Question about 2002 Jeep Liberty

1 Answer

2002 jeep brake bulb

Replacing a brake bulb light on the driver side on a 2002 jeep liberty, how do I go about this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

There are 2 screws in the inner part of the vehicle tkae those out and slowly but firmly pull the lamp out. if you need anything else go to collisionrepairadvice.com

Posted on Mar 12, 2009

1 Suggested Answer

alicantecoli
  • 21949 Answers

SOURCE: Need to replace the rear driver's side brake light on my

look for the retaining screws ,they will be either on the lamp upper and lower ,or from the inside of the vehicle behind the trim

Posted on Feb 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side brake light is not working. Replaced bulb, but didn't need to it is the same bulb that works the tail lights, which still worked. Ugh, 2006 jeep liberty. Someone said it was a brake...


THAT RIGHT IF BRAKE SWITCH BAD NO BRAKE LIGHT WILL WORK.SPRAY ELECTRICAL CLEANER IN BULB SOCKET BULB SOCKET COULD HAVE OXIDATION AND CORROSSION CAUSING POOR CONTACT.

Sep 12, 2011 | 2006 Jeep Liberty

1 Answer

Lighting problem


If the wiring on your Liberty hasn't been messed with, the brake light on the left aft side may have been replaced with the wrong one. You may want to double-check to make sure this isn't the case or simply purchase a new one. Also check the bulb socket to make sure there isn't a stray piece of metal in there, causing BOTH bulb filaments to turn on when the brake is depressed.

I hope this helps to solve your problem! :)

May 03, 2010 | 2002 Jeep Liberty

1 Answer

2002 Jeep Liberty flashers, blinkers, taillight and brake light are not working on the left (drivers side


was vehical in an accident? check fuses in pdc under hood this jeep has fuses for the rt side and left side in power distrabrution center.

Feb 23, 2010 | 2002 Jeep Liberty

1 Answer

No brake lights


Check the brake light switch. It should be located under the dash by the arm of the brake pedal. When you push the pedal down with your foot it activates the switch. The switch can be tested with an ohm meter or multimeter. If defective, it will need to be replaced. Hope this helped and good luck.

Jul 19, 2009 | 2002 Jeep Liberty

1 Answer

The brake lights are out on my 2002 Jeep Liberty. I replaced the bulbs but they are still not working. What else could be wrong


ther is a brake light switch on the brake pedal under the dash I suspect it is stuckin the off position when you push on the brake pedal a small tube should come out that is what lets your brake lites come on, if it doesn'tcome ou *** is stuck could be just the theaded part around the tube is bent over
Mike

Jun 26, 2009 | 2002 Jeep Liberty

1 Answer

Need to replace rear brake light on 02 liberty


open tailgate and you will see two retaining screws remove these and give unit a tug to remove then you will be able to replace bulb

May 19, 2009 | 2002 Jeep Liberty

1 Answer

2006 Jeep Liberty parking lights on driver's side won't work


Check fuses inside and underhood, as it's not uncommon for them to be on their own fuse(s)

Apr 25, 2009 | 2006 Jeep Liberty

1 Answer

Tail light won't work but brake light will


Check 10amp fuses #9 and #23 in the fuse block on outbord end of left side of dash panel. With driver door open you should be able to see the small access panel on end of dash.

Mar 05, 2009 | 2002 Jeep Liberty

1 Answer

Need to replace the rear driver's side brake light on my


look for the retaining screws ,they will be either on the lamp upper and lower ,or from the inside of the vehicle behind the trim

Feb 28, 2009 | 2002 Jeep Liberty

2 Answers

Changing brake bulbs


Open the back gate of the jeep. There chould be 2 screws that hold in the light assembly. Remove the screws and pull out the assembly. Replace the bulbs and replave the housing.

Jul 20, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2002 Jeep Liberty Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...