Question about 2000 Ford Explorer

1 Answer

4.0l sohc orings between upper & lower intake manifolds replace

How to change this myself

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

Try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing rear plugs on Taurus Duratek engine


You have to pull the upper intake manifold , that black plastic thing ! Video on youtube showing how to do it . Ford Fusion 3 0L DOHC Upper Intake Gaskets Ford Fusion 3 0L DOHC Spark Plug Replacement

Nov 13, 2016 | Cars & Trucks

1 Answer

On a 2000 explorer 4.0 Soho do I have to remove the injectors to remove the lower intake


REMOVE UPER INTAKE 97 EXPLORER V6 4.0 - YouTube

? 12:22
https://www.youtube.com/watch?v=ugExJ0wkP8A
Jun 11, 2013 - Uploaded by Sum Guy
REMOVE UPER INTAKE 97 EXPLORER V6 4.0 ... I was told that all I have to do is remove the fan belt to get access to it ... FordExplorer 2000 intake manifold gasket upper lower P0174 by froggy - Duration: 36:54. by froggy 36,588 views ... Ford Explorer 4.0L SOHC Rough Idle P0171 P0174 Lean Codes ...

Putting the lower intake on my 1997 Ford Explorer 4.0 OHV ...

? 5:23
https://www.youtube.com/watch?v=qKE1vPxqPHs
Jun 27, 2010 - Uploaded by origionaldz
Putting the lower intake on my 1997 Ford Explorer 4.0 OHV sport .... I do have a 2000 5.0 ... @michaelheiland123654 To dothis job, you have to remove the alternator, unbolt the AC compressor, remove upper intake manifold, remove fuel rail,remove all injectors, ... Do you have the SOHC or OHV version?

1999 Ford Explorer 4.0L -need assistance on removing upper intake ...

www.automotiveforums.com > ... > Ford > Explorer ' Explorer Sport Trac
Sep 20, 2011 - 1999 Ford Explorer 4.0L -need assistance on removing upper intake ...Are you sure you have the OHV/pushrod engine and not the SOHC engine? ... Do youhave the upper intake manifold loose, you just are unable to ... the lower intake gasket, valve cover gaskets, Injector o-rings, plugs and wires. Thanks ...

How to replace upper intake manifold gaskets - Ford Explorer




Dec 09, 2015 | Cars & Trucks

3 Answers

Acellerator switch were is it located on a 99 ford explorer sport 4.0 s.o.h.c.


Who is changing all those parts?

I doubt even one of them was tested or was bad

You need a repair shop that can actually diagnose
& repair vehicles

Mar 03, 2013 | 1999 Ford Explorer

1 Answer

My check engine light came on and machine gave me the codes p0171 and p0174 what do they mean? on a 99 ford explorer sport.


This means both banks have a lean condition. Most likely if you have a 4.0 SOHC motor your upper intake is sucking in air at the orings at the bottom of the intake. These are really bad about when they are cold in the morning the shrink and let air get by and after the engine warms up the orings soften and seal off.

Apr 29, 2011 | Ford Explorer Sport Cars & Trucks

1 Answer

Coolant leaking in and around the intake manifold as well as the under carriage of that same part I think. Outake? I know that the part that attaches to the manifold appears to be metal but the manifold...


The plastic piece is the upper intake manifold. The metal part is the lower intake manifold. Sometimes the gaskets go bad between the upper and lower intake manifolds. But usually the upper intake manifold is cracked and needs replaced.

Nov 11, 2010 | 1993 Buick Park Avenue

1 Answer

Torque sequence for 1996 chevrolet van intake manifold with a 4.3 litre moter


Ha, you tried to fool me with the bit about a 3.5 L motor--I could find that one...here is the complete procedure from AutoZone.com:




Installation To install:
  1. Clean the gasket mounting surfaces. Be sure to inspect the manifold for warpage and/or cracks. If necessary, replace it.
  2. Position the gaskets on the cylinder head with the port blocking plates to the rear and the This Side Up stamps facing upward. Then apply a 3 / 16 in. (5mm) bead of RTV sealant on the front and rear of the engine block at the block-to-manifold mating surface. Extend the bead 1 / 2 in. (13mm) up each cylinder head to seal and retain the gaskets.

    0996b43f80208c7b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold tightening sequence-4.3L engines
  3. Install the lower intake manifold. Tighten the bolts in sequence and in 3 steps, as follows:


    1. Step 1: 26 inch lbs. (3 Nm).
    2. Step 2: 106 inch lbs. (12 Nm).
    3. Step 3: 133 inch. lbs. (15 Nm).

  4. Install or connect the following:

    Power steering pump Alternator bracket bolt near the thermostat housing Wiring harness to the lower manifold components, including the injector, EGR valve and ECT sensor Air conditioning compressor bracket-to-the lower intake manifold pencil braces
  5. Install transmission oil dipstick tube, if necessary.

    Fuel supply and return lines to the rear of the lower intake
  6. Temporarily reattach the negative battery cable, then pressurize the fuel system (by cycling the ignition without starting the engine) and check for leaks.
  7. Disconnect the negative battery cable.
  8. Install or connect the following:

    Heater hose to the lower intake Upper radiator hose to the thermostat housing Distributor assembly and engage the wiring Ignition coil Connect vacuum hoses to the upper and lower intake manifold. New upper intake manifold gasket, making sure the green sealing lines are facing upward Upper intake manifold Manifold retainers. Tighten them to 88 inch lbs. (10 Nm) using two passes. Purge solenoid and bracket Brake booster vacuum hose at the upper intake manifold PCV hose to the rear of the upper intake manifold Vacuum hoses to both the front and rear of the manifold assembly Throttle body Throttle linkage to the upper intake Wiring to the upper intake components including the TP sensor, IAC motor, MAP sensor and the fuel meter Engine cover Air intake assembly
  9. Connect negative battery cable.
  10. Refill the engine cooling system.
  11. Start the engine and check for leaks.

Aug 26, 2010 | 1996 Chevrolet Astro

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

3 Answers

CODES P0171 & P0174 EMISSION SYSTEM SERVICE


if you have the 3.8 liter its more than likely bad intake manifold gaskets or a cracked manifold. Ford has had several TSBs on this issue. O2 sensors do not go bad as often as mechanics say they do. I have a 1999 that after 100 dollars at the parts store solved all lean conditions on the top end. The manifold has three parts to it. A lower aluminum that houses the butterfly blades for the variable intake runners( known vacuum leak were rods protrude at passenger side of lower bad bushings likely cause). Middle riser which uses oring seals which dry out and cause major vacuum leaks. upper is more or less the top cover which uses one large oring to seal. Hope this helps!

Feb 06, 2009 | 2000 Ford Windstar

1 Answer

Rough idle when engine is cold 1997 Explorer V 6


There are 2 common problems on this concern. 1st maybe a dirty MAF sensor. Remove the MAF sensor and clean it with a good electrical cleaner and air dry or light shop air,then reinstall and do a couple of wide open throttle burst to reset it.
2nd problem and we see alot of this is the orings between the upper and lower intake manifold leaks.You would have to remove the upper intake manifold and replace them.

Jan 25, 2009 | 1997 Ford Explorer AWD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...