Question about Cars & Trucks

Open Question

Remove and replace center console for 06 maserati gran sport

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
GM Elec
  • 1000 Answers

SOURCE: need instructions on how to remove center console to access electric window switch.

Here is what I could find, hope it helps.
Good luck.
Regards,


REMOVAL & INSTALLATION

See Figures 1 and 2
The following procedure is a general procedure for console removal. You may have to modify or skip certain steps depending upon your vehicle.

  1. Disconnect the negative battery cable.
  2. Remove the shift knob, floor compartment door and console trim plate.
  3. Remove the instrument panel accessory trim plate.
  4. Unfasten the retaining bolts, detach the connector, then remove the console door.



0900c152800900b7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the retainers, unplug the connector, then remove the console door
  1. Remove the seats, as outlined later in this section, in order to get to the lower rear screw(s) on the side trim panels.
  2. Remove the console side trim panels.
  3. If equipped, remove the switch pack housing with the switches.
  4. Remove the console compartment floor protector, bolt covers and bolts.
  5. Unfasten the screws mounting the console to the instrument panel and tunnel.
  6. Unclip the harness and accessory plug.
  7. Tag and detach all necessary electrical connectors.
  8. If necessary, remove any remaining retainers.
  9. Tilt the rear of the console up, then slide the front tab back out of the instrument panel and remove the console from the vehicle.



0900c152800900b8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Exploded view of a typical console mounting
To install:
  1. Position the console in the vehicle by placing the front tab of the console into the instrument panel slot, making sure to align the screw holes.
  2. Attach the electrical connectors as tagged during removal.
  3. The remaining of installation is the reverse of the removal procedure. Tighten the console retaining screws to 89 inch lbs. (10 Nm).

Posted on May 04, 2009

Ad
jyackle5
  • 8197 Answers

SOURCE: The lid on the center

I once took every single piece of it apart before figuring out that it was indeed 4 bolts. Doh! The two little storage compartments, and the cup holders, just pop out. Two bolts go to the dash, behind the storage bins, and two are under the cup holders. You'll need an extension to get to them. After that it won't see like it'll budge, but there is a big metal clip that it slides into, at the back, on the floor under it. It rusts, so you gotta get low on the console and pull it STRAIGHT BACK.

Remove the package tray and cup holders by grasping and pulling out by hand. There is a wiring block located directly under the stereo with a bolt holding it in place. Loosen the bolt until you can unplug the harness. There are two gold colored bolts on either side of where the wiring block was, remove these. Now if you move back until you are at the front edge of the armrest and look straight down you will see two more bolts that are exactly the size and color of the first two, remove them (you may need to grab them with needle nose pliers after they are loose to get them completely out of there) . This is the tricky part. You have to get in the back seat and pull the console straight back and slightly upward to release the two metal "fingers" that are holding the rear of the console to the floor. These fingers slide into a plate that is bolted to the floor that has two slots in it. DO NOT be shy when you are pulling the console to release these. Trust me, it takes some effort. When you get that released, just pull the whole console out through the rear seat, wiring and all. When you replace the console just reverse this procedure but make sure you don't get hung up where those four bolts go in as you are sliding the console forward and back into place. Hope this helps. Good luck!

Posted on Apr 24, 2011

  • 5370 Answers

SOURCE: p2097 motronic error 06 maserati

P2097:--Seems to be a quite common code.
In most cases the O2 sensor is the problem and needs to be checked and replaced.:

P2097-Down Stream Fuel System 1/2 Rich :---
-----
Possible Causes :---

  • Good Trip Equal to Zero .
  • Exhaust Leak .
  • Engine Mechanical Problem .
  • O2 Sensor ,O2 Signal Circuit ,O2 Return Circuit .
  • Fuel Contamination
  • Oxygen sensor not functioning properly.Spark plug not functioning properly.Primary CATs not functioning properly.
Getting this possibilities checked should point out a direction. ------- You can try this, Clean the MAF sensor( MAF means mass air flow sensor). also clean the throttle body.Clean both with throttle cleaner and get both o2 sensors replaced.And this should take care of problem.------ In most of the cases, this solves the problem . --------- This will help.Thanks.Helpmech.

Posted on Aug 29, 2011

coskuarsiray
  • 208 Answers

SOURCE: Maserati Gran Sport 2006 - Car was idle for a couple of weeks w/ a trickle charger. Disconnected trickle charger and attempted to start car. Lights on the dash lite up normally, pushed starter butto

probably your battery cant conform minimum requirements of digital circuits used to drive starter motor in high tech cars. that is why it works only with external charger. measure your abttery. it should be showing at least 12.4 volts. normally battery should show 12.5. to 12.65 volts. probably your battery has sulfation. end of its life.

Posted on Nov 18, 2011

SOURCE: need help removing center consol to get to radio and heater controls

Its not as complicated as it looks.first of all the front and only part of the center console you need to move simply pops out with two snap in connections at the top and to mounting screws in the back lower bottom...keep in mind moving this part of center console is only for the removal and installation of heater unit...Now for the radio is also quite simple.once you have the heater unit consolek removed,the dash component and vent cover needs to be removed.If you open both car doors @ look
on both sides of your dashboards,theres two covers.remove them..on passenger is a mounting screw for the dash cover.once removed,cover has several snap in connections that will detach it from location...be careful when doig so...now you will see full radio and its mounting bolts...there u have it..hope it helps...

Posted on Oct 14, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the center console lid


On what? Are you trying to get it open or actually remove it?

Jul 30, 2016 | 2005 Maserati Quattroporte

1 Answer

I cannot get my 07 maserati to go from drive to neutral. The car is off I need some guidance


Exactly what type of Maserati do you have? Gran Sport, Gran Turismo, Quattroporte, etc. Do you have the F1 system or the regular automatic transmission?

Mar 09, 2016 | Maserati Cars & Trucks

2 Answers

How do you fix the brake switch on a 1994 buick gran sport


if the switch is not working it will have to be replaced you don`t fix them. but you don`t say what problem your having with it.

Feb 10, 2015 | 1994 Buick Regal Gran Sport

1 Answer

Car will not start


Maserati's have a nasty habit of "NO START" because some moisture got on or into the knock sensor. Have your garage check that sensor and replace if there is any doubt about the condition.

Sep 17, 2014 | 2009 Maserati Quattroporte Sport

1 Answer

Maserati Gran Sport 2006 - Car was idle for a couple of weeks w/ a trickle charger. Disconnected trickle charger and attempted to start car. Lights on the dash lite up normally, pushed starter...


probably your battery cant conform minimum requirements of digital circuits used to drive starter motor in high tech cars. that is why it works only with external charger. measure your abttery. it should be showing at least 12.4 volts. normally battery should show 12.5. to 12.65 volts. probably your battery has sulfation. end of its life.

Nov 18, 2011 | 2006 Maserati Gransport

1 Answer

How do i reset maserati gran turismo 2008 engine oil warning light manually?


How can i reset service light (right side of the dash lower side wrench sign) on 2013 maserati gran turismo?
Thank you

Apr 19, 2011 | 2007 Maserati Granturismo Coupe

1 Answer

How do I remove the center console of a 1994 Buick Regal in order to repair the light gauge showing drive, reverse, neutral etc? (The plastic pieces on both the automatic shift lever and the indicator...


You should be able to remove the trim plate that where the shifter is, it the cover and from there you will be able to replate the bulb for the selector window,

Aug 29, 2010 | 1994 Buick Regal Gran Sport

1 Answer

1994 Buick regal gran sport coupe did not come with a passenger


NOt an expert but my guess is no. First an airbag uses essentially a powder charge to deploy the airbag. Installation and removal is not recommended for joe shade tree mechanic,it can be dangerous. Secondly all that installation has to have a place to mount and a spot inthe dashboard through which it can deploy. Chances are it if didn't come with one an airbag would have no place to "live". If it is even possible to have it done it would probably approach 50% of the value of the typical car that age. Good luck.

Sep 07, 2009 | 1994 Buick Regal Gran Sport

1 Answer

How do I remove an alternator from a 1991 Buick Regal Gran Sport


Is it a serpentine belt? If so, there should be a small pulley, called a tensioner. Loosen that, and you should be able to remove & replace your belt.

Nov 22, 2008 | 1994 Buick Regal Gran Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...