Question about 1992 Acura Integra Hatchback

1 Answer

Car wont start

I removed my dash to fix the lh door hinge area after an accident. Car ran great before removal. I plugged in every electrical connection. When I try to start it I noticed the seat belts do not retract and all I get is a beeping alert. Everything lights up, blower motor works, battery is charged.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

It is quite possible that you have disturded an earth point and not reconnected it, my advise is to strip it all back down and have a close examination of the area

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

1 Answer

Need help putting an aftermarket stereo in a 2001 toyota camry the factory stereo an conector were cut out and are gonna I found a diogram but the car is missing the 2 wires to hook up the rite front?


Look at right front door hinge area to see if the wires show there and trace them under dash. If none at hinge, remove door panel and find them.

Mar 28, 2016 | Toyota Cars & Trucks

1 Answer

How do i take the entire drivers side door off of my 2011 HHR? Its a DIY project n cant afford what the insurance isnt covering. My car was T-boned and wont even open. Basically smashed shut.


You need to have the door forced open before you can access the hinges and remove it.
Remove the interior door trim and the door can be unbolted at the door hinge area. Examine the door on the undamaged passenger side before you do anything.

Nov 04, 2015 | Cars & Trucks

1 Answer

What step are taken to remove a dash from a 1996 lincon towncarto access the a/c heater blend door actuator


what is the issue? May not be the blend door motor. Big job.

The climate control assembly has three control knobs (18519):
  • The airflow control or function selector knob controls vacuum and electrical applications.
  • The temperature control knob, attached to the potentiometer, controls the position of the A/C electronic door actuator motor (19E616) mounted on heater air plenum chamber (18471).
  • The blower motor control knob, attached to the heater blower motor switch (18578), provides four speeds of blower motor operation.
------------------------------------------------------------------------------------
A/C Electronic Door Actuator Motor Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove instrument panel (04320). Refer to Section 01-12 .
Instrument Panel Removal
  1. Position wheels straight ahead.
  2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  3. Raise vehicle on hoist. Refer to Section 00-02 .
  4. Remove RF wheel and tire assembly. Refer to Section 04-04 .
  5. Remove retaining nut in radiator coolant recovery reservoir area.
  6. Remove bolt retaining front fender apron (16054) to front fender (16005).
  7. Position front fender splash shield out of the way.
  8. Lower vehicle.
  9. Tag and remove wiring connectors.
  10. Remove retaining screw in parking brake control (2780). Remove parking brake control.
  11. Remove screw retaining instrument panel steering column opening cover reinforcement (04502).









  12. Remove steering column assembly. Refer to Section 11-04 .
  13. Remove from the LH and RH cowl side trim panels (02345).
  14. Remove lower cowl side trim panels.
  15. Tag and disconnect wiring connectors in LH and RH cowls.
  16. Remove ground wire assembly.
  17. Remove retaining rivet in the passenger side of the instrument panel (04320).
  18. Unsnap the instrument panel finish panel (04338), center and RH.
  19. Unsnap the instrument panel finish panel, (LH).
  20. Remove and disconnect the radio chassis (18806).
  21. Remove retaining screw in the instrument panel finish panel.
  22. Position the instrument panel finish panel out of the way.
  23. Tag and disconnect the wiring connectors.
  24. Remove retaining screw in the passenger side air bag module (044A74).
  25. Disconnect the electrical connector to the passenger side air bag module.
  26. Remove and disconnect the instrument panel upper finish panel (044A90).
  27. Remove instrument panel to cowl brace retaining screw.
  28. On Crown Victoria, Grand Marquis, remove screws retaining instrument panel finish panel (044D70) and remove instrument panel finish panel.
  29. Remove retaining nut on the instrument LH and RH lower finish panel.
  30. Remove instrument panel cowl brace (045D56).
  31. Disconnect vacuum hose on the harness assembly.
  32. Remove upper and lower screws retaining instrument panel finish panel to dash panel (01610).


  1. Disconnect the A/C electronic door actuator motor electrical connector.
  2. Remove four A/C electronic door actuator motor retaining screws.
  3. Remove A/C electronic door actuator motor (19E616).

Jun 14, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

How do i remove instrument panel cluster on 98 towncar


Removal
  1. Remove the steering column
  1. Remove the passenger side air bag module
  1. Position the speed control servo aside.
    1. Remove the nuts.
    1. Position the speed control servo aside.
    gr2792a.gif
  1. Disconnect the LH bulkhead connector.
    1. Loosen the bolt.
    1. Disconnect the LH bulkhead connector.
    gr2793a.gif
  1. Unclip the LH bulkhead connector from the dash panel.
    gr2794a.gif
  1. Remove the windshield washer reservoir
  1. Disconnect the blower motor electrical connector.
    gr2795a.gif
  1. Disconnect the A/C pressure cut-off switch electrical connector.
    gr2796a.gif
  1. Disconnect the in-line wiring harness connector.
    gr2797a.gif
  1. Disconnect the electronic automatic temperature control (EATC) variable blower motor controller electrical connector.
    gr2798a.gif.
  1. Raise and support the vehicl
  1. Remove the RH front wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the RH front wheel and tire assembly.
    gr2845a.gif
  1. Remove the front fender splash shield bolts.
    gr2800a.gif
  1. Position the front fender splash shield away from the dash panel.
    gr2801a.gif
  1. Unclip the wiring harness from the evaporator case.
    gr2802a.gif
  1. Unclip the wiring harness from the dash panel.
    gr2803a.gif
  1. Lower the vehicle.
  1. Lower the RH instrument panel lower insulator.
    1. Remove the pushpins.
    1. Lower the RH instrument panel lower insulator.
    gr2805b.gif
  1. Remove the RH instrument panel lower insulator.
    1. Disconnect the power point electrical connector.
    1. Remove the courtesy lamp from the lamp socket.
    1. Remove the RH instrument panel lower insulator.
    gr2806a.gif
  1. Unseat the wiring grommet and feed the wiring harness through the dash panel.
    gr2804a.gif
  1. Remove the LH and RH cowl side trim panels.
    gr2807a.gif
  1. Remove the LH and RH windshield side garnish moldings.
    gr2808a.gif
  1. Disconnect the electronic crash sensor (ECS) module electrical connector.
    1. Disconnect the locking clip.
    1. Disconnect the electrical connector.
    dr0308a.gif
  1. Disconnect the antenna cable in-line connector.
    gr2809a.gif
  1. Remove the RH ground bolts.
    gr2810a.gif
  1. Disconnect the EATC hose from the evaporator housing.
    gr2811a.gif
  1. Disconnect the RH bulkhead connector.
    1. Loosen the bolt.
    1. Disconnect the RH bulkhead connector.
    gr2812a.gif
  1. Position the LH and RH door weatherstrip seals away from the instrument panel.
    gr2813a.gif
  1. Remove the tunnel brace trim cover.
    gr2814a.gif
  1. Disconnect the climate control head vacuum harness connector.
    gr2815a.gif
  1. Remove the instrument panel tunnel brace.
    1. Remove the nuts.
    1. Remove the instrument panel tunnel brace.
    gr2816b.gif
  1. Remove the LH ground bolts.
    gr2817a.gif
  1. Disconnect the LH wiring harness connectors.
    gr2818a.gif
  1. Disconnect the parking brake switch electrical connector.
    gr2819a.gif
  1. Remove the instrument panel defroster opening grille.
    1. Unclip the instrument panel defroster opening grille from the instrument panel.
    1. Disconnect the electrical connectors.
    1. Remove the instrument panel defroster opening grille.
    gr2820a.gif
  1. Remove the three instrument panel cowl top screws.
    gr2821a.gif
  1. Remove the RH instrument panel cowl side nut.
    gr2822a.gif
  1. Remove the upper LH instrument panel cowl side nut.
    gr2823a.gif
  1. Remove the lower LH instrument panel cowl side bolt.
    gr2824a.gif
  1. NOTE: Removing the instrument panel from the vehicle requires two technicians.
    Remove the instrument panel from the vehicle.
    gr2879a.gif

Mar 07, 2011 | 1998 Lincoln Town Car

1 Answer

Do i have to remove complete dash to replace a heater core in 1992 grand marquis.


Section 12-03: Air Conditioning System 1992 Town Car/Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Plenum Removal
  1. Disconnect battery ground cable.
  1. Disconnect the heater hoses from the heater core tubes. Plug the ends of the heater hoses to prevent coolant loss.
  1. Plug heater core tubes securely to prevent coolant leakage from heater core during plenum removal.
  1. Remove three nuts located below the windshield wiper motor retaining the LH end of the plenum to the dash panel (Fig. 15).


FIG. 15 Plenum and Air Inlet Duct Removal


ccl3438a.gif

  1. Remove one nut retaining the upper LH corner of the evaporator case to the dash panel.
  1. Remove LH and RH lower instrument panel insulators.
  1. Disconnect two vacuum supply hoses from vacuum source. Push grommet and vacuum supply hose into passenger compartment.
  1. Remove all instrument panel retaining screws and pull the instrument panel back as far as possible without disconnecting any wire harnesses.
  1. Loosen the RH door sill plate and remove the RH side cowl trim panel.
  1. On manual systems, disengage the temperature control cable housing from the bracket on top of the plenum. Disconnect the cable from the temperature blend door crank arm. On ATC systems, remove cross body brace and disconnect wiring harness from temperature blend door actuator and disconnect the ATC sensor tube from the evaporator case connector.
  1. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct.
  1. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  1. Remove two hush panels.
  1. Remove one plastic push fastener retaining the floor air distribution duct to the LH end of the plenum. Remove LH screw and loosen RH screw on the rear face of the plenum (Fig. 14), and remove the floor air distribution duct.
  1. Remove two nuts from the two studs along the lower flange of the plenum.
  1. Carefully move plenum rearward to allow heater core tubes and the stud at the top of the plenum to clear holes in the dash panel. Remove plenum from vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull lower edge of instrument panel rearward as necessary while rolling the plenum from behind the instrument panel.
Installation
  1. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  1. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  1. Install three nuts on the studs along the lower flange and one on the upper flange of the plenum (Fig. 15).
  1. Install three nuts below the windshield wiper motor to attach the LH end of the plenum to the dash panel.
  1. Install one nut to retain the upper LH corner of the evaporator case to the dash panel.
  1. Position floor air distribution duct on plenum. Install two screws and plastic push fastener.
  1. If removed, position panel door vacuum motor to the mounting bracket. Install two retaining screws.
  1. Connect the white vacuum hose to the outside-recirculating door vacuum motor.
  1. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install floor duct.
  1. Connect the ATC sensor tube to the evaporator case connector on ATC equipped vehicles.
  1. Install the cross body brace and connect wiring harness to the blend door actuator on ATC equipped vehicles.
  1. Connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable as outlined under Adjustments.
  1. Install the bolt to attach the lower RH end of the instrument panel to the side cowl.
  1. Install the RH side cowl trim panel and tighten the RH door sill plate retaining screws.
  1. Install glove compartment door and check arms.
  1. Connect vacuum supply hose to vacuum supply.
  1. Install RH and LH lower instrument panel insulators.
  1. Install two hush panels.
  1. Unplug the heater core tubes and connect the heater hoses to the heater core tubes.
  1. Fill the cooling system with coolant to replace coolant lost during removal of the plenum.
  1. Connect the battery ground cable. Check the system for proper operation.

Dec 17, 2010 | 1992 Mercury Grand Marquis

1 Answer

Locate lcm module 98 lincolin wont stay on


LCM is usually under dash above driver's feet.

They are $400. Gino on ebay fixes them a lot cheaper. Just search for lighting control module and you will find him.

SECTION 419-10: Multi-Function Electronic Control Modules 1998 Town Car Workshop Manual
REMOVAL AND INSTALLATION Module -Lighting Control (LCM) Removal
  1. swg~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of module, it is necessary to upload module configuration information to New Generation STAR (NGS) Tester. This information needs to be downloaded into the new module once installed.
    swg~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.
    Disconnect the battery ground cable.
  1. Remove the LH instrument panel lower insulator.
    1. Remove the pin-type retainers.
    1. Disconnect the courtesy lamp.
    1. Remove the LH instrument panel insulator.
  1. Position the LCM aside.
    1. Remove the screws.
    1. Release the locking tab.
    1. Position the LCM aside.

  1. Remove the LCM.
    1. Disconnect the electrical connectors.
    1. Remove the LCM.
Installation
  1. swg~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the new module is installed, it is necessary to download the module configuration information from New Generation STAR (NGS) Tester into the new module.
    NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns it adaptive strategy. The vehicle may need to be drive 16 km (10 miles) or more to relearn the strategy.
    To install, reverse the removal procedure.

888bfe5.gif

Oct 30, 2010 | 1998 Lincoln Town Car

1 Answer

Door sensors stuck. its always showing my car door is open. where is it located so I can unstuck it


When you open the door there is a little black plastic rod that comes out of the body of the car. It is usually where the door hinges hook to the body of the car close to the dash area. Youwillhave to remove and replace it.

May 05, 2010 | 2001 Ford Taurus

1 Answer

Replacing a front door hinge on a 1997 lincoln town car is it simple or is it labor intensive


It is labor intensive. I am in the process of doing one right now. First, the whole door must be removed and there's a lot of electrical in the drivers side front door. I ended up removing the door and pulling out the electrical harness (after disconnecting everything) enough that I could fold the door around and set it on the ground (on cardboard ). Then I attacked the Hinge. One bolt is easy to get to, the other is a ***** and it looks like the dash support may have to come out. Good luck.

Feb 03, 2010 | 1997 Lincoln Town Car

1 Answer

A/C evaporator overhaul on a Lincoln Continental 1999


SECTION 412-03: Air Conditioning 1999 Continental Workshop Manual REMOVAL AND INSTALLATION Evaporator Core Removal
NOTE: The evaporator core is serviced as a core and housing assembly. The evaporator core, internal doors, seals and door linkage are included with the housing. Transfer the blower motor and wheel assembly, heater core and cover, dash panel seals and vacuum actuators to the new housing.
  1. Remove the rear seat airflow duct (18C420). For additional information, refer to Section 412-01 .
  1. Remove the instrument panel (04320). For additional information, refer to Section 501-12 .
Instrument Panel Removal
sxe~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result.
  1. Remove the passenger side air bag module. For additional information, refer to Section 501-20B .
  1. If equipped, remove the floor console; refer to Console—Floor .
  1. If equipped, remove the mini console; refer to Console—Mini .
  1. If equipped, remove the rear seat climate control air duct sleeve.
  1. Remove the steering column; refer to Section 211-04 .
  1. Release the cable from the parking brake actuator.
    1. Release the cable from the parking brake actuator.
    1. Release the cable conduit from the parking brake actuator.
  1. Disconnect the LH outboard bulkhead electrical connector.
    1. Loosen the bolt.
    1. Disconnect the LH bulkhead electrical connector.
  1. Disconnect the LH inboard bulkhead electrical connector.
    1. Loosen the bolt.
    1. Disconnect the LH bulkhead electrical connector.
  1. If equipped, disconnect the heated seat switch electrical connectors.
  1. Remove the steering column mounting support to instrument cowl brace bolts.
  1. Remove the instrument panel dash brace to instrument panel bolt.
  1. Position the instrument panel dash brace aside.
    1. Loosen the nut.
    1. Position the instrument panel dash brace aside.
  1. Remove the RH instrument panel insulator (046A24).
    1. Remove the pin-type retainers.
    1. Remove the RH instrument panel insulator.
      • Remove the courtesy lamp.
  1. Disconnect the vacuum harness connector.
  1. Disconnect the in-line electrical harness connector.
  1. Position the RH scuff plate aside.
  1. Remove the RH cowl trim panel.
  1. Disconnect the antenna in-line connector.
  1. Remove the ignition/shifter interlock cable from the bracket and the shifter interlock cam.
  1. Remove the instrument panel defroster opening grille assembly.
    1. Lift upward to release the instrument panel defroster opening grille assembly from the instrument panel.
    1. Disconnect the two electrical connectors (one each side).
    1. Remove the instrument panel defroster opening grille assembly.
  1. Remove the instrument panel cowl top screws.
  1. Remove the RH instrument panel support to cowl side nut.
  1. Remove the LH instrument panel support to cowl side bolts.
  1. Loosen the LH instrument panel support to cowl side captive bolt.
  1. Position the instrument panel away from the cowl.
    • Disconnect the electronic air temperature control (EATC) hose from the heater plenum.
  1. NOTE: Two technicians are required to carry out this step.
    NOTE: Check the cowl top clips for damage, looseness, or stripped fasteners.
    Remove the instrument panel (04320).
  1. Drain the coolant from the radiator so that the coolant level is below the heater core (18476). For additional information, refer to Section 303-03 .
  1. Recover the refrigerant. For additional information, refer to Section 412-00 .
  1. Loosen the screw and disconnect the electrical connector from the powertrain control module (PCM) (12A650).
  1. Disconnect the heater water hoses (18472) from the heater core.
  1. Disconnect the vacuum supply hose.
  1. Disconnect the condenser to evaporator tube and the evaporator to accumulator tube spring lock couplings from the A/C evaporator core (19860). For additional information, refer to Section 412-00 .
  1. Disconnect the evaporator housing electrical connectors.
  1. Remove the nuts and the washers at the cowl panel.
  1. Remove the screws and the A/C evaporator housing.
  1. Remove the screws and the metal cover.
  1. Remove the screws and the A/C electronic blend door actuator.
  1. Remove the A/C air intake flue damper assist spring (19917).
  1. sxe~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not attempt to bend any part of the A/C damper door shaft (19A580). It is brittle and will break.
    Depress the locking ramp and remove the A/C damper door shaft from the air temperature control door shaft.
  1. sxe~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not attempt to bend any part of the lever. It is brittle and will break.
    Remove the A/C evaporator case outlet door shaft (19B752).
  1. Remove the A/C tube dash panel seal (19B588) and the A/C evaporator drain tube seal (19B739).

Apr 25, 2009 | 1999 Lincoln Town Car

Not finding what you are looking for?
1992 Acura Integra Hatchback Logo

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...