Question about Toyota Cars & Trucks

Open Question

Diagnostic testing My 2004 Toyota Hilux D4D has diagnostic socket under the bonnet. I have been told to flash diagnose by linking out TE1 and E1. TE1 has nothing connected to it and neither does TE2. Does anyone know how to flash diagnose on this model?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 20 Answers

SOURCE: 1979 Toyota Hilux alternator wiring

always, counterclockwise starting with blue, then yellow, then red

Posted on Apr 26, 2009

Ad
  • 245 Answers

SOURCE: No Spark 1992 toyota camry

you should also check the crank position sensor this is what tells the ecm when to spark. this is a prox switch and when unplugged and checking ohms while cranking you should see a sqaure wave. should go from 0 ohms to infinity. when these go out you will not get any spark on any cylinder

Posted on May 19, 2009

  • 277 Answers

SOURCE: Toyota diesel hilux D4D noisy engine.just

Take the Vehicle back to the Installer/Supplier, for a Free of Charge CHECK and ADVISE under New Engine Warranty. If the OIL PRESSURE is LOW, when starting up from COLD, there is a genuine fault, so do not drive any distance.
Regards,DT

Posted on Aug 28, 2009

  • 1 Answer

SOURCE: 93 toyota corolla check engine light on

i have a 93 toyota camry and going down the road just giving it a little gas it will shut down. it will run great setting their but get to go no more then 20 mph driving me crazy can afford to get a pro but i need to know how to do the check engine light obd two will not do it help going crazy

Posted on Sep 04, 2010

johnjohn2
  • 5763 Answers

SOURCE: Toyota hilux 3.0 D4D hard starting showing crankshaft position sensor circuit malfunction code P0335.how do i solve this...?

Check the connection to crank sensor, if wiring is good and connection is clean then replace the crank sensor and reset the code, this is the first step, the computer could be a problem also but most times its the crankshaft sensor. good day

Posted on Feb 22, 2012

Testimonial: "The connections to the sensor were bad and the hard starting is gone.Thanks JB"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tilting backseat


glove box book

Hilux D4d Manual - lux-roc.com

www.lux-roc.com/hilux/hilux-d4d-manual.pdfToyota hilux tiger d4d sport cruiser manual pdf ' pdf owner ... Dec 05, 2014 Download Link: Pdf Download Toyota Hilux 2005-2011 Auto Repair Service Manual, ...

Oct 10, 2016 | Cars & Trucks

1 Answer

I have a toyota camry 220sei it cranks bt doesnt start. When l push it,it starts. Bt when it starts the rev counter doesnt pass 2 and when it moves doesnt rev more than 2


On the diagnostic plug under the bonnet you can bridge out TE1 and E1 and read the fault code on the cluster if it gives any. Is it a 1993 to 1997 model.

Jun 16, 2016 | Toyota Camry Cars & Trucks

1 Answer

I have toyota corolla 98 its overdrive light blinking please help me


O/D light flashing indicates a fault in the transmission. Manuall diagnose by bridging terminals Te1 and e1 on the diagnostic socket. refer to repair manual on the code got.

Nov 04, 2013 | 1998 Toyota Corolla

1 Answer

Which two diagnostic plugs to i cross under the hood to get engine code to flash on dash


TE1 and E1. See here p296

http://www.turboninjas.com/camry/eg1.pdf

Mar 09, 2013 | 1994 Toyota Camry

1 Answer

How do you read a computer on an 1986 toyota pickup


Jumper the TE1 terminal to the E1 terminal in the diagnostic connector with the ignition switch on and the check engine light will flash the codes. I think the diagnostic test connector is under the hood on the drivers side near the strut support and air filter box. It has a hinged plastic top about 3/4" x 1-1/2" in size. the terminal labels are inside the cap.

Feb 19, 2013 | 1986 Toyota Pickup 4WD

2 Answers

How do i check a code on my 93 toyota pickup without a scaner


If you tell me which engine you have, I can also provide the code list.
1989-95 MODELSjturcotte_2396.gif

  1. Make sure the battery voltage is at least 11 volts.
  2. Make sure the throttle valve is fully closed.
  3. Place the gear shift lever in Neutral. Turn all accessories off.
  4. The engine should be at normal operating temperature.
  5. Using a jumper wire, connect terminals TE1 and E1 of the Data Link Connector 1 (DLC1).
  6. Turn the ignition switch ON , but do not start the engine. Read the diagnostic code by the counting the number of flashes of the malfunction indicator lamp.
  7. Codes will flash in numerical order. If no faults are stored, the lamp flashes continuously every 1 / 2 second. This is sometimes called the Normal or System Clear signal.
  8. After the diagnosis check, turn the ignition OFF and remove the jumper wire.
  9. Compare the codes found to the applicable diagnostic code chart. If necessary, refer to the individual component tests in this section. If the component tests are OK, test the wire harness and connectors for shorts, opens and poor connections.

Oct 13, 2011 | 1993 Toyota Pickup

1 Answer

1993 Toyota Camry Engine light comes on start panel


There is usually a diagnostic box when u raise the bonnet. It is located at the passenger side, close to the body of the vehicle. If u open it, u will notice that there r 2 points E1 & TE1. Bridge those two and observe how the engine light flashes, ie how often after pauses. The blink between pauses represents a digit. Remember it and tell me what number u ended up with

Nov 12, 2008 | 1993 Toyota Camry V6

2 Answers

1993 toyota camry turn check engine light off


Open the hood. Locate a small grey box by the firewall, roughly 1.5 x 1.5 inches. It has a cap that will lift up, but it will not come off. Under the cap, located the terminals E1 and Te1. Using a standard paper clip, "jump" E1 and Te1 together. Turn the key on. Obnserve the check engine light; it will flash, pause and flash again. Count the flashes.
Examples: 2 flashes/pause/4 flashes is code "24"
1 flash/pause/5 flashes is code "15"
Get the codes & get that info back to me so that I will be able to assist you with your issue further.

Oct 04, 2008 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...