Question about 2003 Hyundai Tiburon

2 Answers

Change front wheel bearings

What is involved with changing the front wheel bearings on a 2003 Hyundai Tiburon? Thanks

Posted by on

  • Anonymous Mar 15, 2014

    i need to know what the Torque is for a front wheel bearing for a 2003 Hyundai Tiburon

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 60,799 Answers

U will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 Change front wheel bearings - moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Posted on Mar 12, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 140 Answers

THE TIBURON IS FRONT WHEEL DRIVE, SO IT HAS A HUB ASSEMBLY.. TAKE THE WHEEL AND BRAKES OFF, THERE IS THREE BOLTS THAT THE HUB AS CONNECT IT TO THE CAR, AND ONE BIG AXLE NUT IN THE CENTER OF THE ROTOR.. THE ALL THE BOLTS OFF SLIDE YOUR AXLE OUT AND JUST REPLACE YOUR HUB BEARING.. IT SHOULD RUN YOU ABOUT $125 IF YOU DO IT YOURSELF..GOOD LUCK KEITH...

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing front wheel bearing 2003 tiburon how do i get the sensior off so i can take the bracket in to get the old bearing pressed out at the shop


There's one bolt holding the sensor in to the steering knuckle. Remove the bold an pull the sensor out.

When I changed my wheel bearing, the sensor was ceased in place and it broke when I tried to remove it. I had to drill out the bits of sensor that were stuck, then install a new sensor. The new sensor cost around $235.

Alternatively, you could follow the sensor wire to its connector, disconnect the wire and leave the sensor installed. But be aware that the sensor may be damaged when pressing the old wheel bearing out / new one in. In that case, the sensor would have to be replaced anyway.

Oct 17, 2009 | 2003 Hyundai Tiburon

2 Answers

Rear wheel bearing hyundai coupe


just remove the wheel and count the teeth on the ring on the rear brake thats all you need to do. Since you can't drive it take it off and take it in to compare parts so you don't have to go back twice. You will need a new wheel seal and race and bearings.

Sep 29, 2009 | 2001 Hyundai Tiburon

1 Answer

2001 Hyundai Tiburon makes grinding noise while in motion


Stay away, those need to be pressed into place with a hydraulic press, it is best to leave that to a qualified repair shop

Sep 28, 2009 | 2001 Hyundai Tiburon

1 Answer

Wheel bearing


The front 'hub' bearing is 'pressed' out. You have to remove the steering knuckle from the vehicle and using a hydraulic press, replace the bearing by pressing out the old one and then pressing in the new one.

Sep 07, 2009 | 2003 Hyundai Tiburon

1 Answer

What does it take to replace the front wheel bearings on a 2003 Tiburon


the front wheel bearings on your car are not sold except as a front wheel hub assembly with the bearing pre-installed, they run about $100.00 each, to replace them requires no special tools, all u do is remove the wheel, the brake caliper and the brake rotor and the hub nut, then the hub just slides off, u will most likely need a very large socket for the hub retaining nut.

Jul 05, 2009 | 2003 Hyundai Tiburon

1 Answer

Cant find info or book on repairing the front wheel bearrings on my car,or even a "manual" for a 2001 Hyundai Tiburon!


Yes autozone.com has a repair guide for your car,you will be able to get the steering knuckle off,this is where the bearing is but ir requires a press or an equivlant to remove and replace the bearing.

May 25, 2009 | 2001 Hyundai Tiburon

1 Answer

Front wheel bearing


This job is more than a none mechanic is able to do easily.

May 09, 2009 | 1998 Hyundai Tiburon

1 Answer

What's involved in changing the front wheel bearings on a 2003 Hyundai Tiburon? Thank you


A whole bunch its toouch basically your overhauling that side taking off the wheel taking rotor off pulling out the hub dearing and pressing it back inlooking at approx 2-2.5 hors and then you made alignment but if you want to know exacxtly how to do this go to collisionrepairadvice.com its worth it

Mar 12, 2009 | 2003 Hyundai Tiburon

1 Answer

Front wheel bearing keeps going out


you should check the hub carrier for damage or hairline cracks ok m8

Jan 04, 2009 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

2,364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...