Question about Nissan Cars & Trucks

Open Question

How to remove rear tub on d22 king cab pick up

Rear tub removal

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: removal of stereo

there are 2 screws down at climate controls remove them and whole panel pops off, stereo is held in with 4 screws facing you. but it looks bad with a generic stereo fitted nissan have a cd changer that fits in above the stereo where the cup holder is and hooks up to stereo and looks good, not overly flashy,
good luck


Posted on May 05, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 isuzu hombre bed removal


remove the fuel filler and breather from the fuel tank, unclip the rear wiring harness to the rear lights and numberplate lights. and then locate the bolts that attach the tub to the chassis I think there are about 6 or so. when lifting up the rubber blocks may fall out but keep them with the bolts for later use . that should have it done as long as you have some one to help lift it out. hopefully that gets you on your way

Aug 05, 2014 | 1998 Isuzu Hombre

1 Answer

How do i remove the spare tyre off the rodeo


There should be 2 steel rods that you join together in your tool kit behind or under seat depending on cab style (near jack) using another handle or on some the wheel nut wrench for turning handle this goes in black plastic rectangular tube at rear of tub or tray and inserts into winch that holds up spare tyre, anti clockwise lowers. Some models with rear bumper bar may have round plug to take out first (left side)When tyre on ground make sure cable is loose (slack) so you can then get holding braket out of centre hole in rim.

Jul 21, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

How to replace the rear blower motor


Detach the vent tub.
Remove the screws.
Remove the blower motor.
Here is some pictures of were it is...Hope this helped you ??

michael_cass_264.jpgmichael_cass_265.jpg

Jul 05, 2011 | 2005 Mercury Monterey

1 Answer

How do I remove rear wheel bearings for replacement?


The bearings are pressed in. You can remove them yourself and it's about a 45 mins per wheel job. You will need a brass punch, hammer, tub of grease,block of wood, and a socket the same size as the bearing and a bench to work on.
Best to take the drum to a break repair place and have them remove them and press in the new ones.

Jan 10, 2011 | 1992 Toyota Tercel

1 Answer

My 2008 ultima tires will leak air to the extent they are almost completely flat. It started with the passenger side rear almost completely flat. I would fill with air and it will last for 2-5 days. Now...


Your tyres need checking for slow punctures or leaking valves. If you want to do it yourself. You'll need a tub or pool big enough for a complete wheel. Fill it with water, then, remove one wheel at a time and put it in the tub/pool. look for bubbles, the puncture is where the bubble come from.

Of course you could go to a tyre shop and get them to check, once done and you know your tyres are in good order, the only other thought is that it may be someone having fun at your expense, you could get some lockable valve caps.

Jul 19, 2010 | 2007 Nissan Altima 3.5 Sedan

1 Answer

Hi, I've got an 87 wrangler w/ out b/u lights.


The harness runs on the drivers side from the fuse block and goes down inside the rear of the tub. There is a splash shield with a couple clips, remove them and you will see the harness. From there it splits to the left and right side. Also make sure the bolts inside the lenses that connect the rear plate to the tub, are clean because thats your ground. To get any light in all the ground has to be good.

Dec 16, 2009 | 1987 Jeep Wrangler

1 Answer

Rear axel tubs are leaking


you will need to remove the axles, remove diff cover and drain, remove the bolt pin that holds the center rod and remove, do not turn the diff or rotate the axles after this is done, push axles in and remove c clips, then pull axles out, pry out the seals and install new ones, add a touch of grease on the seals and reinstall axles good luck

Nov 01, 2009 | 1997 Chevrolet Camaro

3 Answers

How do i change back spark plugs


The easiest way actually takes a bit longer than trying to get at them from below. Going from below is a great way to tear up your hands.

Go from the top by removing the windshield wiper tub assembly. Remove the wiper arms. Then remove the torx screws that hold the plastic cowling in place. Then remove the support brackets that hold the tub in place. Then remove the 14mm bolts that hold the tub to the firewall. Disconnect the electrical connector to the wiper motor and lift the whole tub assembly out. This portion of the job will take about 1/2 hour, but it opens up the whole back end of the engine so you can reach the plugs and the wires.

Oct 30, 2009 | 2000 Dodge Grand Caravan

1 Answer

Where is the windshield wiper motor on a 2007 Dodge Caravan and how do I replace it?


Wiper Motor: Service and Repair
Removal
REMOVAL
The front wiper motor comes as a unit with a wiper pivot on each end and mounts to a shaft that holds these two inner pivots.
1. Disconnect and isolate the battery negative cable.
2. Remove the wiper arms.
3. Disconnect the washer hose at the in-line connector located near the air cleaner housing.
4. Lift the cowl grille and disconnect the washer hose grommet from the hole in the wiper module. Pull the washer hose and the grommet
completely through the wiper module tub hole.
5. Remove the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
6. Remove the four brace nuts holding the wiper tub to the lower windshield fence.
7. Remove the four bolts underneath the wiper tub inner brace holding the tub to the bulkhead.
8. Remove all four inner support brace mounting nuts and pull the inner braces just free of the mounting studs.
NOTE: The wiper tub will drop down slightly.
9. Disconnect the driver and passenger side wiper link ends at the inner pivots.
10. Remove the two left wiper motor assembly mounting nuts.
11. Remove the two right wiper motor assembly mounting nuts.
12. Partially lift out the wiper motor assembly out of the wiper tub.
13. Disconnect the wiper motor electrical connector.
14. Remove the wiper motor assembly the rest of the way from the wiper tub and remove from vehicle.
--------------------------------------------------------------------------------------------
Wiper Motor: Service and Repair
Installation
INSTALLATION
1. Install front wiper motor assembly onto wiper tub.
2. Connect the electrical connector to the front wiper motor assembly.
3. Install the four mounting nuts. Tighten nuts to 9 Nm (80 in.lbs.).
4. Push the four inner support braces onto the studs and install the four nuts. Tighten the nuts to 9 Nm (80 in.lbs.).
5. Install the four bolts underneath the wiper tub inner braces that hold the wiper tub to the bulkhead. Tighten the bolts to 17 Nm (150 in.lbs.).
6. Install the four nuts holding the wiper tub to the lower windshield fence line. Tighten nuts to 7 Nm (65 in.lbs.).
7. Apply grease to drive link bushings.
NOTE: Make sure to use Mopar(R) approved grease.
8. Attach the driver and passenger side outer wiper linkage to the inner pivots on the front motor assembly and firmly snap into place.
CAUTION: Do not apply too much force to engage link bushing or damage can occur to the drive link bushing.
9. Position the cowl grille in place.
10. Install the washer hose and grommet into the wiper tub.
NOTE: Be sure to properly seat the washer hose grommet into the bottom of the wiper tub.
11. Connect the washer hose at the in-line connector located by the air cleaner housing.
12. Install the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
13. Connect the battery negative cable.
14. Verify that the wiper motor is in the Park position by cycling the wipers system. When done, remove keys from ignition.
15. Install the wiper arms.
16. Align the wiper arms and tighten nuts to 35 Nm (25 ft.lbs.).
17. Install the wiper arm nut caps.

f7c141f.jpg

Sep 13, 2009 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

Land rover Discovery 2004, rear right hand side down 2 inches


If you have the coil spring suspension, then your spring for that corner has really sagged[doubtful] I suspect you actually have the rear air suspension ,and the air spring for the Right/Rear has lost air, allowing the rear end to lower down greatly. Usually, you need a new air spring when one develops a leak. You may or may not be able to see the leak with a spray solution of soapy water after the spring is removed for inspection. Sometimes you have to apply about 20psi of air pressure into the spring to inflate it a bit, then put the spring under water in a big enough tank/tub of water to catch the leak that way.

Apr 01, 2009 | 2004 Land Rover Discovery

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...