011 | Pontiac Bonneville Cars & Trucks

1 Answer

Trouble starting doesnt seem to want to fire


Check the fuses, I had one a while ago that kept blowing one of the ECM fuses. There are 2 ECM fuses one also sends power to the fuel pump too. Do you hear the fuel pump run when you turn the ignition switch to on? Just turn the key to the "on" position, not all the way to start, you should be able to hear the fuel pump run for about 3-5 seconds. I think it takes a 15 amp, I showed the owner which fuse it was and it would blow occasionally. One day it blew one right after another so he put a 30 amp in, he was out of 15's. I told him that was not a good idea. Anyway, that fixed it he drove it home and put a 15 amp fuse back in it, it's been good ever since.

Nov 30, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Don't know what fuse is what .10 amp blows right


try different fuses starting with lowest then go up but think it is a 30 amp fuse ?

Oct 08, 2009 | 2001 Jaguar XJ8

1 Answer

My pickup is blowing the EFI fuse every time you hit a bump.


i had the same problem on time i had a o2 sensor melted to exhaust behind cab and fuel pump wires were loose i fixed the wires and put in new fuse and started right up

Aug 30, 2009 | 1993 Toyota Pickup

1 Answer

Car blows starter fuse after hitting bump in road causing car to die. Changed 30amp fuse and tried to start and blows fuse agian


check out the wiring. The bump may have made some connections loos or may have shaken up the wires and wires that are exposed may have hit each other or the metal part of the car which caused a short and in turn caused a fuse to blow.

Jun 25, 2009 | 2004 Dodge Neon

2 Answers

1996 Jeep Cherokee Died


Likely you got lots of water in the alternator. find a way to dry it out (compressed air usually works). Then try again. Water can damage alt permanently so you may need to have it tested (on a machine, out of car). Make sure you dry everything else as well water in any system can really mess things up!!!

Mar 09, 2009 | 1997 Jeep Cherokee Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...