Question about 1996 Ford F350 Crew Cab
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Hello, here is the proceedure. Any questions please ask. Good luck.
The red-striped wires on the 1994-96 DI Turbo engine carry 115 volts DC. A severe electrical shock may be given. Do not pierce the wires.
Posted on Jan 23, 2009
Removal & Installation 1. Disconnect the positive and negative battery cables.
2. Raise and safely support the vehicle.
3. Remove the starter terminal cover.
4. Remove the terminal nut and separate the battery starter cable from the starter motor.
5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.
ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.
6. Remove the starter motor retaining bolts.
7. Remove the starter motor from the vehicle.
8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).
9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).
10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.
11. Install the starter solenoid safety cap. If equipped.
12. Lower the vehicle.
13. Connect the positive and negative battery cables.
14. Start the engine several times to check starter motor operation
Posted on May 27, 2009
Camshaft Position Sensor located above front crankshaft pulley. Use 10mm socket on 1/4" drive ratchet. Crawl under front of vehicle, disconnect electrical lead, remove bolt, clean timing chain cover area, install new CPS. About $27 at Ford dealer. On some years this is covered under a recent RECALL by Ford...after years of litigation.
Posted on Sep 15, 2009
That is your trailer brake controller that is built into your dash. If you are hooked up to a trailer it could mean you are losing your connection or ground to the trailer. If you are not connected to a trailer it means there is a problem with your brake controller possibly a short in the wiring caising the fault code.
Posted on Feb 03, 2010
You need to buy the manual, because you also need to know the order in which to torque them.
usually you start at the middle and circle outward.
But they can differ. Some cars you always need to put in new head bolts. Others are done in several stages. This is too critical to take chances on.
If you really can't afford $19 for a manual, go to the library and xerox the pages.
Posted on Feb 09, 2010
Tips for a great answer:
Jan 04, 2016 | Cars & Trucks
Mar 30, 2015 | 2005 Ford F 350 Super Duty
Jul 25, 2014 | 2008 Ford F-350
Jul 05, 2014 | 2001 Ford F350 Super Duty SuperCab
Aug 01, 2013 | Cars & Trucks
Aug 22, 2011 | 1995 Ford F250
Jul 13, 2010 | 1996 Ford F350 Crew Cab
Sep 17, 2009 | 2003 Nissan Maxima
Nov 27, 2008 | 2004 Ford F350
Jan 10, 2014 | 1996 Ford F350 Crew Cab
36 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: