Question about 2006 Mazda 3

Open Question

How to remove a stub-shaft from a 2006 mazda 3 is 2.3 l

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trans fluid leaking out cv joints after clutch change? Fairly constant drip. Has the mechanic over filled or not put seals in properly? Subaru Forester 2006


I believe the Half Shaft is totally isolated from the Gear oil in the trani, back in '06. The half shaft should bolt to the Trani Stub with 6 (or8) allen keyed bolts. If I had to guess, I think the mechanic may have ruined the seal at the half shaft bolt up point. Maybe he was a bit hard on the stub that sticks out to accept the half shaft

Mar 02, 2016 | Subaru Cars & Trucks

1 Answer

How to get cv shaft out


Remove Wheel Remove Lower Control Arm Joint Pull Stub Axle Outward Remove Nut Holding Splinned Shaft ,Remove Shaft ,Pull Shaft Out Of Gear Box, Clips In May Need A Good Clout To Help It Come Out.Re Install In Reverse

Mar 28, 2013 | 1989 Isuzu Trooper

1 Answer

The rubber cover on the left side axel is tore. I need to replace the joint I think. How do I do this?


You will need to remove the front wheel. Unbolt the caliper and move aside. Remove the rotor. Remove the axle nut. Unbolt the 3 hub/ bearing bolts and remove hub assembly. Pull the axle shaft out through the opening left by the hub bearing. Cut off the old boot and clamps. Hold axle shaft and tap joint and axle stub off of shaft with a hammer. Install new boot on shaft and reverse steps for assembly.

Feb 06, 2011 | 2000 Jeep Grand Cherokee

1 Answer

How to remove front axle on a 2002 dodge intrepid


raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Oct 30, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

I have a chrysler lhs 1994 with a bad front wheel bearing and i need instruction on repair


These are the steps you need to follow for this procedure if you have the proper tools.
  1. Remove front caliper assembly and rotor from the steering knuckle as outlined under "Caliper, Replace" in the "Disc Brake" unit repair section.
  2. Remove hub and bearing to stub axle retaining nut.
  3. Disconnect hub bolts then remove hub and bearing assembly from steering knuckle by sliding it straight off end of stub axle. If metal seal on hub and bearing assembly is seized to steering knuckle and becomes dislodged on hub and bearing assembly during removal, or when removing hub and bearing, the finger disc on hub becomes damaged, hub and bearing assembly must be replaced.
  4. If hub and bearing will not slide out of knuckle, insert a prybar between hub and steering knuckle and gently pry hub and bearing from knuckle.
  5. Tighten stub shaft nut, lower vehicle and with brakes applied, torque stub shaft nut to 70 - 90 ft. lbs.

Aug 27, 2010 | 1994 Chrysler LHS

1 Answer

Does a mazda 3 1.6 ts 2006 have a radio code as


it turns out that you can install your own code and remove or change it
so i have removed the previous and installed my own

Jan 19, 2010 | 2005 Mazda 3

2 Answers

How do I remove the outer CV joint from the axle?


After removing the axle assembly, clip the metal band on the large side of the rubber grease boot, slide the boot back on the axle shaft. Pull the outer CV housing and axle stub away from the CV joint. You will find that there is a circlip holding the bearing carrier onto the axle shaft, remove it. Remove the boot.

Installation is the reverse of removal.

Dec 26, 2009 | Mazda 626 Cars & Trucks

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

How to take a stub shaft off a 1984 turbo -350 transsmission


stub shaft is affixed from inside the transmission

May 19, 2008 | 1983 Chevrolet Silverado

Not finding what you are looking for?
2006 Mazda 3 Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...