Question about BMW 530

Open Question

How to remove rear door handle on 530xi - 530 BMW Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: TRYING TO REMOVE A REAR DOOR OUTER HANDLE

Lower hole in the door jamb loosten allen screw until the cap comes off. Upper hole there is a #20 torx slightly down and inboard of the hole, you need a really long torx bit and pull the handle out slightly. It also helps to pull weatherstrip loose so you can see it.

Posted on Aug 06, 2008

Ad
Brian032472
  • 150 Answers

SOURCE: remove right rear door panel

  1. Remove the rear door power window/power door lock switch
  2. Remove the door handle bezel. Remove the door trim panel screw located behind the door handle bezel.
  3. Remove the door trim panel screws located by the armrest handle.
  4. Remove the door trim panel using J 38778.
  5. Disconnect the electrical connectors.
  6. Remove the door trim panel from the door.
INSTALLATION PROCEDURE

IMPORTANT: Discard the old door trim panel retainers and replace with new retainers before installing the trim panel

  1. Install new trim panel retainers to the rear door trim panel.
  2. Connect the electrical connectors.
  3. Align the door trim panel retainers to the door.
  4. Press the door trim panel at the retainer locations until the retainers are fully seated.
  5. Install the trim panel screws. Tighten Tighten the door trim panel screws to 2 N.m(18 lb in) .
  6. Install the power window/power door lock switch


Posted on Nov 04, 2008

  • 2 Answers

SOURCE: how do i remove the outer rear door handle on a 07 audi Q7

Ok
Remove plastic plug on the inside of door there is 10 mm hole use a hooked pick set pick put through the hole and pull the plastic cir clip towards the back of the door that will release the smaller part of the outer handle then the handle itself can be taken out.this is so simple but so deceiving the actual cir clip is hard to notice because of all the plastic **** on the inside backing plate the cir clip is just on the inside of hole look hard it is 2mm thick & 20mm high (black plastic) place point of pick in between backing plate & cir clip hook it and pull back the front door is based on the same principle but is a lot easier

Posted on Jul 16, 2009

  • 1986 Answers

SOURCE: need to remove inner rear passenger side door

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle

Posted on Nov 05, 2009

  • 54 Answers

SOURCE: bmw 525 4 doors,how to remove rear door outer handle

has to remove the inside panel door and remove the clip inside to open the handle cover then u can see the two nuts and remove them

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

1 Answer

The driver's door on my wife's 2007 530xi was replaced and now the outside door handle sticks a bit when it is released after opening the door - it sticks about half way down - and then it pops down into...


no the door handle is fixed from the inside ,and by the sound of it the handle is catching somewhere and this should have been noticed by the person rebuilding the door ,take it back and ask nicely as most garages will bend over backwards to rectify a fault like this as its their fault and give you another car whilst they do for free

Nov 29, 2010 | 2001 BMW 5 Series

1 Answer

How i can fix door handle on my impala


front or rear?
inside or outside?
What year?

You're probably refering to the outside rear. I had to replace my left rear on a 2002 Impala. It's plastic, and if you don't use the back doors very often, they tend to stick, and snap goes the door handle.
Door handles are available on Ebay for $20-25. Make sure you order the ciorrect one. They are all different.
Remove the door panel. Remove the two nuts to the door handle. It will now be easier to remove the clip and rod to the latch. As I recall, it's easier to remove the rod from the latch, then remove the handle with the rod attached. Transfer the rod to the new handle before installing into the door.

Apr 20, 2010 | 2003 Chevrolet Impala

1 Answer

How to replace a 2003 grand vitara's rear door handle


1. open the rear door
2. open the rear door sidings
3. try loosing the not of the handle
4. remove the steel wirings of the handle
5. install the new rear door handle

Jul 15, 2009 | 2003 Suzuki Vitara

1 Answer

Actuator removal


please rate as solved if this is what you need. You will need to borrow a heavy duty riveter from autozone or wherever you buy the lock cylinder from.


Removal
  1. NOTE: The rear door window glass must be completely raised.
    Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
Trim Panel —Rear Door, Expedition Removal
  1. Remove the power window switchplate (14524).
  1. Disconnect the electrical connector.
  1. Remove the rear door handle trim cover.
  1. Remove the rear inside door handle.
    • Remove the door handle bolt.
  1. Remove the rear door trim panel screws at bottom of panel.
  1. s2j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the rear door trim panel, do not pull directly outward.
    Lift upward and then outward to remove the rear door trim panel (27406).
  1. Remove the rear door watershield.
  1. Disconnect the power door lock actuator electrical connector.
  1. Drill out the power door lock actuator rivet.
9ac2386.gif
  1. Remove and discard the screws.
  1. Remove the power door lock actuator.
    • Disconnect the power door lock actuator rod.
Installation
  1. NOTE: Use new screws when installing the rear door latch.
    To install, reverse the removal procedure.
    • Use Heavy Duty Riveter to install the new rivet.

Jun 14, 2009 | 2002 Ford Expedition

1 Answer

Need to remove the windows switch


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Apr 11, 2009 | 2007 BMW 530xi Sports Wagon

1 Answer

How to remove front passenger door panel on a 04 bmw 530I


how to change passener side door lock assy on 04' bmw 530i?

Apr 11, 2009 | 2007 BMW 530xi Sports Wagon

1 Answer

Rear door on driver side won't open,have taken the panel off the inside of car,seems like the lock won,t travelas far as it does on the other door.is there any way to open this door,thanks[1997 lincoln...


Rear
Removal
  1. Using a small screwdriver, remove the screw cover from the armrest of rear door trim panel (27406).
  1. Remove the two retaining screws.
  1. Using Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry rear door trim panel from door inner panel.
  1. Disconnect electrical connectors.
Installation
  1. Position rear door trim panel on door inner panel, aligning two locators on rear door trim panel. Reverse Removal procedure.
------------------------------------------------------------------------------------ Rear
Removal
  1. Remove door trim panel and watershield. Refer to Section 01-05 .
  1. Check all connections of remote control links and cables. Service as necessary.
  1. Remove remote control assembly.
  1. Remove door latch remote control assembly from latch assembly.
  1. Drill out rivet at bellcrank and link (264B14).
  1. Remove three screws attaching latch assembly to door.
  1. Drill out rivet that attaches actuator motor to door.
  1. Remove latch assembly with actuator motor and door latch control rod lever link assembly.
Installation
  1. Install new bushings and clip onto latch assembly.
  1. Install latch with links and power lock actuator into door cavity.
  1. Position latch assembly to door, aligning screw holes in latch and door. Install three screws. Tighten to 10-13 Nm (89-115 lb-in).
  1. Attach door latch actuator motor to door with a new rivet.
  1. Install bellcrank and link to door using a new rivet.
  1. Install inside door handle and remote control assembly to door.
  1. Open and close door to check latch assembly operation.
  1. Install watershield and door trim panel. Refer to Section 01-05 .
ee8a11f.gif
Item Part Number Description 1 221A00 Door Handle to Door Latch Actuating Cable 2 26446 Rear Door Control Rod Retainer 3 377901 Plug Button 4 26412 Rear Door Latch 5 W623451-S2 Push Nut 6 224A32 Counter Balance 7 22450 Door Outside Handle Tension Spring 8 W701210-S309 Screw 9 224A20 Outside Door Handle Anti Rattle Pivot (2 Req'd) 10 22404 Door Handle 11 224A24 Front Door Outside Handle Spacer (2 Req'd) 12 264A64 Rear Door Actuating Rod 13 22408 Outside Door Handle Anti-Rattle Bumper 14 22428 Outside Door Handle Large Pad 15 N621906-S2 Nut (2 Req'd) 16 N807329 Screw (3 Req'd) 17 26595 Rear Door Electric Latch Actuator (RH) 18 W701566-S47 Rivet 19 431C04-A Rear Door Latch Striker Assembly 20 — Door Lock Striker Plate (Part of Door Shell Assy) 21 W525172-S Rivet (2 Req'd) 22 264B14 Bellcrank and Link (RH) 23 264A50 Bushing 24 N802034-SG Rivet 25 26420 Rear Door Latch Control Rod Link 26 W525172-S Rivet (2 Req'd) 27 21818 RR Door Latch (Inside) 28 A26460 RR Door Latch Push Button Rod 29 21982 Door Latch Rear Striker Assembly 30 N808377-S101 Screw (2 Req'd) 31 250A04 Rear Door Catch 32 N801010-S100 Truss Head Bolt (2 Req'd) 33 N804234-S2 Screw 34 266A74 Rear Door Latch Actuator Retainer 35 24630 Rear Door 36 26552 Rear Door Latch Control Escutcheon A — Tighten to 21-29 Nm (16-21 Lb-Ft) B — Tighten to 10-13 Nm (89-115 Lb-In) C — Tighten to 7-8 Nm (62-70 Lb-In) D — Tighten to 26-34 Nm (20-25 Lb-Ft) E — Tighten to 3-4 Nm (27-35 Lb-In)

Mar 24, 2009 | 1997 Lincoln Continental

1 Answer

Rear door actuator is making a noise, needs replacing


Snap out two door pull strap retainer screw covers. Remove screws.
Remove one screw from lower rear door panel.
Remove screw retaining rear inside door handle cup . Remove rear door inside handle cup.
Using a Trim Pad Removing Tool pry trim panel retaining clips from rear door inner panel.

Feb 12, 2009 | 1995 Mercury Grand Marquis

1 Answer

Remove right rear door panel


  1. Remove the rear door power window/power door lock switch
  2. Remove the door handle bezel. Remove the door trim panel screw located behind the door handle bezel.
  3. Remove the door trim panel screws located by the armrest handle.
  4. Remove the door trim panel using J 38778.
  5. Disconnect the electrical connectors.
  6. Remove the door trim panel from the door.
INSTALLATION PROCEDURE

IMPORTANT: Discard the old door trim panel retainers and replace with new retainers before installing the trim panel

  1. Install new trim panel retainers to the rear door trim panel.
  2. Connect the electrical connectors.
  3. Align the door trim panel retainers to the door.
  4. Press the door trim panel at the retainer locations until the retainers are fully seated.
  5. Install the trim panel screws. Tighten Tighten the door trim panel screws to 2 N.m(18 lb in) .
  6. Install the power window/power door lock switch


Nov 04, 2008 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...