Question about 2000 Plymouth Grand Voyager

1 Answer

The oil light and warning bell keeps going off. We are trying to find the location of the oil sensor to change it. Where is it?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

On the 2.4L it's on the side of the engine block, facing the firewall.
on the 3.3 and the 3.8L it's mounted next to the oil filter.

Posted on Mar 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My oil warning light on the panel is alerting. I have plenty of oil and no leaks. I need to know where the oil sensor is found. I can't find it in the Haynes Manual.

Most, but not all car engines have an oil pressure switch or sensor and it tends to be located mostly in the oil filter head or screwed into the main oil gallery but I have seen them fitted to the cylinder head oil gallery.
A few engines also have a switch to signal oil filter blockage and others a sensor to monitor oil temperature and there are others with oil level sensors.

It is a good idea to check the vehicle handbook so to be certain what sort of switch or sensor you are seeking.

Oct 08, 2017 | Cars & Trucks

1 Answer

Procedure for turning off warning bell on air bag light sensor on pt cruiser 2004 model

You need to take your motor to a Garage where they can put a diag machine on it.

Apr 29, 2014 | 2004 Chrysler PT Cruiser

1 Answer

Signs bad temp sensor

Bad oil pressure sensor, oil pump, balancer-shaft bearings..
Which grade of oil did you use? Did you try to check the pressure with an oil-pressure gauge?

Sep 14, 2017 | Saab Cars & Trucks

1 Answer

Low engine oil light on after fresh oil change

I am going to assume you have checked the oil level to make sure the engine has enough oil.
If it really is a warning light for low oil it could be that the shop knocked the wire off the sensor.
If it is the warning light for low oil pressure, it could be the sensor or you could really have low oil pressure and still have plenty of oil.

Apr 12, 2013 | 2000 Oldsmobile Silhouette

2 Answers

How do I get the warning bell to go off. When driving my 99 silverado the bell keeps ringing. When I come to a stop it goes off. Very irritating. The dealership can't even figure it out.

What you could do is first you see if you can see a button on the clock the alarm and press it twice and see what happens then you are free to go out of your home i guss??

Jun 19, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

Where is the cam sensor for a 2004 Jeep grand Cherokee 4.7 HO

The can sensor in most cases is located in the below mentioned position.The camshaft position sensor is located just above the oil filter on the right side (sitting in the vehicle) of the engine. But if in case you don't find the sensor there then,
In some model of jeep its located on the BELL housing. ON bell housing to locate the cam sensor:-- AS you stand in front of your JEEP .Head under the bonnet .Then exactly on the right side you will see a fuel rail .Follow the fuel rail and you will reach the bulk head. The can sensor is down there ON THE TOP OF THE BELL HOUSING.
Thanks. keep updated for any more can rate this solution and show your appreciation.

Jun 12, 2010 | 2004 Jeep Grand Cherokee

1 Answer

Oil light constantly comes on and bell rings after a few minutes of driving. I changed oil and oil sensor .where is oil pump located?

the oil pump will be inside the oil pan. could be a weak pump or the pick-up tube may be partially clogged.

Apr 03, 2010 | 2000 Dodge Grand Caravan

1 Answer

The oil light keeps coming on with a bell

If your oil gauge if you have one reads good pressure, more then likely you have a bad sensor, if you just have an oil light, take it to a repair shop where they can do an oil pressure test. Have it check, low oil pressure can cause major engine damage.

Jan 05, 2010 | 2000 Dodge Grand Caravan

1 Answer

Warning bell won't stop sounding

Sounds like your door sensors are going bad and are not relaying to the computer that the doors are fully closed, with that being said you will need to replace them and also at the same time it will stop the door locks from going crazy

May 16, 2009 | 2000 Ford Windstar

1 Answer

Oil sensor

The oil light on your car has nothing to do with oil level in the crankcase but rather oil pressure. The oil pressure switch/sensor is located on the rear of the engine block above the right axle I believe. Unless you have engine noise or suspect low oil pressure, I'd replace it but you could check oil pressure for peace of mind with an pressure gauge if you wish. You may need a special socket to replace it.

Oct 18, 2008 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
2000 Plymouth Grand Voyager Logo

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8755 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides