Question about 2002 Buick LeSabre

Open Question

Torque specs 2002 buick lesabre - 2002 Buick LeSabre

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 61 Answers

SOURCE: Need the 2000 Buick LeSabre rear wheel Hub nut torque spec.

Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

Posted on Jul 24, 2009

  • 3 Answers

SOURCE: 2002 Buick LeSabre V-6 Fuel leak but cannot be located.

The fuel lines are steel except for the plastic ends where they need to be flexible for the push-on type connectors. If I am right, those plastic ends pass just under your cabin air intake. Just below that, is a common bend where the steel lines usually rot. If you have high miles they may be baked, or if you had recent engine work they may have been flexed to one side hard enough to split one the three. If one is leaking it is best to replace them all. Don't take chances with gas fumes or leaks. Do it right away!

Posted on Aug 30, 2009

ZJLimited
  • 17970 Answers

SOURCE: I NEED TO KNOW THE TORQUE SPECS FOR THE OIL PAN ON

Exploded view of the oil pan and related components - 1993 vehicle shown

48ac114.jpg


* If removed, install the oil pump pipe and screen. Secure with the retaining bolt(s) and tighten to 89 inch lbs. (10 Nm).

* Place a new formed rubber gasket in the oil pan flange.


* Position the oil pan and secure with the oil pan-to-engine bolts. Tighten the bolts to 124 inch lbs. (14 Nm). Do NOT overtighten the bolts, as this will damage the oil pan, causing a leak.


Hope help with this (remembere rated and comment this help).

Posted on Mar 08, 2010

  • 332 Answers

SOURCE: Torque spec. transmission pan bolts?

20 inch pounds will be plenty

Posted on Mar 10, 2010

  • 1608 Answers

SOURCE: 2002 buick lesabre check engine light on. need a

It would be better if you got the codes read and then post back with the code.There are numerous codes that can cause the check engine light to go on.Auto Zone will do this for free.There are a few other parts stores that do this for free also.Hope this helps.Good luck.

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque sequence of 2002 buick lesabre


Torque sequence for what?What do you want to torque down.Intake,cylinder heads,valve covers,throttle body?You need to be more specific.

Jul 21, 2010 | 2002 Buick LeSabre

1 Answer

Head bolt torques spec


3.8L V6

cylinder head bolt torque

step 1 37 ft lbs.

step 2 an additional 130 degrees

step 3 4 center bolts an additional 30 degrees

Jul 07, 2010 | 1999 Buick LeSabre

1 Answer

Changing trans oil on my 2002 lesabre how do I flush the torque converter or should I?


In order to flush the fluid from the torque converter, once you have the transmission pan removed, start the engine and run the shift lever through the gears, then back to park. Shut off the engine. It would make sense to flush the old fluid from torque converter as you are replacing with a fresh screen and fluid.

Jun 17, 2010 | 2002 Buick LeSabre

1 Answer

What are the torque specs for the intake manifold on a 2002 Buick Rendezvous


the torque spec's require you to tightened to 10 ft lbs and then tighten another 30 degress which will give you about 12 to 15 ft lbs of torque. make sure that you start in the middle and work your way out when tightening manifold because it will crack easily.

May 02, 2010 | 2002 Buick Rendezvous

1 Answer

I am installing a spindle hub bearing assembly on the front wheel of a 1994 Buick Le Sabre. I need the torque spec. for the 3 retaining bolts and hub nut.


Well the torque for the three retaining bolts should be about 75-85 ft lbs.and the hub nut about 100 ft lbs.

Apr 22, 2010 | 1994 Buick LeSabre

1 Answer

Need the 2000 Buick LeSabre rear wheel Hub nut torque spec.


Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

Jul 12, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
2002 Buick LeSabre Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...