Question about 2008 Jeep Wrangler

Open Question

Need a diagram for the hose routing for the rear windshield washer fluid

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 512 Answers

SOURCE: front widshield washer fromm 1999 Cherokee doesn't work

the same reservoir is used for both ...it uses separate pump motors.....if the wipers are working the fuse for the washer pump is good...check the power and ground for the pump...

Posted on Nov 03, 2008

Ad
JustJeeps
  • 74 Answers

SOURCE: Rear tailgate windshield washer does not work

the dash bezel justs pulls off and the switch panel has a few screws..easy one

Posted on Nov 30, 2008

jrock1094
  • 158 Answers

SOURCE: My 96 Jeep GC windshield washer isn't squirting.

your rear wiper motor might be faulty,in the front i would check your fluid level-if it is full and you hear the pump running-check your washer lines to see if they are pinched-usually around where the hood closes

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

1 Answer

Where is the fuse for the water pump for the window washer


A washer pump in a car's windshield wiping system moves washer fluid from a reservoir through hoses. The motorized pump pressurizes the fluid to allow it to be squirted from the hoses through nozzles onto the front and/or rear windshield of a car. The washer fluid helps windshield wipers get rid of rain, dirt, or other objects that can interfere with a driver's visibility. If your washer fluid is not being sent out when activated, the solution could simply be filling the washer system's reservoir with more fluid or cleaning the nozzles and hoses. In more severe cases, the washer pump may need to be replaced. Here are steps to troubleshoot a windshield-washer pump.

Try this link in case you are stuck:

How to Troubleshoot Windshield Washer Pump

Here is another YT video for a similar purpose:

Windshield Washer Pump and System Diagnosis

Apr 13, 2015 | 2001 Ford Explorer Sport Trac

1 Answer

Leaking windshield washer fluid from roof


Probably broken fluid hose. Replace same.

Feb 21, 2014 | Chevrolet Tahoe Cars & Trucks

2 Answers

I need to replace the hose from the windshield washer fluid reservoir to I don't know where. I don't know where it goes from there. A diagram of the hoses would be helpful.


The pipe should run from the washer jets along the back edge of the bonnet then through via the hinge inot the engine compartment.

Dec 23, 2012 | Cars & Trucks

1 Answer

How to connect the windshild fluid hose routing


Try using a "Tooth-pic" or pin tool to clean out debris from the two spouts at the windshield. If these are clogged, and I've seen it happen hundreds of times, the washer fluid will go nowhere. It's like having your finger stuck inside a water hose......nothing will come out. Many people use water from a hose to fill the washer bottle and this water has contaminants that will clog the spout at the windshield. Also poorly made washer fluid will clog the line and thus nothing will come out. To free up the clog just use a tooth-pic to dislodge the debris. The best windshield washer fluid I could recommend to ease this problem would be a home-made batch of 40% Windex to 60% distilled water. God Luck!

Dec 29, 2011 | Cadillac Seville Cars & Trucks

2 Answers

How do I fix my window washer pump on my 2000 dodge caravan?


One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and splash shield.
  4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
  5. Place a drain pan under the reservoir if it contains fluid.
  6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
  7. Let the fluid drain from the reservoir.
  8. Remove the mounting screws and the reservoir.
To Install:
  1. Install the fluid reservoir with the mounting screws.
  2. Connect the front washer hose in the engine compartment.
  3. Connect the electrical connectors and rear washer hose.
  4. Install the splash shield.
  5. Install the right front wheel.
  6. Lower the vehicle.
prev.gif next.gif

Aug 27, 2010 | 2000 Dodge Caravan

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

1 Answer

Windshield washer fluid hose disconnected


Yoou can pick up the hose and more connection fittings at orielly's, route along fire wall and fender (keep away from heat of engine)

Feb 12, 2009 | 1996 Honda Accord

3 Answers

Windshield washer Pump doesn't run, but the pump checks out good


there is another small relay box just below the windshield washer reservoir about 11/2" wide x about 4" long the washer pump relay is in there



Nov 23, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...