Question about Pontiac Montana

Open Question

Diagram o1 pontaic montana power steering pressure line

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 651 Answers

SOURCE: 1998 pontiac transport montana power steering return hose

if it's the return hose, you can just cut out the bad part and replace it with rubber hose and clamps.

Posted on Dec 02, 2008

  • 299 Answers

SOURCE: pressure line for power steering on 2000 olds

In will have a crimped fitting,low preasure will have clamp.

Posted on Jun 18, 2009

tbirdfan1
  • 3051 Answers

SOURCE: need a serpintine belt routing diagram for a 2000 pontiac Montana

Hello there: here it is
2f0d8b6.jpg

Posted on Jan 17, 2010

  • 2 Answers

SOURCE: suzuki xl7 2007 power steering problem

take it to a suzuki dealer, they just need to replace a piece of spring controlling the steering pressure.. if ur xl7 is 36k miles under,, should be free under warranty.. had the same problem with mine

Posted on Apr 05, 2010

wrenchjockey
  • 75 Answers

SOURCE: Where do I find a diagram to change the power

REMOVAL

  1. Disconnect negative battery cable.
  2. Remove sight shield.
  3. Remove module bracket.
  4. Disconnect No. 6 spark plug wire to prevent damage to wire.
  5. Remove radiator fan shroud assembly.
  6. Remove top RH isolated radiator mount bracket.
  7. Remove remote air cleaner.
  8. Remove ignition coil.
  9. Disconnect electrical connector on power steering pressure switch at steering gear.
  10. Remove pressure switch to allow for tool clearance.
  11. Remove screw at pressure switch and return line bracket.
  12. Remove anti rattle clips from power steering lines.
  13. Remove plastic strap attaching steering gear heat shield to power steering return line.
  14. Remove plastic strap attaching lines to transfer tube on the steering gear.
  15. Disconnect Electronic Vacuum Regulator (EVR) valve wire.
  16. Remove the ground wire from back of engine block.
  17. Remove pressure line fitting at power steering pump using a 5/8 inch flare nut wrench.
  18. Loosen clamp and remove return line at pump.
  19. Loosen clamps and remove return line at power steering oil cooler.
  20. Remove pressure line fitting (gold in color) at steering gear, using an 18mm open end wrench.
  21. Remove return line fitting (silver in color) at steering gear, using an 18mm open end wrench.
  22. Loosen two screws retaining power steering oil cooler to sub frame.
7c30cde.gif

Posted on Oct 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power or connection to obd-11 on 2001 pontaic montana


Attach OBD scanner to pin connector.
turn the key to the "on" position, this brings power to OBD11 connection.
follow mfg directions for the scanner you have.

Apr 06, 2015 | 2001 Pontiac Montana

1 Answer

Power steering pressure line diagram of 1992 toyota pickup


There are several diagrams at the following link:
https://www.google.com/search?q=power+steering+pressure+line+diagram+of+1992+toyota+pickup&es_sm=93&tbm=isch&tbo=u&source=univ&sa=X&ei=oGsDVau9Cde5oQS624Fo&ved=0CB4QsAQ
All you have to do (since you didn't tell me what model you have) is look at the diagrams and find which one looks like your model Toyota.

Mar 12, 2015 | 1992 Toyota Pickup

1 Answer

2000 pontaic montana will turn over but not spark


You'll need a repair book or shop manual to get the wiring diagrams and test procedures.
You would need to know if you have power going into the module and a signal from the computer.

Feb 16, 2013 | 2000 Pontiac Montana

1 Answer

Power steering pump replacement 2002 pontiac montana


Remove the drive belt, remove the 3 mounting bolts by using a socket ththrough the holes in the drive pulley. Remove the upper intake to give you room, slide off the rubber return hose, remove the pressure line and lift out the pump. Just reverse the process to instill the new pump. And fill with the proper fluid.

Jan 09, 2013 | 2002 Pontiac Montana

1 Answer

2003 pontaic montana horn doesn't work


Has the airbag been deployed and removed?

Jan 04, 2013 | 2003 Pontiac Montana

1 Answer

Car is leaking power steering fluid can u give me the diagram for the high pressure power steering line


We do not have a diagram but follow the high pressure hose from the PS pump to the steering gear, clean it off with a pressure washer first and then you can id the leak which will be the high pressure hose I bet..

Sep 06, 2012 | 1996 Ford Contour

1 Answer

Replace power steering pump


Remove the belt, there are 3 bolts that you have to remove through the openings in the pulley. Remove the power steering lines from the hold down bracket on the left lower side of the engine then remove the return rubber hose from the steel line by removing the front right tire and splash shield. Then you can lift the pump up and out and have room to remove the pressure line.

Jan 29, 2011 | 2000 Pontiac Montana

1 Answer

Where do I find a diagram to change the power steering pressure line hose in my 1990 Lincoln Continental?


REMOVAL

  1. Disconnect negative battery cable.
  2. Remove sight shield.
  3. Remove module bracket.
  4. Disconnect No. 6 spark plug wire to prevent damage to wire.
  5. Remove radiator fan shroud assembly.
  6. Remove top RH isolated radiator mount bracket.
  7. Remove remote air cleaner.
  8. Remove ignition coil.
  9. Disconnect electrical connector on power steering pressure switch at steering gear.
  10. Remove pressure switch to allow for tool clearance.
  11. Remove screw at pressure switch and return line bracket.
  12. Remove anti rattle clips from power steering lines.
  13. Remove plastic strap attaching steering gear heat shield to power steering return line.
  14. Remove plastic strap attaching lines to transfer tube on the steering gear.
  15. Disconnect Electronic Vacuum Regulator (EVR) valve wire.
  16. Remove the ground wire from back of engine block.
  17. Remove pressure line fitting at power steering pump using a 5/8 inch flare nut wrench.
  18. Loosen clamp and remove return line at pump.
  19. Loosen clamps and remove return line at power steering oil cooler.
  20. Remove pressure line fitting (gold in color) at steering gear, using an 18mm open end wrench.
  21. Remove return line fitting (silver in color) at steering gear, using an 18mm open end wrench.
  22. Loosen two screws retaining power steering oil cooler to sub frame.
7c30cde.gif

Oct 21, 2010 | 1990 Lincoln Continental

1 Answer

I NEED TO REPLACE THE POWER STEERING PRESSURE SENSOR BUT I NEED A DIAGRAM OF WHERE IT WOULD BE ON A 99 CRHYSLER CONCORDE


Hi!
The power steering pressure switch is mounted in the pressure line between the steering gear and the steering pump.
Just follow the line from the pump and you'll find it.
Good luck

Feb 10, 2010 | 1999 Chrysler Concorde

1 Answer

NEED DIAGRAM FOR POWER STEERING SYSTEM


There is usually no diagram for the power steering on a vehicle. On power steering you have a pressure line and a low pressure return line. The pump is located on the front of the engine and has a line that is bolted into it, this is the pressure line coming out going to the steering gearbox where it is bolted in also. The other line has a clamp holding it in place, this is the low pressure return line coming back from the gearbox. If the gearbox is the rack and pinion steering type then you may have a couple of extra high pressure lines on it to operate the rack portion of the steering. Good Luck, RAC

Apr 18, 2009 | 2006 Chevrolet Cobalt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...