Question about 2004 Nissan Maxima

Open Question

How to replace camshaft position sensor on a 2005 f250 5.4 super duty

How to replace the camshaft position sensor on a 2005 ford f250 5.4 super duty?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: Crankshaft and camshaft position sensors

MAke sure you replaced the right sensor and it's the proper design.(If you bought a generic part, it;s probably the wrong thing) I replaced my cam and crank sensors with the generic ones from AutoZone and they had no effect. Took it to Nissan, they replaced both at my expense, AND REPROGRAMMED THE ECU. That fixed that problem SES light hasn;t come on in 6 months....Fingers crossed

Posted on Apr 02, 2009

Ad
heavymetal77
  • 721 Answers

SOURCE: P0340....Camshaft Position Sensor 'A' Circuit Bank

Replace the sensor.

Posted on Jul 14, 2009

  • 170 Answers

SOURCE: The camshaft position sensor has

JUST REPLACE IT IN THE SAME POSITION THAT IT CAM FROM

Posted on Sep 01, 2009

  • 1 Answer

SOURCE: 2004 nissan sentra bad camshaft sensor, replaced

I am having the exact same problem. Did you get it running

Posted on Nov 21, 2009

  • 3640 Answers

SOURCE: Car dies while driving. Code

it is On the back side of the block(below the intake manifold). on 1.8 engine. nissan sentra.

Posted on Aug 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03f250 7.3disel runs good gets hot shutsoff replaced camshaft sensor


Ford F250 Truck Overheating Why - Ford-Trucks

www.ford-trucks.com > ... > Powertrain > Cooling System
Nov 13, 2014 - Here are a few reasons why your Super Duty truck is overheating. ...6.0 Diesel · 1999-2003 7.3 Diesel · 1994.5-1997 7.3 Diesel · 1983-1994 7.3&6.9 Diesel... This article applies to the Ford F-250, F-350 Diesel (2005-2014).

Aug 26, 2015 | Ford Cars & Trucks

1 Answer

P1336 code and drain water seperator


P1336 FORD Crankshaft Position Or Camshaft Position Sensor Input Signal Error

Apr 01, 2014 | 2008 Ford F-250 Super Duty

1 Answer

PO345 PO340 codes


P0345 = Camshaft Position Sensor "A" Circuit Bank 2P0340 = Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor

Mar 29, 2012 | 2007 Ford F-350 Super Duty XLT

2 Answers

Where is the camshaft position sensor at on a 1996 Ford f150?


Section 03-14: Engine Controls, Electronic 1996 F-150, F-250, F-350, F-Super Duty Series and Bronco Vehicles Workshop Manual REMOVAL AND INSTALLATION Camshaft Position (CMP) Sensor Diesel Engine
Removal
  1. Disconnect camshaft position sensor electrical connector.
  1. Remove bolt and camshaft position sensor.


  2. snorkelbobby_40.gif
      please rate

    Feb 14, 2011 | 1996 Ford F150 Regular Cab

    2 Answers

    Po 340 camshaft position sensor. a circuit bank 1 or single sensor


    does it have a 6 cylinder if so need to change camshaft sensor out

    Aug 22, 2010 | 2003 Ford F250 Super Duty Crew Cab

    1 Answer

    F250 will run fine then after turned off will not start. After towed to mechanic then will start again. Anyone else having this problem?


    can you be more specific about motor? diesel? gas? if gas you may have a crank sensor or camshaft sensor goung bad

    Aug 13, 2010 | 2005 Ford F 250 Super Duty

    1 Answer

    Crank but dont start


    Fords are pieces of **** dont never buy one again. ******* **** **** ****

    Jan 31, 2010 | 2001 Ford F350 Super Duty SuperCab

    2 Answers

    Where and how do you put a cam sensor on a Ford f350 powerstroke diesel motor?


    Camshaft Position Sensor located above front crankshaft pulley. Use 10mm socket on 1/4" drive ratchet. Crawl under front of vehicle, disconnect electrical lead, remove bolt, clean timing chain cover area, install new CPS. About $27 at Ford dealer. On some years this is covered under a recent RECALL by Ford...after years of litigation.

    Aug 07, 2009 | 2000 Ford F350 Super Duty Super Cab

    Not finding what you are looking for?
    2004 Nissan Maxima Logo

    Related Topics:

    196 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    726 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...